-
Notifications
You must be signed in to change notification settings - Fork 52
NI RFmx SpecAn PAVT Configuration Functions
Alex Starche edited this page Feb 28, 2022
·
3 revisions
- RFmxSpecAn_PAVTCfgMeasurementLocationType
- RFmxSpecAn_PAVTCfgMeasurementBandwidth
- RFmxSpecAn_PAVTCfgMeasurementIntervalMode
- RFmxSpecAn_PAVTCfgNumberOfSegments
- RFmxSpecAn_PAVTCfgSegmentType
- RFmxSpecAn_PAVTCfgSegmentStartTimeStep
- RFmxSpecAn_PAVTCfgSegmentStartTimeList
- RFmxSpecAn_PAVTCfgMeasurementInterval
- RFmxSpecAn_PAVTCfgSegmentMeasurementInterval
- Array Apis
int32 __stdcall RFmxSpecAn_PAVTCfgMeasurementLocationType (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 measurementLocationType);
Configures the measurement location type for the segments.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| measurementLocationType | int32 | Specifies whether the location at which the segment is measured is indicated by time or trigger. |
| RFMXSPECAN_VAL_PAVT_MEASUREMENT_LOCATION_TYPE_TIME (0) | The measurement is performed over a single record across multiple segments separated in time. The measurement locations of the segments are specified by the RFMXSPECAN_ATTR_PAVT_SEGMENT_START_TIME) attribute. The number of segments is equal to the number of segment start times. |
|---|---|
| RFMXSPECAN_VAL_PAVT_MEASUREMENT_LOCATION_TYPE_TRIGGER (1) | The measurement is performed across segments obtained in multiple records, where each record is obtained when a trigger is received. The number of segments is equal to the number of triggers (records). |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgMeasurementBandwidth (niRFmxInstrHandle instrumentHandle, char selectorString[], float64 measurementBandwidth);
Configures the measurement bandwidth.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| measurementBandwidth | float64 | Specifies the bandwidth over which the signal is measured. This value is expressed in Hz. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgMeasurementIntervalMode (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 measurementIntervalMode);
Configures the measurement interval mode.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| measurementIntervalMode | int32 | Specifies the mode of configuring the measurement interval. |
| RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_UNIFORM (0) | The time offset from the start of segment and the duration over which the measurement is performed is uniform for all segments and is given by the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_OFFSET) attribute and the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_LENGTH) attribute respectively. |
|---|---|
| RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_VARIABLE (1) | The time offset from the start of segment and the duration over which the measurement is performed is configured separately for each segment and is given by the RFMXSPECAN_ATTR_PAVT_SEGMENT_MEASUREMENT_OFFSET) attribute and the RFMXSPECAN_ATTR_PAVT_SEGMENT_MEASUREMENT_LENGTH) attribute respectively. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgNumberOfSegments (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 numberOfSegments);
Configures the number of segments.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| numberOfSegments | int32 | Specifies the number of segments to be measured. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentType (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 segmentType);
Configures the segment type.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| segmentType | int32 | Specifies the type of segment. |
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_PHASE_AND_AMPLITUDE (0) | Phase and amplitude is measured in this segment. |
|---|---|
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_AMPLITUDE (1) | Amplitude is measured in this segment. |
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_FREQUENCY_ERROR_MEASUREMENT (2) | Frequency error is measured in this segment. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentStartTimeStep (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 numberOfSegments, float64 segment0StartTime, float64 segmentInterval);
Configures the list of the segment start times based on segment0StartTime and segmentInterval. This function is used when the segments to be measured have equal duration.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| numberOfSegments | int32 | Specifies the number of segments to be measured. |
| segment0StartTime | float64 | Specifies the start time for segment0. This value is expressed in seconds. |
| segmentInterval | float64 | Specifies the difference in the start times between consecutive segments. This value is expressed in seconds. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentStartTimeList (niRFmxInstrHandle instrumentHandle, char selectorString[], float64 segmentStartTime[], int32 numberOfElements);
Configures the list of the segment start times.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| segmentStartTime | float64[] | Specifies the start time of measurement of the segments. This value is expressed in seconds. You can use this parameter only when you set the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_LOCATION_TYPE) attribute to RFMXSPECAN_VAL_PAVT_MEASUREMENT_LOCATION_TYPE_TIME. |
| numberOfElements | int32 | Specifies the number of elements in each array. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgMeasurementInterval (niRFmxInstrHandle instrumentHandle, char selectorString[], float64 measurermentOffset, float64 measurermentLength);
Configures the measurement offset and measurement length for the segments.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| measurermentOffset | float64 | Specifies the time offset from the start of the segment for which the phase and amplitude values are computed. This value is expressed in seconds. The default value is 0. |
| measurermentLength | float64 | Specifies the duration within the segment over which the phase and amplitude values are computed. This value is expressed in seconds. The default value is 1 millisecond. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentMeasurementInterval (niRFmxInstrHandle instrumentHandle, char selectorString[], float64 segmentMeasurementOffset, float64 segmentMeasurementLength);
Configures the segment measurement offset and length for the segments.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| segmentMeasurementOffset | float64 | Specifies the time offset from the start of the segment for which the phase and amplitude, amplitude, or frequency error values are computed. This value is expressed in seconds. This attribute is valid only when you set the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_INTERVAL_MODE) attribute to RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_VARIABLE. |
| segmentMeasurementLength | float64 | Specifies the duration within each segment over which the phase and amplitude, amplitude, or frequency error values are computed. This value is expressed in seconds. This attribute is valid when you set the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_INTERVAL_MODE) attribute to RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_VARIABLE. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentTypeArray (niRFmxInstrHandle instrumentHandle, char selectorString[], int32 segmentType[], int32 numberOfElements);
Configures an array of segment types.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| segmentType | int32[] | Specifies the type of segment. |
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_PHASE_AND_AMPLITUDE (0) | Phase and amplitude is measured in this segment. |
|---|---|
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_AMPLITUDE (1) | Amplitude is measured in this segment. |
| RFMXSPECAN_VAL_PAVT_SEGMENT_TYPE_FREQUENCY_ERROR_MEASUREMENT (2) | Frequency error is measured in this segment. |
| numberOfElements | int32 | Specifies the number of elements in each array. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
int32 __stdcall RFmxSpecAn_PAVTCfgSegmentMeasurementIntervalArray (niRFmxInstrHandle instrumentHandle, char selectorString[], float64 segmentMeasurementOffset[], float64 segmentMeasurementLength[], int32 numberOfElements);
Configures an array of segment measurement offsets and lengths for the segments.
| Input | ||
|---|---|---|
| Name | Type | Description |
| instrumentHandle | niRFmxInstrHandle | Identifies the RFmx session. You can obtain this parameter from the RFmxSpecAn_Initialize) function. |
| selectorString | char[] | Comprises the signal name. If you do not specify the signal name, the default signal instance is used. Example: "" "signal::sig1" You can use the RFmxSpecAn_BuildSignalString) function to build the selector string). |
| segmentMeasurementOffset | float64[] | Specifies the time offset from the start of the segment for which the phase and amplitude, amplitude, or frequency error values are computed. This value is expressed in seconds. This attribute is valid only when you set the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_INTERVAL_MODE) attribute to RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_VARIABLE. |
| segmentMeasurementLength | float64[] | Specifies the duration within each segment over which the phase and amplitude, amplitude, or frequency error values are computed. This value is expressed in seconds. This attribute is valid when you set the RFMXSPECAN_ATTR_PAVT_MEASUREMENT_INTERVAL_MODE) attribute to RFMXSPECAN_VAL_PAVT_MEASUREMENT_INTERVAL_MODE_VARIABLE. |
| numberOfElements | int32 | Specifies the number of elements in each array. |
| Name | Type | Description |
|---|---|---|
| status | int32 | Returns the status code of this operation. The status code either indicates success or describes an error or warning condition. Examine the status code from each call to an RFmx function to determine if an error has occurred. To obtain a text description of the status code and additional information about the error condition, call the RFmxSpecAn_GetError) function. The general meaning of the status code is as follows: |
| Value | Meaning |
|---|---|
| 0 | Success |
| Positive Values | Warnings |
| Negative Values | Errors |
Creating and Setting Up a gRPC Server
Session Utilities API Reference
gRPC API Differences From C API
Sharing Driver Sessions Between Clients
C API Docs
NI-DAQmx
- gRPC API Differences From C API
- Task Configuration And Control
- Channel Configuration And Creation
- Timing
- Triggering
- Read Functions
- Write Functions
- Export Hardware Signals
- Scale Configuration
- Internal Buffer Configuration
- Advanced Functions
- System Configuration
- Error Handling
- Buffer Attributes
- Calibration Info Attributes
- Channel Attributes
- Device Attributes
- Export Signal Attributes
- Persisted Channel Attributes
- Persisted Scale Attributes
- Persisted Task Attributes
- Physical Channel Attributes
- Read Attributes
- Scale Attributes
- System Attributes
- Task Attributes
- Timing Attributes
- Trigger Attributes
- Watchdog Attributes
- Write Attributes
NI-DCPOWER
- Setup Functions
- Configure Functions
- Measurement Functions
- Control Functions
- Trigger And Event
- Attribute Functions
- Query Functions
- Calibration Functions
- Utility Functions
- Supported Device
- Source Attributes
- Transient Attributes
- Voltage Attributes
- Current Attributes
- Pulse Voltage Attributes
- Pulse Current Attributes
- Cutoff Attributes
- Measurement Attributes
- Trigger Attributes Functions
- Event Attributes
- Advanced Attributes
- Inherent Ivi Attributes
- Supported Device Attributes
NI-DIGITAL PATTERN DRIVER
- Init And Close Functions
- Session Locking Functions
- Utility Functions
- Error Handling Functions
- Calibration Functions
- Attributes Functions
- Pin Map Functions
- Low Level Functions
- Low Level Action Functions
- Pin Control Functions
- Static IO Functions
- Clock Generator Functions
- Levels And Timing Functions
- TDR Functions
- PPMU Configuration Functions
- DC Voltage Functions
- DC Current Functions
- PPMU Action Functions
- Pattern Configuration Functions
- Pattern Action Functions
- History Ram Functions
- Source Memory Functions
- Capture Memory Functions
- Triggers And Events Functions
- Conditional Jump Trigger Functions
- Sequencer Flag Functions
- Sequencer Register Functions
- Match Fail Combination Functions
- Pattern Results Functions
- Sort Results Functions
- Frequency Measurement Functions
- IVI Inherent Attributes
- Specific Driver Information Attributes, Read Only
- Driver Setup Information Attributes
- Device Attributes
- Pin Control Attributes
- Level Configuration Attributes
- Trigger Configuration Attributes
- PPMU Attributes
- Patterns Attributes
- Pattern Opcode Event Attributes
- Timing Offset Attributes
- Keep Alive Attributes
- Frequency Measurement Attributes
- Clock Generator Attributes
- History RAM
- Synchronization Attributes
- TDR Endpoint Termination Attributes
NI-FGEN
- Setup Functions
- Configuration Functions
- Standard Output Functions
- Arbitrary Waveform Output Functions
- Arbitrary Sequence Output Functions
- Incremental Waveform Write Functions
- Configure Clock Functions
- Trigger And Syncronizations Functions
- 5404 Routing Functions
- Script Output Functions
- Configure Onboard Signal Processing Functions
- Configure Peer To Peer Functions
- Attribute Functions
- Waveform Control Functions
- Error Functions
- Output Attributes
- Arbitrary Waveform Attributes
- Data Transfer Attributes
- Onboard Signal Processing Attributes
- Peer To Peer Attributes
- Standard Function Attributes
- Clock Attributes
- Event Attributes
- Triggering Attributes
- Instrument Specific Attributes
- Inherent IVI Attributes
- 5401 5411 5431
NI-RFmx Bluetooth
- gRPC API Differences From C API
- General Functions
- Configuration Functions
- Set And Get Attribute Functions
- Fetch Results Functions
- Utility Functions
- Build String Functions
- Advanced Functions
- General Attributes
- Trigger Attributes
- Packet Attributes
- Auto Detect Signal Attributes
- Modacc Attributes
- ACP Attributes
- Twenty dB Attributes
- Frequency Range Attributes
- TXP Attributes
- Advanced Attributes
NI-RFmx NR
- gRPC API Differences From C API
- General Functions
- Configuration Functions
- Set And Get Attributes Functions
- Fetch Results Functions
- Utility Functions
- Build String Functions
- Advanced Functions
- General Attributes
- Trigger Attributes
- Signal Detection Attributes
- Component Carrier Attributes
- List Attributes
- Modacc Attributes
- ACP Attributes
- CHP Attributes
- OBW Attributes
- SEM Attributes
- TXP Attributes
- Pvt Attributes
- Advanced Attributes
NI-RFmx LTE
- gRPC API Differences From C API
- General Functions
- Configuration Functions
- Ch Configuration Functions
- NB IoT Configuration Functions
- ModAcc Configuration Functions
- ACP Configuration Functions
- CHP Configuration Functions
- OBW Configuration Functions
- SEM Configuration Functions
- PVT Configuration Functions
- SlotPhase Configuration Functions
- SlotPower Configuration Functions
- Set And Get Attribute Functions
- ModAcc Fetch Functions
- ACP Fetch Functions
- CHP Fetch Functions
- OBW Fetch Functions
- SEM Fetch Functions
- PVT Fetch Functions
- SlotPhase Fetch Functions
- SlotPower Fetch Functions
- Utility Functions
- Build String Functions
- Advanced Functions
- General Attributes
- Trigger Attributes
- Component Carrier Attributes
- ModAcc Attributes
- ACP Attributes
- CHP Attributes
- OBW Attributes
- SEM Attributes
- PVT Attributes
- SlotPhase Attributes
- SlotPower Attributes
- Advanced Attributes
NI-RFmx SpecAn
- gRPC API Differences From C API
- General Functions
- Configuration Functions
- Set And Get Attribute Functions
- Read Functions
- Fetch Functions
- Utility Functions
- Marker Functions
- Build String Functions
- Advanced Functions
- General Attributes
- Trigger Attributes
- ACP Attributes
- Cdf Attributes
- CHP Attributes
- Fcnt Attributes
- Harm Attributes
- OBW Attributes
- SEM Attributes
- Spectrum Attributes
- Spur Attributes
- TXP Attributes
- AMPM Attributes
- Dpd Attributes
- IQ Attributes
- IM Attributes
- NF Attributes
- Phasenoise Attributes
- PAVT Attributes
- Advanced Attributes
NI-RFmx WLAN
- gRPC API Differences From C API
- General Functions
- Configuration Functions
- Set And Get Attribute Functions
- Fetch DSSS ModAcc Functions
- Fetch OFDM ModAcc Functions
- Fetch SEM Functions
- Fetch TXP Functions
- Fetch PowerRamp Functions
- Utility Functions
- Build String Functions
- Advanced Functions
- General Attributes
- Trigger Attributes
- OFDM Attributes
- Auto Detect Signal Attributes
- DSSS ModAcc Attributes
- OFDM ModAcc Attributes
- SEM Attributes
- TXP Attributes
- PowerRamp Attributes
- Advanced Attributes
NI-RFSA
- General Functions
- Configuration Functions
- Acquisition Functions
- Utility Functions
- Calibration Functions
- General Attributes
- Vertical Attributes
- Signal Path Attributes
- Acquisition Attributes
- Acquisition Attributes
- Triggers Attributes
- Events Attributes
- Device Characteristics Attributes
- Peer To Peer Streaming Attributes
- Configuration List Attributes
- Inherent IVI Properties Attributes
- De-embedding Attributes
- Self Calibration Attributes
- Factory Calibration Attributes
- External Alignment Attributes
- Device Specific Attributes
NI-RFSG
- General Functions
- Generation Configuration
- Utility Functions
- Calibration Functions
- Arb Attributes
- Clock Attributes
- Configuration List Attributes
- De-embedding Attributes
- Device Characteristics Attributes
- Device Specific Attributes
- Events Attributes
- External Calibration Attributes
- Inherent IVI Attributes Attributes
- IQ Impairment Attributes
- Load Configurations Attributes
- Modulation Attributes
- Obsolete Attributes
- Peer To Peer Attributes
- RF Attributes
- Self Calibration Attributes
- Triggers Attributes
NI-SCOPE
- Setup Functions
- Configure Functions
- Attribute Functions
- Acquisition Functions
- Measurement Functions
- Calibrate Functions
- Utility Funcitons
- Error Handling Functions
- IVI Compliance Or Obsolete Functions
- Vertical Attributes
- Horizontal Attributes
- Trigger Attributes
- Clocking Attributes
- Synchronization Attributes
- Acquisition Attributes
- Waveform Measurements Attributes
- Onboard Signal Processing Attributes
- Peer To Peer Streaming Attributes
- Device Attributes
- IVI Or Obsolete Attributes
- Instrument Capabilities Attributes
- If Digitizer Attributes
NI-XNET
- gRPC API differences from C APIs
- General Functions
- Cluster Properties
- Database Properties
- Device Properties
- ECU Properties
- Frame Properties
- Interface Properties
- LIN Schedule Entry Properties
- LIN Schedule Properties
- PDU Properties
- Session Ethernet Properties
- Session Frame Properties
- Session Interface Properties
- Session Properties
- Session SAE J1939 Properties
- Signal Properties
- Subframe Properties
- System Properties
- IP-Stack Functions
- Socket Options
- Socket Functions