iec62056-lora

Periodically read current power, energy consumption and other OBIS-values from a electricity meter that support the IEC 62056-21 protocol.
Use LoRa/TTN to send the data to a (public or private) gateway
The gateway POST's the data to a Home-Assistant WebHook where the data is applied to several template sensors

State

Project is still work in progress (feel free to contribute)
In the beginning I was experimenting around with the Heltec lora esp32 micro-controller. That micro-controller is fully Arduino / Platformio compatible and work fine as long as you don't wanna power it by a battery as it consumed a lot of energy even in deep-sleep. Thus I switched to the Heltec CubeCell AB02 series that is specialized for battery operated use-cases.
I ran a long dozen of times up and down the staircase (third floor) down to the basement for this project - if you want to avoid that, free to buy me a coffee

My Hardware

Micro Controllers

Heltec Cubecell AB02-A
- Powered by 1/2 AA Battery (Saft LS14250 3.6V)
Heltec Cubecell AB02 Dev Board
~~Heltec lora esp32 v2 Dev Board~~

Others

Installation

Heltec Cubecell AB02 (recommended)

Based on Arduino IDE
Follow the instruction provided here: https://github.com/HelTecAutomation/CubeCell-Arduino#installation-instructions
- The CubeCell Arduino version 1.3.0 has some issues that were fixed but not released as of today. If the version 1.4.0 is not released yet, you have to follow the instructions to install the development repository of the Heltec CubeCell boards in Arduino.
Checkout the project ( directory ./heltec-cubecell ) and open the .ino file in the Arduino IDE

Wiring

Pinout Diagramms:

Board: AB02-A
Board: AB02

Connect as following:

Optical Reading Head: VCC -> VEXT
Optical Reading Head: GND -> GND
Optical Reading Head: RX -> RX2 (GPIO 29)
Optical Reading Head: TX -> TX2 (GPIO 39)

Configuration

Rename credentials_example.h to credentials.h and provide your OTAA data
- I generated random hex values for devEui, appEu and appKey
Select the correct board in the Arduino IDE:
- Tools -> Boards -> CubeCell (in sketchbook) -> HTCC - AB02A
Set the LORAWAN values from within in the Arduino IDE:
- Tools -> LORAWAN_REGION -> your-region (eg. EU_868)
- Tools -> LORAWAN_CLASS -> A
- Tools -> LORAWAN_DEVEUI -> CUSTOM
- Tools -> LORAWAN_NETMODE -> OTAA
- Tools -> AT_SUPPORT -> ON
Check/Adjust the ADJUSTME comments

Debugging / Hints

use the serial monitor in Arduino and change the DEFAULT_LOG_LEVEL to debug in the ino file
- Attention: Make sure once everything works as intended to change it back to Info as too much logging has a negative impact on the power consumption (even if there is not serial monitor connected)
The smart meter is not interacted with as long as the LoRaWAN has not been initialized / OTAA-registered
- uncomment the line deviceState = DEVICE_STATE_SEND in the wakeup procedure to directly read the smart meter data when the on-board user button is pressed without checking/waiting for a successfully LoRaWAN registration
Send a LoRaWan downlink message from your gateway to change the sleep time on demand. The message is read the next time the node wakes up.
```
Port: 4
payload: <desired-sleep-time-seconds-in-hex>  // 04B0 = 1200 seconds  = 20 min
```
Make sure you have a decent LoRaWAN connectivity where your smart-meter is located or nearby by using an extension cord/antenna. I played around with a simple LoRaWAN example sketch from Heltec to find a good spot with a decent connectivity:

Examples -> CubeCell -> LoRa -> LoRaWAN -> LoRaWAN

And then verified in my Lora-Gateway if the messages were received and if so, what their RSSI/SNR data were.

Heltec Wifi LoRA 32 V2 (deprecated)

Based on Platformio
Not suitable for my use-case as it consumed to much power (even in deep-sleep) and thus couldn't get it to operate by battery

Supported Smart Meters

Elster AS3000

SKIP_CHECKSUM_CHECK
METER_IDENTIFIER "ELS"
BAUDRATE_CHANGE_DELAY: 500
PARITY_SETTING SERIAL_7E1 
OBIS_VALUE_POWER "1.7.0 "
OBIS_VALUE_TOTAL_ENERGY "1.8.0"
INITIAL_BAUD_RATE 300
SERIAL_IDENTIFICATION_READING_TIMEOUT 2000
SERIAL_READING_TIMEOUT  500
MAX_METER_READ_TIME  60

Landys&Gyr ZMD120AR21

SKIP_CHECKSUM_CHECK
METER_IDENTIFIER "LGZ"
BAUDRATE_CHANGE_DELAY: 500
PARITY_SETTING SERIAL_7E1 
OBIS_VALUE_POWER "1.7.0 "
OBIS_VALUE_TOTAL_ENERGY "1.8.0"
OBIS_VALUE_TOTAL_ENERGY_TARIFF1 "1.8.1"
OBIS_VALUE_TOTAL_ENERGY_TARIFF2 "1.8.2"
INITIAL_BAUD_RATE 300
SERIAL_IDENTIFICATION_READING_TIMEOUT 2000
SERIAL_READING_TIMEOUT  500
MAX_METER_READ_TIME  60

Acknowledgements

TheThingsNetwork Integration

For TTN we can define a uplink payload formater to convert the data to a be used later in Home-Assistant via MQTT

function decodeUplink(input) {
  return {
    data: {
      bytes: input.bytes,
      power: (input.bytes[0] << 8) + (input.bytes[1]),
      energy: (input.bytes[2] << 24) + (input.bytes[3] << 16) + (input.bytes[4] << 8) + (input.bytes[5]),
      energy1: (input.bytes[6] << 24) + (input.bytes[7] << 16) + (input.bytes[8] << 8) + input.bytes[9],
      energy2: (input.bytes[10] << 24) + (input.bytes[11] << 16) + (input.bytes[12] << 8) + input.bytes[13],
      batteryPCT: input.bytes[14],
      battery:(input.bytes[15] << 8) + input.bytes[16],
      counter: input.bytes[17]
    },
    warnings: [],
    errors: []
  };
}

The coresponding MQQT Sensor in HomeAssistant can be configured like this. Replace APPLICAITON and DEVICE_EUI with the name of you TTN aplication and ID of your device. You can find the required data in the TTN console.

mqtt:
  sensor:
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Kwh"
      unique_id: smart_meter_kwh
      icon: mdi:chart-histogram
      unit_of_measurement: "kWh"
      state_class: total_increasing
      device_class: energy
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.energy | default(none) %}
        {% if value == '00000000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16)/100|float }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Kwh Peak"
      unique_id: smart_meter_kwh_peak
      icon: mdi:chart-histogram
      unit_of_measurement: "kWh"
      state_class: total_increasing
      device_class: energy
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.energy1 | default(none) %}
        {% if value == '00000000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16)/100|float }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Kwh OffPeak"
      unique_id: smart_meter_kwh_offPeak
      icon: mdi:chart-histogram
      unit_of_measurement: "kWh"
      state_class: total_increasing
      device_class: energy
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.energy2 | default(none) %}
        {% if value == '00000000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16)/100|float }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Power"
      unique_id: smart_meter_power
      icon: mdi:flash-outline
      unit_of_measurement: "W"
      state_class: measurement
      device_class: power
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.power | default(none) %}
        {% if value == '0000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Battery"
      unique_id: smart_meter_battery
      icon: mdi:battery
      unit_of_measurement: "%"
      device_class: battery
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.batteryPCT | default(none) %}
        {% if value == '00' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Battery Voltage"
      unique_id: smart_meter_battery_voltage
      icon: mdi:battery
      unit_of_measurement: "mV"
      state_class: measurement
      device_class: battery
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.battery | default(none) %}
        {% if value == '0000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}
    - state_topic: "v3/APPLICATION@ttn/devices/DEVICE_EUI/up"
      name: "Smart Meter Up-Counter"
      unique_id: smart_meter_upcounter
      icon: mdi:counter
      unit_of_measurement: "times"
      value_template: >-
        {% set value = value_json.uplink_message.decoded_payload.counter | default(none) %}
        {% if value == '00' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}

Home-Assistant Template Sensors

- trigger:
    - platform: webhook
      webhook_id: lorawan-data
      id: lorawan-data
  unique_id: smart_meter
  sensor:
    - name: "Smart Meter Power"
      unique_id: smart_meter_power
      icon: mdi:flash-outline
      unit_of_measurement: W
      device_class: power
      state_class: measurement
      state: >-
        {% set payloadHex = trigger.json.data.payload_hex | default(none) %}
        {% set value = payloadHex[0:4] %}
        {% if value == '0000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}

    - name: "Smart Meter Kwh"
      unique_id: smart_meter_kwh
      icon: mdi:chart-histogram
      unit_of_measurement: "kWh"
      state_class: measurement
      device_class: energy
      state: >-
        {% set payloadHex = trigger.json.data.payload_hex | default(none) %}
        {% set value = payloadHex[4:12] %}
        {% if value == '00000000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16)/100|float }}
        {% endif %}

    - name: "Smart Meter Battery"
      unique_id: smart_meter_battery
      icon: mdi:battery
      unit_of_measurement: "%"
      device_class: battery
      state: >-
        {% set payloadHex = trigger.json.data.payload_hex | default(none) %}
        {% set value = payloadHex[12:14] %}
        {% if value == '00' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}

    - name: "Smart Meter Battery Voltage"
      unique_id: smart_meter_battery_voltage
      icon: mdi:battery
      unit_of_measurement: "mV"
      state_class: measurement
      device_class: voltage
      state: >-
        {% set payloadHex = trigger.json.data.payload_hex | default(none) %}
        {% set value = payloadHex[14:18] %}
        {% if value == '0000' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}

    - name: "Smart Meter Up-Counter"
      unique_id: smart_meter_upcounter
      icon: mdi:counter
      unit_of_measurement: "times"
      state: >-
        {% set payloadHex = trigger.json.data.payload_hex | default(none) %}
        {% set value = payloadHex[18:20] %}
        {% if value == '00' %}
          {{ none }}
        {% else %}
          {{ value | int(value,16) }}
        {% endif %}

Name		Name	Last commit message	Last commit date
Latest commit History 29 Commits
.vscode		.vscode
heltec-cubecell		heltec-cubecell
heltec-esp32		heltec-esp32
.gitignore		.gitignore
readme.md		readme.md

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

iec62056-lora

State

My Hardware

Micro Controllers

Others

Installation

Heltec Cubecell AB02 (recommended)

Wiring

Configuration

Debugging / Hints

Heltec Wifi LoRA 32 V2 (deprecated)

Supported Smart Meters

Acknowledgements

TheThingsNetwork Integration

Home-Assistant Template Sensors

About

Releases

Packages

Languages

chriszuercher/iec62056-lora

Folders and files

Latest commit

History

Repository files navigation

iec62056-lora

State

My Hardware

Micro Controllers

Others

Installation

Heltec Cubecell AB02 (recommended)

Wiring

Configuration

Debugging / Hints

Heltec Wifi LoRA 32 V2 (deprecated)

Supported Smart Meters

Acknowledgements

TheThingsNetwork Integration

Home-Assistant Template Sensors

About

Resources

Stars

Watchers

Forks

Releases

Packages 0

Languages

Packages