drivers: hwmon: max31827: add max31875

MAX31875 Low-Power I2C Temperature Sensor

Signed-off-by: John Erasmus Mari Geronimo <[email protected]>

Documentation/hwmon/max31827.rst

@@ -29,9 +29,18 @@ Supported chips:
 
     Datasheet: Publicly available at the Analog Devices website
 
+  * Maxim MAX31875
+
+    Prefix: 'max31875'
+
+    Addresses scanned: I2C 0x48 - 0x4f
+
+    Datasheet: Publicly available at the Analog Devices website
+
 
 Authors:
 	- Daniel Matyas <[email protected]>
+	- John Erasmus Mari Geronimo <[email protected]>
 
 Description
 -----------
@@ -45,13 +54,20 @@ configured to operate in the same manner with 1 write operation to the
 configuration register. From here on, we will refer to all these chips as
 MAX31827.
 
-MAX31827 implements a temperature sensor with a 6 WLP packaging scheme. This
-sensor measures the temperature of the chip itself.
+This driver also supports the MAX31875. Its fault queue is set to 1 and it has
+no alarm polarity.
+
+MAX31827 implements a temperature sensor with a 6 WLP packaging scheme while
+MAX31875 has a 4 WLP packaging scheme. This sensor measures the temperature of
+the chip itself.
 
 MAX31827 has low and over temperature alarms with an effective value and a
 hysteresis value: -40 and -30 degrees for under temperature alarm and +100 and
 +90 degrees for over temperature alarm.
 
+MAX31875 has only an over temperature alarm with an effective value and a
+hysteresis value: +80 and +75 degrees.
+
 The alarm can be configured in comparator and interrupt mode from the
 devicetree. In Comparator mode, the OT/UT status bits have a value of 1 when the
 temperature rises above the TH value or falls below TL, which is also subject to
@@ -75,19 +91,22 @@ it is recommended to perform a read of the configuration/status register to
 clear the status bits before changing the operating mode.
 
 The conversions can be manual with the one-shot functionality and automatic with
-a set frequency. When powered on, the chip measures temperatures with 1 conv/s.
+a set frequency. When powered on, the MAX31827 measures temperatures with 1
+conv/s while the MAX31875 measures temperatures with 0.25 conv/s or 1 conv/4s.
 The conversion rate can be modified with update_interval attribute of the chip.
 Conversion/second = 1/update_interval. Thus, the available options according to
 the data sheet are:
 
 - 64000 (ms) = 1 conv/64 sec
 - 32000 (ms) = 1 conv/32 sec
 - 16000 (ms) = 1 conv/16 sec
-- 4000 (ms) = 1 conv/4 sec
-- 1000 (ms) = 1 conv/sec (default)
+- 4000 (ms) = 1 conv/4 sec (MAX31875 default)
+- 1000 (ms) = 1 conv/sec (MAX31827 default)
 - 250 (ms) = 4 conv/sec
 - 125 (ms) = 8 conv/sec
 
+The MAX31875 only supports the last four values above.
+
 Enabling the device when it is already enabled has the side effect of setting
 the conversion frequency to 1 conv/s. The conversion time varies depending on
 the resolution.
@@ -97,16 +116,16 @@ available resolutions are:
 
 - 8 bit -> 8.75 ms conversion time
 - 9 bit -> 17.5 ms conversion time
-- 10 bit -> 35 ms conversion time
-- 12 bit (default) -> 140 ms conversion time
+- 10 bit (MAX31875 default) -> 35 ms conversion time
+- 12 bit (MAX31827 default) -> 140 ms conversion time
 
 There is a temp1_resolution attribute which indicates the unit change in the
 input temperature in milli-degrees C.
 
 - 1000 mC -> 8 bit
 - 500 mC -> 9 bit
-- 250 mC -> 10 bit
-- 62 mC -> 12 bit (default) - actually this is 62.5, but the fil returns 62
+- 250 mC -> 10 bit (MAX31875 default)
+- 62 mC -> 12 bit (MAX31827 default) - actually this is 62.5, but the fil returns 62
 
 When chip is in shutdown mode and a read operation is requested, one-shot is
 triggered, the device waits for <conversion time> ms, and only after that is
@@ -125,7 +144,8 @@ Bus timeout resets the I2C-compatible interface when SCL is low for more than
 
 Alarm polarity determines if the active state of the alarm is low or high. The
 behavior for both settings is dependent on the Fault Queue setting. The ALARM
-pin is an open-drain output and requires a pullup resistor to operate.
+pin is an open-drain output and requires a pullup resistor to operate. The
+MAX31875 does not have this feature.
 
 The Fault Queue bits select how many consecutive temperature faults must occur
 before overtemperature or undertemperature faults are indicated in the