Skip to content

Integration

Jump to bottom
Ilya Baldin edited this page Aug 24, 2024 · 27 revisions

Integration with EJFAT dataplane and control plane

Overview

E2SAR uses a combination of UDP packets and gRPC+TLS to communicate with loadbalancer control plane and dataplane.

All interactions are captured in the figure above.

The process of using the load balancer begins with (1) reserving a load balancer using an out-of-band information like the admin token and the ejfat URL of the Control Plane agent. This can be done by one of the receivers or by Workflow Management System (WMS) or its proxy.

Once the load balancer is reserved and the details of the reservation communicated out of band (shown with dotted lines) to the worker nodes, they can register themselves with the control plane (2). Alternatively the registration can be peformed by WMS or its proxy assuming the details of the workers are known to it.

At this point (after all workers have been registered and the details of the load balancer communicated to the sender(s) - shown with dotted lines) data can begin traversing the dataplane in segments (3a and 3b).

Periodic sync messages (4) are required to be sent by the sender once a second. Similarly the receiving nodes or WMS on their behalf must periodically use SendState gRPC call (5) to update queue occupancy information in the control plane.

After the workflow completes, the workers can be deregistered (6) - themselves or via WMS. The load balancer can be freed (7).

In addition at any time someone with admin token can request repeat reservation reply via GetLoadBalancer call (X), get detailed information about load balancer and its worker node clients via LoadBalancerStatus (Y) and get an overview of all provisioned load balancers and their associated worker node clients via Overview call (Z).

E2SAR and Control Plane Messaging

EJFAT_URI formats

EJFAT defines its own URI format to convey necessary information to different actors in different phases of the workflow. The general format of the URI is:

ejfat[s]://[<token>@]<cp_host>:<cp_port>/[lb/<lb_id>][?[data=<data_host:[<data_port>]>][&sync=<sync_host>:<sync_port>][&sessionid=<session_id>]].

Where:

  • ejfat or ejfats is the schema name, with ejfats requiring the use of TLS when speaking gRPC to the Control Plane (CP)
  • token is either admin, instance or session token, depending on the context (discussed below) needed to communicate over gRPC (it is not used for any other communications)
  • cp_host:cp_port is either an address or a name of the CP gRPC server and the port it is listening on
  • lb_id is the identifier of the virtual load balancer that was reserved (discussed below)
  • data_host and optional data_port are the address (hostnames are not allowed) of the Load Balancer - this is where the segments of events are sent to. When not specified, data_port defaults to 19522. Tyically the URI may contain two data= elements - one specifying IPv4 and the other - IPv6 address of the Load Balancer.
  • sync_addr:sync_port is the address of the Control Plane where UDP Sync packets must be sent by the sending site. Note that this is not required to be the same as the hostname or address used for gRPC communications.
  • session_id is the session ID issued when a worker is registered, see discussion below.

Different control plane commands use different portions of the EJFAT URI and this section attempts to explain which portions of the URI is relevant at different stages as it relates to the diagram above.

Step 1 (ReserveLoadBalancer): ejfat[s]://<admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/

Step 2 (Register worker node): ejfat[s]://<instance or admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>

  • instance token and lbid come from Step 1
  • Note that can be done from worker node or centrally by the WMS

Steps 3a, 3b4, 7, and 8 (Sender sending data and sync packets and using AddSender/RemoveSender gRPC): ejfat[s]://<instance or admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>?sync=<sync IP address>:<sync UDP port>&data=<data IPv4>[&data=<data IPv6>]

  • Note that instance token and CP name and address and lb id aren't actually used, unless the uses Steps 7,8 Add/Remove sender gRPC calls
  • Note that up to two dataplane addresses of the loadbalancer (where to send the data) can be specified - an IPv4 and an IPv6 address
  • Note that 7 and 8 (addSenders/removeSenders) can be done from sender or centrally by the WMS

Step 5 (SendState from worker node): ejfat[s]://<session or instance token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>?sessionid=<session id>

  • session id and session token come from the return of Step 2
  • sync and data addresses are not relevant

Step 6 (Deregister worker): ejfat[s]://<session or admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>?sessionid=<session id>

  • session id and session token come from Step 2
  • sync and data addresses are not relevant
  • Note that can be done from worker node or centrally by WMS

Step 9 (FreeLoadBalancer): ejfat[s]://<admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>/

Steps X and Y (GetLoadBalancer and LoadBalancerStatus): ejfat[s]://<instance or admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/lb/<lbid>

  • instance token and lbid come from Step 1

Step Z (Overview): ejfat[s]://<admin token>@<cp name or IPv4 or IPv6 address>:<cp port>/

  • same as in Step 1

Note that EjfatURI object in the code can maintain multiple tokens internally and it knows which token to use in which sitation when using gRPC. Classes Segmenter and Reassembler also know how to ask EjfatURI object for the information they need. When loading a new EjfatURI object from a URI string (or environment variable) the constructor has a flag telling the object how to interpret the passed in token (admin, instance or session).

Token administrative domains and security information flows

EJFAT presumes multiple deployment options with different administrative entities being potentially responsible for managing a load-balancer farm, instances of virtual loadbalancers instantiated on that farm and even individual worker nodes communicating with a specific previously provisioned LB instance. The figure below attempts to capture these possibilities.

The authority to perform certain operations is rooted in the possession of an admin, instance or session token.

AJFAT Authority flows

Timings and other message rules

EJFAT Control plane has a few timing rules and best practices for implementation:

  • Sync messages should be sent about 1 time per second by the sender (can be more often). The control plane uses a ringbuffer to calculate the rate slope. E2SAR also includes a low-pass filter for this purpose (you can set the sync period and the number of sync periods over which the reported rate is computed).
  • After a worker is registered, sendState must be sent within 10 seconds. In general a period of 100ms is recommended for doing sendState
  • When reserving a load balancer with reserveLB if the passed in duration time is 0 (i.e. UNIX epoc) the reservation never expires.

Additional Information

Additional details are contained in this document

Clone this wiki locally