LibreRouter V1 - Vailla LEDE flash issue

[darkdrgn2k]

Seems the LibreRouter V1 running Vanilla LEDE seems to break the the kernel partition

root@LiMe-112ed8:/tmp# sysupgrade -n openwrt-lede-vanilla-ar71xx-generic-librero
uter-v1-squashfs-sysupgrade.bin
Image metadata not found
killall: watchdog: no process killed
Commencing upgrade. All shell sessions will be closed now.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... ntpd udhcpc alfred batadv-vis hostapd [  285.926731] br-lan: port 4(wlan0-apname) entered disabled state
watchping watchping [  285.949944] device wlan0-apname left promiscuous mode
[  285.955087] br-lan: port 4(wlan0-apname) entered disabled state
dnsmasq dnsmasq sleep sleep ubusd logd rpcd netifd crond netserver [  286.155504] device wlan0-ap left promiscuous mode
[  286.160408] br-lan: port 3(wlan0-ap) entered disabled state
uhttpd bmx6
Sending KILL to remaining processes ... ntpd
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system...
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[  312.677253] reboot: Restarting system
�

U-Boot 1.1.4 (Apr 19 2014 - 00:17:22)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(200): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x5, 0x1d)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 207k for U-Boot at: 87fcc000
Reserving 192k for malloc() at: 87f9c000
Reserving 44 Bytes for Board Info at: 87f9bfd4
Reserving 36 Bytes for Global Data at: 87f9bfb0
Reserving 128k for boot params() at: 87f7bfb0
Stack Pointer at: 87f7bf98
Now running in RAM - U-Boot at: 87fcc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning *** : PCIe WLAN Module not found !!!
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial   
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
Fetching MAC Address from 0x87feea5c
Fetching MAC Address from 0x87feea5c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> S17 PHY *
Vlan config...
s17 phy0 register value 0x00004140
TEST: FINAL REG VAL after TX Calibration - 0x4a000000
TEST: FINAL XMII VAL after RX Calibration - 0x4a000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: 00:03:7f:11:2e:d8
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:11:2e:d9
eth1 up
eth0, eth1
Setting 0x18116290 to 0x50a0214f
Hit any key to stop autoboot:  0
## Booting image at 9fe80000 ...
   Image Name:   MIPS OpenWrt Linux-4.9.67
   Created:      2018-07-03  17:22:27 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1415695 Bytes =  1.4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9fe80040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.9.67 (lime@compile) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 r5544-d9245c4) ) #0 Wed Dec 27 21:01:14 2017
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] OF: fdt:No valid device tree found, continuing without
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: board=LIBREROUTERV1 console=ttyS0,115200 mem=128M rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124744K/131072K available (3247K kernel code, 165K rwdata, 824K rodata, 300K init, 213K bss, 6328K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008293] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.071187] pid_max: default: 32768 minimum: 301
[    0.076183] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.083221] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092628] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.103124] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.110048] NET: Registered protocol family 16
[    0.115930] MIPS: machine is LibreRouter v1
[    0.597974] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.603442] registering PCI controller with io_map_base unset
[    0.609680] ar724x-pci ar724x-pci.1: PCIe link is down
[    0.615140] registering PCI controller with io_map_base unset
[    0.632043] PCI host bridge to bus 0000:00
[    0.636410] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.643754] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.649674] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.656898] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.665436] PCI host bridge to bus 0000:01
[    0.669815] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[    0.677124] pci_bus 0000:01: root bus resource [io  0x0001]
[    0.683054] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.690270] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.699260] clocksource: Switched to clocksource MIPS
[    0.705460] NET: Registered protocol family 2
[    0.710755] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.718173] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.724978] TCP: Hash tables configured (established 1024 bind 1024)
[    0.731815] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.738034] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.744919] NET: Registered protocol family 1
[    0.752857] Crashlog allocated RAM at address 0x3f00000
[    0.759158] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.771487] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.777686] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.794658] io scheduler noop registered
[    0.798829] io scheduler deadline registered (default)
[    0.804657] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.811789] console [ttyS0] disabled
[    0.835656] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.844837] console [ttyS0] enabled
[    0.844837] console [ttyS0] enabled
[    0.852254] bootconsole [early0] disabled
[    0.852254] bootconsole [early0] disabled
[    0.863611] m25p80 spi0.0: found w25q128, expected w25q256
[    0.869185] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.873994] Creating 4 MTD partitions on "spi0.0":
[    0.878865] 0x000000000000-0x000000040000 : "uboot"
[    0.885374] 0x000000040000-0x000000050000 : "uboot-env"
[    0.891964] 0x000000050000-0x000000ff0000 : "firmware"
[    0.931380] 2 uimage-fw partitions found on MTD device firmware
[    0.937396] 0x000000050000-0x0000001b0000 : "kernel"
[    0.943506] 0x0000001b0000-0x000000ff0000 : "rootfs"
[    0.949822] mtd: device 4 (rootfs) set to be root filesystem
[    0.955604] 1 squashfs-split partitions found on MTD device rootfs
[    0.961916] 0x000000380000-0x000000ff0000 : "rootfs_data"
[    0.968650] 0x000000ff0000-0x000001000000 : "art"
[    0.975459] libphy: Fixed MDIO Bus: probed
[    0.991889] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.677558] libphy: ag71xx_mdio: probed
[    2.310762] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.322113] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.599255] random: fast init done
[    2.950868] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[    2.958018] NET: Registered protocol family 10
[    2.964844] NET: Registered protocol family 17
[    2.969434] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.982669] 8021q: 802.1Q VLAN Support v1.8
[    2.993105] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    3.001374] Freeing unused kernel memory: 300K
[    3.005879] This architecture does not have kernel memory protection.
[    3.804775] init: Console is alive
[    3.808383] init: - watchdog -
[    4.648505] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.778635] usbcore: registered new interface driver usbfs
[    4.784326] usbcore: registered new interface driver hub
[    4.789817] usbcore: registered new device driver usb
[    4.799038] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.806946] ehci-platform: EHCI generic platform driver
[    4.812367] ehci-platform ehci-platform.0: EHCI Host Controller
[    4.818406] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    4.828679] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[    4.834792] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    4.869276] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.876485] hub 1-0:1.0: USB hub found
[    4.880562] hub 1-0:1.0: 1 port detected
[    4.884843] ehci-platform ehci-platform.1: EHCI Host Controller
[    4.890909] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    4.901203] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[    4.907302] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    4.939271] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[    4.946476] hub 2-0:1.0: USB hub found
[    4.950561] hub 2-0:1.0: 1 port detected
[    4.955148] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.972857] init: - preinit -
[    5.647300] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.659320] usb 1-1: new high-speed USB device number 2 using ehci-platform
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    5.861221] hub 1-1:1.0: USB hub found
[    5.865289] hub 1-1:1.0: 4 ports detected
[    6.680692] eth0: link up (1000Mbps/Full duplex)
[    6.685513] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.766961] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    8.792714] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.952342] eth0: link down
[    8.964278] procd: - early -
[    8.967278] procd: - watchdog -
[    9.512763] procd: - watchdog -
[    9.516148] procd: - ubus -
[    9.570558] procd: - init -
Please press Enter to activate this console.
[    9.883284] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.893387] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.907490] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    9.915653] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    9.924792] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.936607] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    9.998611] xt_time: kernel timezone is -0000
[   10.047926] PPP generic driver version 2.4.2
[   10.054273] NET: Registered protocol family 24
[   10.113243] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[   10.209424] kmodloader: done loading kernel modules from /etc/modules.d/*



BusyBox v1.27.2 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r5577+2-6325eee
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# [   15.944792] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   15.979312] jffs2_build_filesystem(): unlocking the mtd device... [   15.985416] done.
[   15.987367] jffs2_build_filesystem(): erasing all blocks after the end marker... [   19.924024] eth1: link up (1000Mbps/Full duplex)
[   19.955777] br-lan: port 1(eth1.2) entered blocking state
[   19.961409] br-lan: port 1(eth1.2) entered disabled state
[   19.967189] device eth1.2 entered promiscuous mode
[   19.972091] device eth1 entered promiscuous mode
[   20.055728] br-lan: port 1(eth1.2) entered blocking state
[   20.061244] br-lan: port 1(eth1.2) entered forwarding state
[   20.145844] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.180183] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   21.160730] eth0: link up (1000Mbps/Full duplex)
[   21.165550] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.215973] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready

[   67.341363] jffs2: notice: (860) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.



root@OpenWrt:/# reboot
root@OpenWrt:/# [  129.329646] br-lan: port 1(eth1.2) entered disabled state
[  129.350086] device eth1.2 left promiscuous mode
[  129.354683] device eth1 left promiscuous mode
[  129.359203] br-lan: port 1(eth1.2) entered disabled state
[  129.369939] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[  129.382124] eth1: link down
[  133.645475] Removing MTD device #5 (rootfs_data) with use count 1
[  133.661399] reboot: Restarting system
�

U-Boot 1.1.4 (Apr 19 2014 - 00:17:22)

ap135 - Scorpion 1.0DRAM:
sri  
Scorpion 1.0
ath_ddr_initial_config(200): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x5, 0x1e)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 207k for U-Boot at: 87fcc000
Reserving 192k for malloc() at: 87f9c000
Reserving 44 Bytes for Board Info at: 87f9bfd4
Reserving 36 Bytes for Global Data at: 87f9bfb0
Reserving 128k for boot params() at: 87f7bfb0
Stack Pointer at: 87f7bf98
Now running in RAM - U-Boot at: 87fcc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning *** : PCIe WLAN Module not found !!!
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
Fetching MAC Address from 0x87feea5c
Fetching MAC Address from 0x87feea5c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> S17 PHY *
Vlan config...
s17 phy0 register value 0x00004140
TEST: FINAL REG VAL after TX Calibration - 0x4a000000
TEST: FINAL XMII VAL after RX Calibration - 0x4a000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: 00:03:7f:11:2e:d8
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:11:2e:d9
eth1 up
eth0, eth1
Setting 0x18116290 to 0x50a0214f
Hit any key to stop autoboot:  0
## Booting image at 9fe80000 ...
Bad Magic Number
ath> 

After re flashing the kernel jffs2_scan_eraseblock() seems to break it agian

[    8.791757] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00000: 0x2705 instead
[    8.801384] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00004: 0x02ec instead
[    8.811073] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00008: 0x5b3e instead
[    8.820697] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b0000c: 0x0015 instead
[    8.830322] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00010: 0x8006 instead
[    8.839941] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00014: 0x8006 instead
[    8.849560] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00018: 0x32e4 instead
[    8.859171] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b0001c: 0x0505 instead
[    8.868788] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00020: 0x4d49 instead
[    8.878406] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b00024: 0x204f instead
[    8.888021] jffs2: Further such events for this erase block will not be printed
[    8.942542] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10000: 0x2199 instead
[    8.952161] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10004: 0x15b4 instead
[    8.961777] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10008: 0x2196 instead
[    8.971395] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b1000c: 0x440a instead
[    8.981013] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10010: 0x51d2 instead
[    8.990632] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10014: 0x88bd instead
[    9.000256] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10018: 0x22ac instead
[    9.009870] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b1001c: 0x6a85 instead
[    9.019487] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10020: 0x8b34 instead
[    9.029099] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b10024: 0xd87d instead
[    9.038715] jffs2: Further such events for this erase block will not be printed
[    9.093222] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20000: 0xf4a8 instead
[    9.102843] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20004: 0x6fae instead
[    9.112460] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20008: 0xcb03 instead
[    9.122077] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b2000c: 0x65c2 instead
[    9.131696] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20010: 0xffee instead
[    9.141318] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20014: 0xf45e instead
[    9.150932] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20018: 0x42d4 instead
[    9.160551] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b2001c: 0xadd6 instead
[    9.170170] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20020: 0xd9ed instead
[    9.179788] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b20024: 0x87f1 instead
[    9.189402] jffs2: Further such events for this erase block will not be printed
[    9.243899] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30000: 0xe821 instead
[    9.253517] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30004: 0x6af4 instead
[    9.263132] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30008: 0xfc87 instead
[    9.272751] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b3000c: 0x6120 instead
[    9.282369] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30010: 0x607e instead
[    9.291988] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30014: 0x046a instead
[    9.301606] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30018: 0xe988 instead
[    9.311224] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b3001c: 0xc3a5 instead
[    9.320843] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30020: 0xe635 instead
[    9.330461] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b30024: 0xe122 instead
[    9.340075] jffs2: Further such events for this erase block will not be printed
[    9.394571] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b40000: 0xa30b instead
[    9.404190] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b40004: 0x2160 instead
[    9.413806] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00b40008: 0x14d8 instead

[darkdrgn2k]

NOTE
Eth 1 Works
Eth 0 Does not