forked from allwinner-ics/lichee_u-boot
-
Notifications
You must be signed in to change notification settings - Fork 2
/
README
4614 lines (3544 loc) · 156 KB
/
README
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
#
# (C) Copyright 2000 - 2011
# Wolfgang Denk, DENX Software Engineering, [email protected].
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
Summary:
========
This directory contains the source code for U-Boot, a boot loader for
Embedded boards based on PowerPC, ARM, MIPS and several other
processors, which can be installed in a boot ROM and used to
initialize and test the hardware or to download and run application
code.
The development of U-Boot is closely related to Linux: some parts of
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
support booting of Linux images.
Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.
Status:
=======
In general, all boards for which a configuration option exists in the
Makefile have been tested to some extent and can be considered
"working". In fact, many of them are used in production systems.
In case of problems see the CHANGELOG and CREDITS files to find out
who contributed the specific port. The MAINTAINERS file lists board
maintainers.
Where to get help:
==================
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
<[email protected]>. There is also an archive of previous traffic
on the mailing list - please search the archive before asking FAQ's.
Please see http://lists.denx.de/pipermail/u-boot and
http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
Where to get source code:
=========================
The U-Boot source code is maintained in the git repository at
git://www.denx.de/git/u-boot.git ; you can browse it online at
http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
The "snapshot" links on this page allow you to download tarballs of
any version you might be interested in. Official releases are also
available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
directory.
Pre-built (and tested) images are available from
ftp://ftp.denx.de/pub/u-boot/images/
Where we come from:
===================
- start from 8xxrom sources
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
* Provide extended interface to Linux boot loader
* S-Record download
* network boot
* PCMCIA / CompactFlash / ATA disk / SCSI ... boot
- create ARMBoot project (http://sourceforge.net/projects/armboot)
- add other CPU families (starting with ARM)
- create U-Boot project (http://sourceforge.net/projects/u-boot)
- current project page: see http://www.denx.de/wiki/U-Boot
Names and Spelling:
===================
The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:
This is the README file for the U-Boot project.
File names etc. shall be based on the string "u-boot". Examples:
include/asm-ppc/u-boot.h
#include <asm/u-boot.h>
Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:
U_BOOT_VERSION u_boot_logo
IH_OS_U_BOOT u_boot_hush_start
Versioning:
===========
Starting with the release in October 2008, the names of the releases
were changed from numerical release numbers without deeper meaning
into a time stamp based numbering. Regular releases are identified by
names consisting of the calendar year and month of the release date.
Additional fields (if present) indicate release candidates or bug fix
releases in "stable" maintenance trees.
Examples:
U-Boot v2009.11 - Release November 2009
U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
Directory Hierarchy:
====================
/arch Architecture specific files
/arm Files generic to ARM architecture
/cpu CPU specific files
/arm720t Files specific to ARM 720 CPUs
/arm920t Files specific to ARM 920 CPUs
/at91 Files specific to Atmel AT91RM9200 CPU
/imx Files specific to Freescale MC9328 i.MX CPUs
/s3c24x0 Files specific to Samsung S3C24X0 CPUs
/arm925t Files specific to ARM 925 CPUs
/arm926ejs Files specific to ARM 926 CPUs
/arm1136 Files specific to ARM 1136 CPUs
/ixp Files specific to Intel XScale IXP CPUs
/pxa Files specific to Intel XScale PXA CPUs
/s3c44b0 Files specific to Samsung S3C44B0 CPUs
/sa1100 Files specific to Intel StrongARM SA1100 CPUs
/lib Architecture specific library files
/avr32 Files generic to AVR32 architecture
/cpu CPU specific files
/lib Architecture specific library files
/blackfin Files generic to Analog Devices Blackfin architecture
/cpu CPU specific files
/lib Architecture specific library files
/x86 Files generic to x86 architecture
/cpu CPU specific files
/lib Architecture specific library files
/m68k Files generic to m68k architecture
/cpu CPU specific files
/mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
/mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
/mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
/mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
/mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
/lib Architecture specific library files
/microblaze Files generic to microblaze architecture
/cpu CPU specific files
/lib Architecture specific library files
/mips Files generic to MIPS architecture
/cpu CPU specific files
/mips32 Files specific to MIPS32 CPUs
/lib Architecture specific library files
/nios2 Files generic to Altera NIOS2 architecture
/cpu CPU specific files
/lib Architecture specific library files
/powerpc Files generic to PowerPC architecture
/cpu CPU specific files
/74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
/mpc5xx Files specific to Freescale MPC5xx CPUs
/mpc5xxx Files specific to Freescale MPC5xxx CPUs
/mpc8xx Files specific to Freescale MPC8xx CPUs
/mpc8220 Files specific to Freescale MPC8220 CPUs
/mpc824x Files specific to Freescale MPC824x CPUs
/mpc8260 Files specific to Freescale MPC8260 CPUs
/mpc85xx Files specific to Freescale MPC85xx CPUs
/ppc4xx Files specific to AMCC PowerPC 4xx CPUs
/lib Architecture specific library files
/sh Files generic to SH architecture
/cpu CPU specific files
/sh2 Files specific to sh2 CPUs
/sh3 Files specific to sh3 CPUs
/sh4 Files specific to sh4 CPUs
/lib Architecture specific library files
/sparc Files generic to SPARC architecture
/cpu CPU specific files
/leon2 Files specific to Gaisler LEON2 SPARC CPU
/leon3 Files specific to Gaisler LEON3 SPARC CPU
/lib Architecture specific library files
/api Machine/arch independent API for external apps
/board Board dependent files
/common Misc architecture independent functions
/disk Code for disk drive partition handling
/doc Documentation (don't expect too much)
/drivers Commonly used device drivers
/examples Example code for standalone applications, etc.
/fs Filesystem code (cramfs, ext2, jffs2, etc.)
/include Header Files
/lib Files generic to all architectures
/libfdt Library files to support flattened device trees
/lzma Library files to support LZMA decompression
/lzo Library files to support LZO decompression
/net Networking code
/post Power On Self Test
/rtc Real Time Clock drivers
/tools Tools to build S-Record or U-Boot images, etc.
Software Configuration:
=======================
Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.
There are two classes of configuration variables:
* Configuration _OPTIONS_:
These are selectable by the user and have names beginning with
"CONFIG_".
* Configuration _SETTINGS_:
These depend on the hardware etc. and should not be meddled with if
you don't know what you're doing; they have names beginning with
"CONFIG_SYS_".
Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.
Selection of Processor Architecture and Board Type:
---------------------------------------------------
For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".
Example: For a TQM823L module type:
cd u-boot
make TQM823L_config
For the Cogent platform, you need to specify the CPU type as well;
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.
Configuration Options:
----------------------
Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".
Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.
The following options need to be configured:
- CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
Define exactly one, e.g. CONFIG_ATSTK1002
- CPU Module Type: (if CONFIG_COGENT is defined)
Define exactly one of
CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
CONFIG_CMA287_23, CONFIG_CMA287_50
- Motherboard Type: (if CONFIG_COGENT is defined)
Define exactly one of
CONFIG_CMA101, CONFIG_CMA102
- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
Define one or more of
CONFIG_CMA302
- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
Define one or more of
CONFIG_LCD_HEARTBEAT - update a character position on
the LCD display every second with
a "rotator" |\-/|\-/
- Board flavour: (if CONFIG_MPC8260ADS is defined)
CONFIG_ADSTYPE
Possible values are:
CONFIG_SYS_8260ADS - original MPC8260ADS
CONFIG_SYS_8266ADS - MPC8266ADS
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
- Marvell Family Member
CONFIG_SYS_MVFS - define it if you want to enable
multiple fs option at one time
for marvell soc family
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
- 8xx CPU Options: (if using an MPC8xx CPU)
CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
get_gclk_freq() cannot work
e.g. if there is no 32KHz
reference PIT/RTC clock
CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
or XTAL/EXTAL)
- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
CONFIG_SYS_8xx_CPUCLK_MIN
CONFIG_SYS_8xx_CPUCLK_MAX
CONFIG_8xx_CPUCLK_DEFAULT
See doc/README.MPC866
CONFIG_SYS_MEASURE_CPUCLK
Define this to measure the actual CPU clock instead
of relying on the correctness of the configured
values. Mostly useful for board bringup to make sure
the PLL is locked at the intended frequency. Note
that this requires a (stable) reference clock (32 kHz
RTC clock or CONFIG_SYS_8XX_XIN)
CONFIG_SYS_DELAYED_ICACHE
Define this option if you want to enable the
ICache only when Code runs from RAM.
- 85xx CPU Options:
CONFIG_SYS_FSL_TBCLK_DIV
Defines the core time base clock divider ratio compared to the
system clock. On most PQ3 devices this is 8, on newer QorIQ
devices it can be 16 or 32. The ratio varies from SoC to Soc.
CONFIG_SYS_FSL_PCIE_COMPAT
Defines the string to utilize when trying to match PCIe device
tree nodes for the given platform.
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
Defines the Monahans run mode to oscillator
ratio. Valid values are 8, 16, 24, 31. The core
frequency is this value multiplied by 13 MHz.
CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
Defines the Monahans turbo mode to oscillator
ratio. Valid values are 1 (default if undefined) and
2. The core frequency as calculated above is multiplied
by this value.
- MIPS CPU options:
CONFIG_SYS_INIT_SP_OFFSET
Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
pointer. This is needed for the temporary stack before
relocation.
CONFIG_SYS_MIPS_CACHE_MODE
Cache operation mode for the MIPS CPU.
See also arch/mips/include/asm/mipsregs.h.
Possible values are:
CONF_CM_CACHABLE_NO_WA
CONF_CM_CACHABLE_WA
CONF_CM_UNCACHED
CONF_CM_CACHABLE_NONCOHERENT
CONF_CM_CACHABLE_CE
CONF_CM_CACHABLE_COW
CONF_CM_CACHABLE_CUW
CONF_CM_CACHABLE_ACCELERATED
CONFIG_SYS_XWAY_EBU_BOOTCFG
Special option for Lantiq XWAY SoCs for booting from NOR flash.
See also arch/mips/cpu/mips32/start.S.
CONFIG_XWAY_SWAP_BYTES
Enable compilation of tools/xway-swap-bytes needed for Lantiq
XWAY SoCs for booting from NOR flash. The U-Boot image needs to
be swapped if a flash programmer is used.
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
U-Boot stores all clock information in Hz
internally. For binary compatibility with older Linux
kernels (which expect the clocks passed in the
bd_info data to be in MHz) the environment variable
"clocks_in_mhz" can be defined so that U-Boot
converts clock data to MHZ before passing it to the
Linux kernel.
When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
"clocks_in_mhz=1" is automatically included in the
default environment.
CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
When transferring memsize parameter to linux, some versions
expect it to be in bytes, others in MB.
Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
CONFIG_OF_LIBFDT
New kernel versions are expecting firmware settings to be
passed using flattened device trees (based on open firmware
concepts).
CONFIG_OF_LIBFDT
* New libfdt-based support
* Adds the "fdt" command
* The bootm command automatically updates the fdt
OF_CPU - The proper name of the cpus node (only required for
MPC512X and MPC5xxx based boards).
OF_SOC - The proper name of the soc node (only required for
MPC512X and MPC5xxx based boards).
OF_TBCLK - The timebase frequency.
OF_STDOUT_PATH - The path to the console device
boards with QUICC Engines require OF_QE to set UCC MAC
addresses
CONFIG_OF_BOARD_SETUP
Board code has addition modification that it wants to make
to the flat device tree before handing it off to the kernel
CONFIG_OF_BOOT_CPU
This define fills in the correct boot CPU in the boot
param header, the default value is zero if undefined.
CONFIG_OF_IDE_FIXUP
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
This setting is mandatory for all boards that have only one
machine type and must be used to specify the machine type
number as it appears in the ARM machine registry
(see http://www.arm.linux.org.uk/developer/machines/).
Only boards that have multiple machine types supported
in a single configuration file and the machine type is
runtime discoverable, do not have to use this setting.
- vxWorks boot parameters:
bootvx constructs a valid bootline using the following
environments variables: bootfile, ipaddr, serverip, hostname.
It loads the vxWorks image pointed bootfile.
CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
CONFIG_SYS_VXWORKS_ADD_PARAMS
Add it at the end of the bootline. E.g "u=username pw=secret"
Note: If a "bootargs" environment is defined, it will overwride
the defaults discussed just above.
- Cache Configuration:
CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
- Cache Configuration for ARM:
CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
controller
CONFIG_SYS_PL310_BASE - Physical base address of PL310
controller register space
- Serial Ports:
CONFIG_PL010_SERIAL
Define this if you want support for Amba PrimeCell PL010 UARTs.
CONFIG_PL011_SERIAL
Define this if you want support for Amba PrimeCell PL011 UARTs.
CONFIG_PL011_CLOCK
If you have Amba PrimeCell PL011 UARTs, set this variable to
the clock speed of the UARTs.
CONFIG_PL01x_PORTS
If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
CONFIG_PL011_SERIAL_RLCR
Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers. Set
this variable to initialize the extra register.
CONFIG_PL011_SERIAL_FLUSH_ON_INIT
On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
- Console Interface:
Depending on board, define exactly one serial port
(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
console by defining CONFIG_8xx_CONS_NONE
Note: if CONFIG_8xx_CONS_NONE is defined, the serial
port routines must be defined elsewhere
(i.e. serial_init(), serial_getc(), ...)
CONFIG_CFB_CONSOLE
Enables console device for a color framebuffer. Needs following
defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
(default big endian)
VIDEO_HW_RECTFILL graphic chip supports
rectangle fill
(cf. smiLynxEM)
VIDEO_HW_BITBLT graphic chip supports
bit-blit (cf. smiLynxEM)
VIDEO_VISIBLE_COLS visible pixel columns
(cols=pitch)
VIDEO_VISIBLE_ROWS visible pixel rows
VIDEO_PIXEL_SIZE bytes per pixel
VIDEO_DATA_FORMAT graphic data format
(0-5, cf. cfb_console.c)
VIDEO_FB_ADRS framebuffer address
VIDEO_KBD_INIT_FCT keyboard int fct
(i.e. i8042_kbd_init())
VIDEO_TSTC_FCT test char fct
(i.e. i8042_tstc)
VIDEO_GETC_FCT get char fct
(i.e. i8042_getc)
CONFIG_CONSOLE_CURSOR cursor drawing on/off
(requires blink timer
cf. i8042.c)
CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
CONFIG_CONSOLE_TIME display time/date info in
upper right corner
(requires CONFIG_CMD_DATE)
CONFIG_VIDEO_LOGO display Linux logo in
upper left corner
CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
linux_logo.h for logo.
Requires CONFIG_VIDEO_LOGO
CONFIG_CONSOLE_EXTRA_INFO
additional board info beside
the logo
When CONFIG_CFB_CONSOLE is defined, video console is
default i/o. Serial console can be forced with
environment 'console=serial'.
When CONFIG_SILENT_CONSOLE is defined, all console
messages (by U-Boot and Linux!) can be silenced with
the "silent" environment variable. See
doc/README.silent for more information.
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CONFIG_SYS_BAUDRATE_TABLE, see below.
CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
- Console Rx buffer length
With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
the maximum receive buffer length for the SMC.
This option is actual only for 82xx and 8xx possible.
If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
must be defined, to setup the maximum idle timeout for
the SMC.
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
See doc/README.autoboot for these options that
work with CONFIG_BOOTDELAY. None are required.
CONFIG_BOOT_RETRY_TIME
CONFIG_BOOT_RETRY_MIN
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
CONFIG_AUTOBOOT_DELAY_STR2
CONFIG_AUTOBOOT_STOP_STR2
CONFIG_ZERO_BOOTDELAY_CHECK
CONFIG_RESET_TO_RETRY
- Autoboot Command:
CONFIG_BOOTCOMMAND
Only needed when CONFIG_BOOTDELAY is enabled;
define a command string that is automatically executed
when no character is read on the console interface
within "Boot Delay" after reset.
CONFIG_BOOTARGS
This can be used to pass arguments to the bootm
command. The value of CONFIG_BOOTARGS goes into the
environment value "bootargs".
CONFIG_RAMBOOT and CONFIG_NFSBOOT
The value of these goes into the environment as
"ramboot" and "nfsboot" respectively, and can be used
as a convenience, when switching between booting from
RAM and NFS.
- Pre-Boot Commands:
CONFIG_PREBOOT
When this option is #defined, the existence of the
environment variable "preboot" will be checked
immediately before starting the CONFIG_BOOTDELAY
countdown and/or running the auto-boot command resp.
entering interactive mode.
This feature is especially useful when "preboot" is
automatically generated or modified. For an example
see the LWMON board specific code: here "preboot" is
modified when the user holds down a certain
combination of keys on the (special) keyboard when
booting the systems
- Serial Download Echo Mode:
CONFIG_LOADS_ECHO
If defined to 1, all characters received during a
serial download (using the "loads" command) are
echoed back. This might be needed by some terminal
emulations (like "cu"), but may as well just take
time on others. This setting #define's the initial
value of the "loads_echo" environment variable.
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
CONFIG_KGDB_BAUDRATE
Select one of the baudrates listed in
CONFIG_SYS_BAUDRATE_TABLE, see below.
- Monitor Functions:
Monitor commands can be included or excluded
from the build by using the #include files
"config_cmd_all.h" and #undef'ing unwanted
commands, or using "config_cmd_default.h"
and augmenting with additional #define's
for wanted commands.
The default command configuration includes all commands
except those marked below with a "*".
CONFIG_CMD_ASKENV * ask for env variable
CONFIG_CMD_BDI bdinfo
CONFIG_CMD_BEDBUG * Include BedBug Debugger
CONFIG_CMD_BMP * BMP support
CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
CONFIG_CMD_DTT * Digital Therm and Thermostat
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_MEMORY and CONFIG_MD5)
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CONFIG_CMD_MISC Misc functions like sleep etc
CONFIG_CMD_MMC * MMC memory mapped support
CONFIG_CMD_MII * MII utility commands
CONFIG_CMD_MTDPARTS * MTD partition support
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
CONFIG_CMD_PCI * pciinfo
CONFIG_CMD_PCMCIA * PCMCIA support
CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
host
CONFIG_CMD_PORTIO * Port I/O
CONFIG_CMD_REGINFO * Register dump
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SAVES * save S record dump
CONFIG_CMD_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
CONFIG_CMD_USB * USB support
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_FSL * Microblaze FSL support
EXAMPLE: If you want all functions except of network
support you can write:
#include "config_cmd_all.h"
#undef CONFIG_CMD_NET
Other Commands:
fdt (flattened device tree) command: CONFIG_OF_LIBFDT
Note: Don't enable the "icache" and "dcache" commands
(configuration option CONFIG_CMD_CACHE) unless you know
what you (and your U-Boot users) are doing. Data
cache cannot be enabled on systems like the 8xx or
8260 (where accesses to the IMMR region must be
uncached), and it cannot be disabled on all other
systems where we (mis-) use the data cache to hold an
initial stack and some data.
XXX - this list needs to get updated!
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
support for the SoC. There must be support in the SoC
specific code for a watchdog. For the 8xx and 8260
CPUs, the SIU Watchdog feature is enabled in the SYPCR
register. When supported for a specific SoC is
available, then no further board specific code should
be needed to use it.
CONFIG_HW_WATCHDOG
When using a watchdog circuitry external to the used
SoC, then define this variable and provide board
specific code for the "hw_watchdog_reset" function.
- U-Boot Version:
CONFIG_VERSION_VARIABLE
If this variable is defined, an environment variable
named "ver" is created by U-Boot showing the U-Boot
version as printed by the "version" command.
This variable is readonly.
- Real-Time Clock:
When CONFIG_CMD_DATE is selected, the type of the RTC
has to be selected, too. Define exactly one of the
following options:
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
CONFIG_RTC_MC13783 - use MC13783 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
CONFIG_SYS_RV3029_TCR - enable trickle charger on
RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
- GPIO Support:
CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
CONFIG_PCA953X_INFO - enable pca953x info command
The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
chip-ngpio pairs that tell the PCA953X driver the number of
pins supported by a particular chip.
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
(date and time) of an image is printed by image
commands like bootm or iminfo. This option is
automatically enabled when you select CONFIG_CMD_DATE .
- Partition Support:
CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
CONFIG_CMD_SCSI) you must configure support for at
least one partition type as well.
- IDE Reset method:
CONFIG_IDE_RESET_ROUTINE - this is defined in several
board configurations files but used nowhere!
CONFIG_IDE_RESET - is this is defined, IDE Reset will
be performed by calling the function
ide_set_reset(int reset)
which has to be defined in a board specific file
- ATAPI Support:
CONFIG_ATAPI
Set this to enable ATAPI support.
- LBA48 Support
CONFIG_LBA48
Set this to enable support for disks larger than 137GB
Also look at CONFIG_SYS_64BIT_LBA.
Whithout these , LBA48 support uses 32bit variables and will 'only'
support disks up to 2.1TB.
CONFIG_SYS_64BIT_LBA:
When enabled, makes the IDE subsystem use 64bit sector addresses.
Default is 32bit.
- SCSI Support:
At the moment only there is only support for the
SYM53C8XX SCSI controller; define
CONFIG_SCSI_SYM53C8XX to enable it.
CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
maximum numbers of LUNs, SCSI ID's and target
devices.
CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
- NETWORK Support (PCI):
CONFIG_E1000
Support for Intel 8254x gigabit chips.
CONFIG_E1000_FALLBACK_MAC
default MAC for empty EEPROM after production.
CONFIG_EEPRO100
Support for Intel 82557/82559/82559ER chips.
Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
write routine for first time initialisation.
CONFIG_TULIP
Support for Digital 2114x chips.
Optional CONFIG_TULIP_SELECT_MEDIA for board specific
modem chip initialisation (KS8761/QS6611).
CONFIG_NATSEMI
Support for National dp83815 chips.
CONFIG_NS8382X
Support for National dp8382[01] gigabit chips.
- NETWORK Support (other):
CONFIG_DRIVER_AT91EMAC
Support for AT91RM9200 EMAC.
CONFIG_RMII
Define this to use reduced MII inteface
CONFIG_DRIVER_AT91EMAC_QUIET
If this defined, the driver is quiet.
The driver doen't show link status messages.
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
CONFIG_LAN91C96_BASE
Define this to hold the physical address
of the LAN91C96's I/O space
CONFIG_LAN91C96_USE_32_BIT
Define this to enable 32 bit addressing
CONFIG_DRIVER_SMC91111
Support for SMSC's LAN91C111 chip
CONFIG_SMC91111_BASE
Define this to hold the physical address
of the device (I/O space)
CONFIG_SMC_USE_32_BIT
Define this if data bus is 32 bits
CONFIG_SMC_USE_IOFUNCS
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
CONFIG_FTGMAC100
Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
CONFIG_FTGMAC100_EGIGA
Define this to use GE link update with gigabit PHY.
Define this if FTGMAC100 is connected to gigabit PHY.
If your system has 10/100 PHY only, it might not occur
wrong behavior. Because PHY usually return timeout or
useless data when polling gigabit status and gigabit
control registers. This behavior won't affect the
correctnessof 10/100 link speed update.
CONFIG_SMC911X
Support for SMSC's LAN911x and LAN921x chips
CONFIG_SMC911X_BASE
Define this to hold the physical address
of the device (I/O space)
CONFIG_SMC911X_32_BIT
Define this if data bus is 32 bits
CONFIG_SMC911X_16_BIT
Define this if data bus is 16 bits. If your processor
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
CONFIG_SH_ETHER
Support for Renesas on-chip Ethernet controller
CONFIG_SH_ETHER_USE_PORT
Define the number of ports to be used
CONFIG_SH_ETHER_PHY_ADDR
Define the ETH PHY's address