printer-20240528_134035.cfg

[include mainsail.cfg]
[include sensorless.cfg]
[include ebb36.cfg]
# [include sb2209.cfg]
[include macros.cfg]
# [include nevermore.cfg]
[include disco_leds.cfg]
[include KAMP_Settings.cfg]
# [include stealthburner_leds_official.cfg]
[include config_backup.cfg]
[include bedfans.cfg]
[include K-ShakeTune/*.cfg]

# This file contains common pin mappings for the BIGTREETECH Manta M8P
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD12/PD13)".

[skew_correction] 


[autotune_tmc stepper_x]
motor: ldo-42sth48-2804ah
[autotune_tmc stepper_y]
motor: ldo-42sth48-2804ah
sgt: 1

[autotune_tmc stepper_z]
motor: ldo-42sth40-1684l300e
[autotune_tmc stepper_z1]
motor: ldo-42sth40-1684l300e
[autotune_tmc stepper_z2]
motor: ldo-42sth40-1684l300e


#[autotune_tmc extruder]
#motor: ldo-36sth20-1004ahg

[force_move]
enable_force_move: True

# See docs/Config_Reference.md for a description of parameters.
[mcu]
canbus_uuid: 20a9430e4fda

[exclude_object]
[pause_resume]

[firmware_retraction]
retract_length: 0.5
# The length of filament (in mm) to retract when G10 is activated,
# and to unretract when G11 is activated (but see
# unretract_extra_length below). The default is 0 mm.
retract_speed: 35
# The speed of retraction, in mm/s. The default is 20 mm/s.
# unretract_extra_length: -0.1
# The length (in mm) of *additional* filament to add when
# unretracting.
unretract_speed: 30
# The speed of unretraction, in mm/s. The default is 10 mm/s.

[gcode_arcs]
resolution: 0.1
#   An arc will be split into segments. Each segment's length will
#   equal the resolution in mm set above. Lower values will produce a
#   finer arc, but also more work for your machine. Arcs smaller than
#   the configured value will become straight lines. The default is
#   1mm.

[input_shaper]
#shaper_type_x: mzv
#shaper_freq_x: 64.6
#shaper_type_y: zv
#shaper_freq_y: 48.4


[printer]
kinematics: corexy
max_velocity: 300  
max_accel: 7100             #Max 4000
max_accel_to_decel: 7100
max_z_velocity: 15          #Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350
square_corner_velocity: 14.2  # 1/500 of max acceleration 

[temperature_sensor M8P]
sensor_type: temperature_mcu

[temperature_sensor CB1]
sensor_type: temperature_host

[temperature_sensor top_chamber]
sensor_type: Generic 3950
sensor_pin: PA1

[temperature_sensor ab_stepper]
sensor_type: Generic 3950
sensor_pin: PA3

[temperature_sensor bottom_chamber]
sensor_type: Generic 3950
sensor_pin: PA2

#####################################################################
# 	Beacon
#####################################################################

[beacon]
serial: /dev/serial/by-id/usb-Beacon_Beacon_RevH_E14A4A085154364134202020FF143631-if00
x_offset: 0 # update with offset from nozzle on your machine
y_offset: 24 # update with offset from nozzle on your machine
mesh_main_direction: x
mesh_runs: 2

[safe_z_home]
home_xy_position: 130, 125 # update for your machine
z_hop: 3

[resonance_tester]
accel_chip: beacon
probe_points: 130, 125, 20
accel_per_hz: 125
#####################################################################
# 	Probe
#####################################################################

# [probe]
# pin: EBBCan:PB5
# x_offset: 0				#<-!-!-!- Set to the position x of your probe relative to the nozzle
# y_offset: 0				#<-!-!-!- Set to the position y of your probe relative to the nozzle
# #z_offset: -1.430			#<-!-!-!- Set to the position z of your probe relative to the nozzle
# speed: 5
# lift_speed: 5
# samples: 5
# samples_result: median
# sample_retract_dist: 3
# samples_tolerance: 0.075
# samples_tolerance_retries: 10
# #					<-!-!-!- Uncomment below if you are using Boop
# activate_gcode:
#    #{% set PROBE_TEMP = printer.configfile.settings.extruder.min_extrude_temp %}
#    {% set PROBE_TEMP = 150 %}
#    {% set MAX_TEMP = PROBE_TEMP + 5 %}
#    {% set ACTUAL_TEMP = printer.extruder.temperature %}
#    {% set TARGET_TEMP = printer.extruder.target %}

#    {% if TARGET_TEMP > PROBE_TEMP %}
#        { action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
#        M109 S{ PROBE_TEMP }
#    {% else %}
#        # Temperature target is already low enough, but nozzle may still be too hot.
#        {% if ACTUAL_TEMP > MAX_TEMP %}
#            { action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
#            TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }
#        {% endif %}
#    {% endif %}

#####################################################################
#   X/Y Stepper Settings
#####################################################################

[stepper_x] #Connect the B Motor (gantry left) to MOTOR1
step_pin: PE2
dir_pin: !PB4
enable_pin: !PC11
microsteps: 64
rotation_distance: 40
endstop_pin: tmc5160_stepper_x:virtual_endstop
# full_steps_per_rotation: 200
position_min: 0
position_endstop: 255
position_max: 255
homing_speed: 125
homing_retract_dist: 0
homing_positive_dir: true

[tmc5160 stepper_x]
cs_pin: PC10
interpolate: False
run_current: 2.6
sense_resistor: 0.075
diag1_pin: ^!PF3
stealthchop_threshold: 1
driver_SGT: -1 #	<-!-!-!- Tune sensorless homing
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6

# [stepper_x] #Connect the B Motor (gantry left) to MOTOR1
# step_pin: PE2
# dir_pin: PB4
# enable_pin: !PC11
# microsteps: 64
# rotation_distance: 40
# endstop_pin: tmc2209_stepper_x:virtual_endstop
# position_min: 0 #-245
# position_endstop: 255 #10
# position_max: 255 #10
# homing_speed: 50
# homing_retract_dist: 0
# homing_positive_dir: true

# [tmc2209 stepper_x]
# uart_pin: PC10
# interpolate: False
# run_current: 1.06
# sense_resistor: 0.110
# diag_pin: ^PF3
# stealthchop_threshold: 1
# driver_SGTHRS: 98 #	<-!-!-!- Tune sensorless homing


#[tmc2130 stepper_y]
#cs_pin: PF13
#spi_bus: spi1
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999


[stepper_y] #Connect the A Motor (gantry right) to MOTOR2
step_pin: PF12
dir_pin: !PF11
enable_pin: !PB3
microsteps: 64
rotation_distance: 40
# full_steps_per_rotation: 200
endstop_pin: tmc5160_stepper_y:virtual_endstop
position_min: 0 #-250
position_endstop: 255 #10
position_max: 255 #10
homing_speed: 100
homing_retract_dist: 0
homing_positive_dir: true

[tmc5160 stepper_y]
cs_pin: PF13
interpolate: False
run_current: 2.4
sense_resistor: 0.075
diag1_pin: ^!PF4
stealthchop_threshold: 1
driver_SGT: -1 #	<-!-!-!- Tune sensorless homing
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6

# [stepper_y] #Connect the A Motor (gantry right) to MOTOR2
# step_pin: PF12
# dir_pin: PF11
# enable_pin: !PB3
# microsteps: 64
# rotation_distance: 40
# endstop_pin: tmc2209_stepper_y:virtual_endstop
# position_min: 0 #-250
# position_endstop: 260 #10
# position_max: 260 #10
# homing_speed: 50
# homing_retract_dist: 0
# homing_positive_dir: true

# [tmc2209 stepper_y]
# uart_pin: PF13
# interpolate: False
# run_current: 1.06
# sense_resistor: 0.110
# diag_pin: ^PF4
# stealthchop_threshold: 1
# driver_SGTHRS: 98 #	<-!-!-!- Tune sensorless homing


#####################################################################
#   Z Stepper Settings
#####################################################################

[stepper_z] #Connect the Z (Front Left) motor to MOTOR4
step_pin: PD3
dir_pin: !PD2
enable_pin: !PD5
rotation_distance: 4
microsteps: 64
endstop_pin: probe:z_virtual_endstop
position_max: 242
position_min: -10
homing_speed: 10
second_homing_speed: 3
homing_retract_dist: 0
full_steps_per_rotation:200

[tmc2209 stepper_z]
uart_pin: PD4
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[stepper_z1] #Connect the Z1 (Rear) motor to MOTOR5
step_pin: PC9
dir_pin: !PC8
enable_pin: !PD1
microsteps: 64
rotation_distance: 4
full_steps_per_rotation:200

[tmc2209 stepper_z1]
uart_pin: PD0
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[stepper_z2] #Connect the Z2 (Front Right) motor to MOTOR6
step_pin: PA10
dir_pin: !PA14
enable_pin: !PA15
microsteps: 64
rotation_distance: 4
full_steps_per_rotation:200

[tmc2209 stepper_z2]
uart_pin: PF8
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[filament_motion_sensor filament_runout_sensor]
detection_length: 14
#   The minimum length of filament pulled through the sensor to trigger
#   a state change on the switch_pin
#   Default is 7 mm.
extruder: extruder
#   The name of the extruder section this sensor is associated with.
#   This parameter must be provided.
switch_pin: PC5
# changing the switch_pin name according to your motherboard
pause_on_runout: False
runout_gcode:
  {action_respond_info("FILAMENT RUNOUT: Filament runout")}
  MR_NOTIFY TITLE="$printer_name" MESSAGE="Filement runout!"
  PAUSE
insert_gcode:
  {action_respond_info("FILAMENT RUNOUT: Filament inserted")}
#event_delay:
#pause_delay:

#[filament_switch_sensor material_0]
#switch_pin: PC1

# Motor6
#[extruder1]
#step_pin: PA10
#dir_pin: PA14
#enable_pin: !PA15
#heater_pin: PB5 # HE1
#sensor_pin: PA2 # T1
#...

#[filament_switch_sensor material_1]
#switch_pin: PC2

# Motor7
#[extruder2]
#step_pin: PD11
#dir_pin: PD9
#enable_pin: !PD15
#heater_pin: PB6 # HE2
#sensor_pin: PA3 # T2
#...

# Motor8
#[extruder3]
#step_pin: PD8
#dir_pin: PC6
#enable_pin: !PC7
#heater_pin: PE1 # HE3
#sensor_pin: PA4 # T3
#...

[heater_bed]
heater_pin: PB7
sensor_type: Generic 3950
sensor_pin: PA0 # TB
#control: pid
min_temp: 0
max_temp: 120
#pid_kp: 58.640
#pid_ki: 4.249
#pid_kd: 202.310

#####################################################################
#   FANS
#####################################################################

[multi_pin electronics_cooling]
pins: PE0, PC12

[controller_fan controller_fan]
pin: multi_pin:electronics_cooling
kick_start_time: 0.5
heater: heater_bed
# heater_temp: 45.0
idle_speed: 0
fan_speed: 0.5

[output_pin nevermore]
pin: PE6
value: 0
shutdown_value: 0

[temperature_fan cb1_fan]
pin: PE5
sensor_type: temperature_host
min_temp: -40
max_temp: 70
target_temp: 38
min_speed: 0.1
max_speed: 1.0
control: pid
off_below: 0.1
max_power: 1.0
pid_kp: 1.0
pid_ki: 0.5
pid_kd: 2.0


# [fan]
# pin: PE6

#[heater_fan fan1]
#pin: PE0

#[heater_fan fan2]
#pin: PC12

#[heater_fan fan3]
#pin: PE5

#[heater_fan fan4]
#pin: PE4

#[heater_fan fan5]
#pin: PB8
#tachometer_pin: PC14

#[heater_fan fan6]
#pin: PB9
#tachometer_pin: PC15

#[heater_fan SoC_fan]
#pin: CB1:gpio79
#pin: RPI:gpio26

########################################
# TMC2209 configuration
########################################

# [tmc2209 stepper_x]
# uart_pin: PC10
# diag_pin: ^PF3
# run_current: 0.800
# stealthchop_threshold: 0

# [tmc2209 stepper_y]
# uart_pin: PF13
# diag_pin: ^PF4
# run_current: 0.800
# stealthchop_threshold: 0

# [tmc2209 stepper_z]
# uart_pin: PF9
# diag_pin: ^PF5
# run_current: 0.650
# stealthchop_threshold: 0

#[tmc2209 stepper_]
#uart_pin: PD4
##diag_pin: PC0
#run_current: 0.650
#stealthchop_threshold: 999999

#[tmc2209 extruder]
#uart_pin: PD0
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder1]
#uart_pin: PF8
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder2]
#uart_pin: PD14
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder3]
#uart_pin: PD10
#run_current: 0.800
#stealthchop_threshold: 999999

########################################
# TMC2130 configuration
########################################

#[tmc2130 stepper_x]
#cs_pin: PC10
#spi_bus: spi1
##diag1_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 stepper_y]
#cs_pin: PF13
#spi_bus: spi1
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 stepper_z]
#cs_pin: PF9
#spi_bus: spi1
##diag1_pin: PF5
#run_current: 0.650
#stealthchop_threshold: 999999

#[tmc2130 stepper_]
#cs_pin: PD4
#spi_bus: spi1
##diag1_pin: PC0
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder]
#cs_pin: PD0
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder1]
#cs_pin: PF8
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder2]
#cs_pin: PD14
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder3]
#cs_pin: PD10
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#####################################################################
# 	Homing and Gantry Adjustment Routines
#####################################################################

[idle_timeout]
timeout: 1800

# [bed_mesh]
# speed: 200
# horizontal_move_z: 3
# mesh_min: 10,10
# mesh_max: 110,110
# probe_count: 3,3
# relative_reference_index: 4
# algorithm: lagrange

# [homing_override]
# axes: xyz
# gcode:
# 	{% set home_all = 'X' not in params and 'Y' not in params and 'Z' not in params %}

# #	{% if home_all or 'Y' in params %}
# 		#_HOME_Y
# #	{% endif %}

# 	{% if home_all or 'X' in params %}
# 		_HOME_X
# 	{% endif %}
	
# 	{% if home_all or 'Y' in params %}
# 		_HOME_Y
# 	{% endif %}
	
# 	{% if home_all or 'Z' in params %}
# 		G90
# 		G0 X125 Y125 F15000	# <-!-!-!- Set to the position of your Z endstop
# 		G28 Z
# 		G1 Z10
# 	{% endif %}
	
[z_tilt]
z_positions:
   -35, -24
   125, 266
   291, -24
points:
   30, 0
   125, 200
   230, 0
speed: 200
horizontal_move_z: 5
retries: 6
retry_tolerance: 0.005


[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PE9, EXP1_2=PE10,
    EXP1_3=PE11, EXP1_4=PE12,
    EXP1_5=PE13, EXP1_6=PE14,    # Slot in the socket on this side
    EXP1_7=PE15, EXP1_8=PB10,
    EXP1_9=<GND>, EXP1_10=<5V>,

    # EXP2 header
    EXP2_1=PB14, EXP2_2=PB13,
    EXP2_3=PF7, EXP2_4=PB12,
    EXP2_5=PE7, EXP2_6=PB11,      # Slot in the socket on this side
    EXP2_7=PE8, EXP2_8=<RST>,
    EXP2_9=<GND>, EXP2_10=<NC>


# See the sample-lcd.cfg file for definitions of common LCD displays.

#[bltouch]
#sensor_pin: PB2
#control_pin: PB1

# Proximity switch
#[probe]
#pin: PF6

#[output_pin ps_on_pin]
#pin: PC3

#[output_pin pc13_pin]
#pin: PC13

#[neopixel my_neopixel_1]
#pin: PA9

#[neopixel my_neopixel_2]
#pin: PB15

#[hall_filament_width_sensor]
#adc1: PC5
#adc2: PB0

#[adxl345]
#cs_pin: PC4
#spi_bus: spi1



# [gcode_macro PRINT_END]
# #   Use PRINT_END for the slicer ending script - please customise for your slicer of choice
# gcode:
#     # safe anti-stringing move coords
#     {% set th = printer.toolhead %}
#     {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %}
#     {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %}
#     {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %}
    
#     SAVE_GCODE_STATE NAME=STATE_PRINT_END
    
#     M400                           ; wait for buffer to clear
#     G92 E0                         ; zero the extruder
#     G1 E-2.0 F3600                 ; retract filament
    
#     TURN_OFF_HEATERS
    
#     G90                                      ; absolute positioning
#     G0 X{x_safe} Y{y_safe} Z{z_safe} F20000  ; move nozzle to remove stringing
#     G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600  ; park nozzle at rear
#     M107                                     ; turn off fan
    
#     BED_MESH_CLEAR
#     RESTORE_GCODE_STATE NAME=STATE_PRINT_END

[bed_mesh]
speed: 250
horizontal_move_z: 1
##--------------------------------------------------------------------
##	Uncomment below for 250mm build
mesh_min: 25, 24
mesh_max: 235,225

##	Uncomment for 300mm build
#mesh_min: 40, 40
#mesh_max: 260,260

##	Uncomment for 350mm build
#mesh_min: 40, 40
#mesh_max: 310,310
##--------------------------------------------------------------------
fade_start: 1
fade_end: 10.0
move_check_distance: 3
split_delta_z: 0.01
probe_count: 30, 30 # Values should be odd, so one point is directly at bed center
algorithm: bicubic
bicubic_tension: 0.2
# relative_reference_index: 12 # Update when changing probe_count, to ((x points * y points) - 1) / 2. (the center point)

[include moonraker_obico_macros.cfg]

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.079079, -0.063173, -0.057896, -0.050843, -0.043008, -0.029404, -0.036946, -0.017179, -0.028678, -0.012916, -0.020300, -0.005043, -0.017383, -0.000352, -0.011841, -0.002239, 0.000984, 0.003646, 0.005058, 0.001930, -0.000510, -0.004520, -0.002644, -0.020021, -0.013432, -0.034103, -0.027558, -0.050004, -0.043421, -0.069092
#*# 	  -0.054643, -0.060209, -0.046293, -0.047246, -0.032476, -0.030288, -0.023792, -0.017275, -0.012520, -0.010390, -0.013068, -0.005499, -0.006776, 0.004687, -0.001458, 0.009672, 0.006076, 0.016598, 0.008505, 0.016526, 0.003531, 0.007603, -0.001456, -0.007205, -0.011530, -0.018213, -0.026082, -0.033422, -0.041484, -0.056092
#*# 	  -0.056076, -0.056385, -0.044112, -0.043969, -0.032400, -0.027708, -0.021768, -0.015647, -0.010504, -0.007806, -0.004264, 0.001024, -0.004169, 0.005518, 0.001614, 0.011912, 0.007147, 0.018938, 0.011479, 0.017023, 0.006167, 0.004994, 0.000826, -0.006017, -0.010750, -0.017796, -0.024148, -0.032350, -0.035382, -0.050348
#*# 	  -0.058160, -0.054559, -0.048664, -0.040743, -0.033106, -0.025795, -0.022214, -0.014651, -0.013055, -0.002908, -0.006586, 0.002109, -0.001892, 0.006009, 0.004046, 0.013805, 0.014202, 0.020033, 0.016875, 0.015265, 0.011829, 0.008538, 0.003457, -0.005282, -0.005746, -0.017877, -0.019519, -0.031694, -0.032413, -0.049752
#*# 	  -0.055273, -0.052310, -0.044360, -0.038941, -0.028087, -0.024504, -0.014675, -0.013910, -0.006642, -0.005261, -0.000016, 0.001834, 0.004653, 0.005248, 0.008913, 0.014806, 0.014655, 0.021423, 0.014238, 0.018791, 0.010742, 0.013575, 0.004002, 0.001650, -0.007207, -0.013790, -0.022773, -0.026107, -0.033742, -0.041673
#*# 	  -0.059607, -0.051265, -0.047064, -0.036890, -0.032130, -0.022515, -0.016899, -0.009482, -0.008673, -0.001656, -0.000833, 0.004692, 0.004819, 0.006797, 0.007443, 0.009996, 0.014053, 0.015166, 0.018797, 0.013946, 0.014848, 0.006694, 0.008553, -0.001901, -0.001852, -0.015565, -0.015192, -0.029835, -0.030072, -0.039334
#*# 	  -0.060120, -0.054433, -0.048429, -0.041491, -0.033393, -0.030746, -0.018615, -0.014398, -0.006630, -0.007280, -0.001328, -0.003123, 0.004554, 0.004303, 0.006163, 0.005548, 0.009420, 0.014150, 0.016042, 0.015691, 0.011996, 0.008959, 0.001330, 0.001688, -0.006031, -0.012249, -0.022263, -0.027695, -0.035655, -0.039217
#*# 	  -0.060804, -0.053327, -0.049146, -0.040705, -0.036544, -0.026430, -0.020895, -0.013623, -0.008307, -0.004585, -0.002804, -0.000566, 0.003744, 0.004444, 0.008465, 0.007680, 0.013822, 0.014729, 0.021060, 0.014532, 0.015907, 0.008084, 0.007177, 0.001965, -0.000745, -0.010293, -0.016629, -0.024073, -0.034110, -0.040043
#*# 	  -0.059977, -0.050356, -0.049034, -0.040556, -0.033062, -0.027162, -0.022175, -0.015931, -0.006789, -0.005150, -0.000626, -0.001813, 0.005864, 0.006765, 0.011171, 0.009624, 0.018449, 0.015594, 0.019904, 0.017002, 0.018003, 0.014035, 0.009340, 0.003861, -0.000811, -0.005337, -0.014350, -0.020912, -0.030207, -0.036332
#*# 	  -0.059671, -0.052881, -0.048788, -0.041782, -0.034427, -0.028979, -0.023232, -0.018788, -0.012709, -0.008426, -0.003449, -0.002538, 0.004058, 0.006008, 0.009948, 0.012400, 0.018314, 0.020703, 0.023722, 0.020864, 0.018449, 0.016720, 0.012547, 0.005284, -0.001290, -0.006362, -0.016018, -0.015366, -0.027496, -0.031201
#*# 	  -0.063258, -0.050891, -0.051445, -0.039266, -0.038142, -0.027563, -0.029883, -0.022108, -0.018714, -0.011599, -0.007586, -0.004429, -0.002198, 0.001332, 0.010552, 0.011622, 0.019443, 0.013957, 0.025627, 0.012231, 0.019940, 0.011233, 0.013033, 0.001672, -0.000447, -0.007024, -0.014409, -0.019801, -0.025295, -0.033313
#*# 	  -0.067696, -0.061504, -0.053845, -0.050390, -0.040124, -0.037010, -0.031149, -0.027130, -0.020978, -0.017926, -0.011503, -0.011015, -0.002277, -0.000401, 0.003087, 0.007760, 0.011778, 0.015586, 0.017305, 0.017950, 0.012310, 0.014132, 0.004923, 0.004623, -0.006536, -0.006090, -0.021876, -0.018158, -0.031847, -0.029255
#*# 	  -0.067348, -0.061307, -0.054504, -0.047759, -0.044078, -0.036559, -0.031771, -0.024730, -0.024243, -0.015517, -0.015953, -0.008509, -0.007990, -0.001268, -0.001376, 0.006480, 0.009996, 0.013958, 0.021808, 0.014174, 0.015423, 0.005403, 0.007132, -0.003025, 0.000058, -0.018014, -0.010261, -0.024611, -0.023286, -0.037836
#*# 	  -0.071049, -0.065136, -0.056508, -0.053149, -0.043449, -0.040494, -0.032389, -0.029643, -0.021788, -0.020816, -0.019664, -0.015266, -0.009516, -0.000555, -0.012842, 0.010547, 0.001923, 0.018991, 0.012730, 0.020731, -0.005158, 0.017721, -0.000479, 0.008549, -0.000958, -0.000084, -0.020310, -0.020306, -0.022302, -0.028105
#*# 	  -0.071455, -0.066983, -0.059569, -0.052509, -0.046529, -0.040678, -0.036193, -0.027911, -0.024791, -0.017251, -0.020402, -0.007717, -0.007694, 0.003370, 0.002952, 0.012780, 0.010372, 0.016363, 0.018125, 0.020500, 0.017639, 0.015243, 0.011148, 0.004731, 0.001801, -0.003642, -0.007106, -0.017171, -0.019177, -0.028659
#*# 	  -0.074477, -0.063664, -0.065153, -0.060338, -0.053634, -0.046911, -0.043290, -0.038085, -0.034471, -0.026594, -0.023423, -0.013959, -0.013268, -0.003118, -0.006367, 0.005680, 0.004411, 0.014828, 0.013594, 0.017573, 0.013106, 0.012594, 0.006603, 0.001101, -0.005002, -0.016103, -0.013676, -0.022834, -0.019388, -0.033396
#*# 	  -0.061486, -0.070096, -0.066086, -0.064236, -0.053719, -0.049077, -0.044245, -0.040008, -0.031259, -0.025077, -0.020349, -0.014581, -0.008257, 0.000871, 0.000755, 0.010694, 0.008323, 0.019794, 0.014566, 0.019592, 0.015937, 0.018693, 0.008802, 0.004245, -0.000902, -0.004469, -0.009811, -0.014055, -0.019583, -0.023763
#*# 	  -0.060027, -0.054400, -0.056417, -0.058122, -0.055784, -0.046793, -0.042883, -0.034212, -0.029172, -0.021720, -0.019109, -0.011168, -0.003507, 0.001864, 0.006064, 0.010131, 0.014496, 0.019361, 0.023401, 0.021811, 0.019692, 0.018669, 0.017085, 0.008523, 0.005749, -0.001795, -0.002189, -0.011961, -0.009865, -0.021472
#*# 	  -0.043537, -0.053657, -0.057818, -0.064019, -0.053357, -0.052697, -0.041137, -0.040651, -0.027219, -0.028865, -0.021550, -0.015261, -0.005424, 0.000855, 0.005093, 0.008262, 0.013638, 0.022077, 0.019390, 0.025557, 0.017044, 0.020883, 0.010023, 0.010469, 0.003464, 0.000520, -0.007989, -0.010198, -0.015236, -0.016628
#*# 	  -0.055553, -0.057906, -0.046012, -0.063065, -0.059963, -0.053874, -0.047321, -0.040691, -0.034615, -0.027361, -0.023616, -0.016928, -0.009103, -0.001817, 0.001837, 0.006281, 0.010057, 0.013735, 0.018722, 0.019694, 0.018036, 0.014514, 0.011569, 0.007974, 0.005367, -0.001356, -0.003598, -0.010232, -0.014284, -0.018132
#*# 	  -0.051490, -0.050126, -0.056674, -0.061002, -0.058311, -0.053073, -0.045948, -0.041961, -0.032469, -0.027800, -0.019697, -0.017127, -0.006342, -0.003913, 0.005042, 0.007259, 0.012876, 0.014144, 0.020064, 0.022145, 0.021336, 0.022297, 0.014818, 0.010655, 0.006704, 0.001477, -0.003828, -0.007480, -0.013297, -0.015603
#*# 	  -0.048032, -0.053945, -0.041346, -0.060682, -0.055979, -0.050878, -0.046997, -0.040881, -0.032693, -0.030583, -0.024240, -0.019548, -0.009894, -0.003737, 0.000967, 0.005643, 0.011254, 0.015891, 0.021189, 0.023941, 0.023665, 0.021936, 0.016927, 0.012050, 0.008390, 0.005197, -0.001475, -0.003855, -0.008920, -0.013910
#*# 	  -0.062707, -0.053704, -0.067949, -0.065326, -0.068185, -0.061072, -0.055172, -0.049620, -0.043057, -0.037640, -0.029818, -0.024446, -0.016045, -0.013918, -0.008008, -0.003969, 0.006462, 0.009229, 0.016428, 0.016442, 0.016901, 0.014033, 0.011632, 0.006275, 0.000941, -0.003384, -0.007690, -0.011994, -0.016385, -0.018878
#*# 	  -0.078527, -0.073856, -0.073443, -0.074711, -0.079740, -0.074908, -0.070003, -0.062531, -0.057097, -0.050492, -0.044773, -0.037294, -0.031157, -0.027460, -0.022218, -0.017572, -0.010060, -0.003511, 0.003024, 0.005516, 0.005099, 0.003404, 0.000740, -0.003419, -0.007311, -0.012008, -0.018111, -0.020349, -0.024584, -0.026636
#*# 	  -0.089563, -0.078776, -0.090006, -0.078431, -0.086793, -0.081180, -0.076074, -0.068620, -0.062587, -0.056125, -0.049854, -0.043366, -0.036593, -0.031252, -0.027462, -0.022487, -0.014679, -0.009581, -0.002180, -0.001968, 0.000886, -0.003313, -0.004438, -0.008521, -0.010943, -0.016142, -0.019172, -0.024335, -0.027178, -0.028495
#*# 	  -0.090203, -0.077576, -0.089492, -0.078449, -0.083812, -0.078993, -0.073951, -0.067117, -0.061092, -0.053932, -0.049075, -0.042277, -0.035116, -0.030372, -0.025227, -0.021155, -0.012912, -0.009065, -0.002438, 0.001965, 0.001020, 0.000693, -0.001345, -0.004756, -0.006046, -0.010854, -0.014284, -0.016806, -0.019591, -0.020307
#*# 	  -0.089998, -0.087076, -0.084148, -0.081053, -0.085558, -0.078384, -0.072906, -0.065949, -0.060258, -0.053119, -0.046870, -0.040090, -0.035166, -0.030152, -0.024641, -0.018113, -0.014184, -0.007034, -0.002347, 0.001804, 0.003236, 0.003516, 0.001911, -0.001707, -0.003125, -0.007547, -0.008722, -0.012188, -0.014900, -0.016158
#*# 	  -0.095492, -0.085276, -0.092325, -0.087038, -0.086101, -0.079900, -0.074831, -0.066819, -0.061810, -0.054093, -0.048676, -0.042099, -0.035266, -0.031663, -0.024080, -0.019007, -0.013096, -0.006680, -0.000272, 0.002025, 0.003212, 0.004735, 0.003093, 0.000016, -0.000575, -0.005338, -0.007814, -0.008617, -0.010473, -0.012231
#*# 	  -0.100636, -0.100989, -0.096041, -0.097403, -0.093523, -0.086182, -0.079724, -0.072281, -0.067905, -0.061371, -0.055522, -0.048074, -0.041707, -0.036928, -0.031858, -0.025271, -0.018845, -0.010239, -0.006738, -0.003461, -0.002785, -0.001156, -0.002775, -0.005334, -0.007521, -0.010925, -0.012782, -0.014815, -0.016538, -0.017504
#*# 	  -0.135789, -0.132242, -0.131536, -0.130172, -0.125260, -0.119166, -0.112514, -0.106209, -0.100901, -0.095893, -0.089414, -0.085535, -0.077664, -0.072372, -0.067692, -0.061280, -0.054379, -0.048607, -0.043450, -0.042145, -0.042843, -0.042391, -0.044455, -0.045808, -0.047816, -0.052561, -0.056208, -0.057987, -0.061500, -0.064036
#*# x_count = 30
#*# y_count = 30
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 25.0
#*# max_x = 235.0
#*# min_y = 24.0
#*# max_y = 225.0
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 84.8
#*# shaper_type_y = ei
#*# shaper_freq_y = 76.6
#*#
#*# [probe]
#*# z_offset = -1.190
#*#
#*# [skew_correction calilantern_skew_profile]
#*# xy_skew = 0.0012680077976461247
#*# xz_skew = -0.004216297851837484
#*# yz_skew = -0.007303083885499536
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 58.218
#*# pid_ki = 4.043
#*# pid_kd = 209.585
#*#
#*# [beacon model default]
#*# model_coef = 1.6775179258007873,
#*# 	  1.9743239606559595,
#*# 	  0.6555520203745501,
#*# 	  0.27617472828151085,
#*# 	  0.29324410077497237,
#*# 	  0.21110935453098859,
#*# 	  -0.17333351624244564,
#*# 	  -0.15247257920885565,
#*# 	  0.1483399070952392,
#*# 	  0.09403870502055671
#*# model_domain = 1.8988377046543208e-07,1.9453473528181867e-07
#*# model_range = 0.200000,5.000000
#*# model_temp = 41.354547
#*# model_offset = 0.10000