printer-20240502_115026.cfg

[include mainsail.cfg]
[include sensorless.cfg]
[include ebb36.cfg]
# [include sb2209.cfg]
[include macros.cfg]
# [include nevermore.cfg]
[include disco_leds.cfg]
[include KAMP_Settings.cfg]
# [include stealthburner_leds_official.cfg]
[include config_backup.cfg]
[include bedfans.cfg]
#[include K-ShakeTune/*.cfg]

# This file contains common pin mappings for the BIGTREETECH Manta M8P
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD12/PD13)".

[skew_correction] 


[autotune_tmc stepper_x]
motor: ldo-42sth48-2804ah
[autotune_tmc stepper_y]
motor: ldo-42sth48-2804ah

[autotune_tmc stepper_z]
motor: ldo-42sth40-1684l300e
[autotune_tmc stepper_z1]
motor: ldo-42sth40-1684l300e
[autotune_tmc stepper_z2]
motor: ldo-42sth40-1684l300e


[autotune_tmc extruder]
motor: ldo-36sth20-1004ahg

[force_move]
enable_force_move: True

# See docs/Config_Reference.md for a description of parameters.
[mcu]
canbus_uuid: 20a9430e4fda

[exclude_object]
[pause_resume]

[firmware_retraction]
retract_length: 0.5
# The length of filament (in mm) to retract when G10 is activated,
# and to unretract when G11 is activated (but see
# unretract_extra_length below). The default is 0 mm.
retract_speed: 35
# The speed of retraction, in mm/s. The default is 20 mm/s.
# unretract_extra_length: -0.1
# The length (in mm) of *additional* filament to add when
# unretracting.
unretract_speed: 30
# The speed of unretraction, in mm/s. The default is 10 mm/s.

[gcode_arcs]
resolution: 0.1
#   An arc will be split into segments. Each segment's length will
#   equal the resolution in mm set above. Lower values will produce a
#   finer arc, but also more work for your machine. Arcs smaller than
#   the configured value will become straight lines. The default is
#   1mm.

[input_shaper]
#shaper_type_x: mzv
#shaper_freq_x: 64.6
#shaper_type_y: zv
#shaper_freq_y: 48.4


[printer]
kinematics: corexy
max_velocity: 300  
max_accel: 7100             #Max 4000
max_accel_to_decel: 7100
max_z_velocity: 15          #Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350
square_corner_velocity: 14.2  # 1/500 of max acceleration 

[temperature_sensor M8P]
sensor_type: temperature_mcu

[temperature_sensor CB1]
sensor_type: temperature_host

[temperature_sensor top_chamber]
sensor_type: Generic 3950
sensor_pin: PA1

[temperature_sensor ab_stepper]
sensor_type: Generic 3950
sensor_pin: PA3

[temperature_sensor bottom_chamber]
sensor_type: Generic 3950
sensor_pin: PA2

#####################################################################
# 	Beacon
#####################################################################

[beacon]
serial: /dev/serial/by-id/usb-Beacon_Beacon_RevH_E14A4A085154364134202020FF143631-if00
x_offset: 24 # update with offset from nozzle on your machine
y_offset: 0 # update with offset from nozzle on your machine
mesh_main_direction: x
mesh_runs: 2

[safe_z_home]
home_xy_position: 125, 125 # update for your machine
z_hop: 3

[resonance_tester]
accel_chip: beacon
probe_points: 125, 125, 20
#####################################################################
# 	Probe
#####################################################################

# [probe]
# pin: EBBCan:PB5
# x_offset: 0				#<-!-!-!- Set to the position x of your probe relative to the nozzle
# y_offset: 0				#<-!-!-!- Set to the position y of your probe relative to the nozzle
# #z_offset: -1.430			#<-!-!-!- Set to the position z of your probe relative to the nozzle
# speed: 5
# lift_speed: 5
# samples: 5
# samples_result: median
# sample_retract_dist: 3
# samples_tolerance: 0.075
# samples_tolerance_retries: 10
# #					<-!-!-!- Uncomment below if you are using Boop
# activate_gcode:
#    #{% set PROBE_TEMP = printer.configfile.settings.extruder.min_extrude_temp %}
#    {% set PROBE_TEMP = 150 %}
#    {% set MAX_TEMP = PROBE_TEMP + 5 %}
#    {% set ACTUAL_TEMP = printer.extruder.temperature %}
#    {% set TARGET_TEMP = printer.extruder.target %}

#    {% if TARGET_TEMP > PROBE_TEMP %}
#        { action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
#        M109 S{ PROBE_TEMP }
#    {% else %}
#        # Temperature target is already low enough, but nozzle may still be too hot.
#        {% if ACTUAL_TEMP > MAX_TEMP %}
#            { action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
#            TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }
#        {% endif %}
#    {% endif %}

#####################################################################
#   X/Y Stepper Settings
#####################################################################

[stepper_x] #Connect the B Motor (gantry left) to MOTOR1
step_pin: PE2
dir_pin: !PB4
enable_pin: !PC11
microsteps: 64
rotation_distance: 40
endstop_pin: tmc5160_stepper_x:virtual_endstop
# full_steps_per_rotation: 200
position_min: 0
position_endstop: 255
position_max: 255
homing_speed: 150
homing_retract_dist: 0
homing_positive_dir: true

[tmc5160 stepper_x]
cs_pin: PC10
interpolate: False
run_current: 2.8
sense_resistor: 0.075
diag1_pin: ^!PF3
stealthchop_threshold: 1
driver_SGT: -1 #	<-!-!-!- Tune sensorless homing
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6

# [stepper_x] #Connect the B Motor (gantry left) to MOTOR1
# step_pin: PE2
# dir_pin: PB4
# enable_pin: !PC11
# microsteps: 64
# rotation_distance: 40
# endstop_pin: tmc2209_stepper_x:virtual_endstop
# position_min: 0 #-245
# position_endstop: 255 #10
# position_max: 255 #10
# homing_speed: 50
# homing_retract_dist: 0
# homing_positive_dir: true

# [tmc2209 stepper_x]
# uart_pin: PC10
# interpolate: False
# run_current: 1.06
# sense_resistor: 0.110
# diag_pin: ^PF3
# stealthchop_threshold: 1
# driver_SGTHRS: 98 #	<-!-!-!- Tune sensorless homing


#[tmc2130 stepper_y]
#cs_pin: PF13
#spi_bus: spi1
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999


[stepper_y] #Connect the A Motor (gantry right) to MOTOR2
step_pin: PF12
dir_pin: !PF11
enable_pin: !PB3
microsteps: 64
rotation_distance: 40
# full_steps_per_rotation: 200
endstop_pin: tmc5160_stepper_y:virtual_endstop
position_min: 0 #-250
position_endstop: 260 #10
position_max: 260 #10
homing_speed: 150
homing_retract_dist: 0
homing_positive_dir: true

[tmc5160 stepper_y]
cs_pin: PF13
interpolate: False
run_current: 2.8
sense_resistor: 0.075
diag1_pin: ^!PF4
stealthchop_threshold: 1
driver_SGT: -1 #	<-!-!-!- Tune sensorless homing
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6

# [stepper_y] #Connect the A Motor (gantry right) to MOTOR2
# step_pin: PF12
# dir_pin: PF11
# enable_pin: !PB3
# microsteps: 64
# rotation_distance: 40
# endstop_pin: tmc2209_stepper_y:virtual_endstop
# position_min: 0 #-250
# position_endstop: 260 #10
# position_max: 260 #10
# homing_speed: 50
# homing_retract_dist: 0
# homing_positive_dir: true

# [tmc2209 stepper_y]
# uart_pin: PF13
# interpolate: False
# run_current: 1.06
# sense_resistor: 0.110
# diag_pin: ^PF4
# stealthchop_threshold: 1
# driver_SGTHRS: 98 #	<-!-!-!- Tune sensorless homing


#####################################################################
#   Z Stepper Settings
#####################################################################

[stepper_z] #Connect the Z (Front Left) motor to MOTOR4
step_pin: PD3
dir_pin: !PD2
enable_pin: !PD5
rotation_distance: 4
microsteps: 128
endstop_pin: probe:z_virtual_endstop
position_max: 242
position_min: -10
homing_speed: 10
second_homing_speed: 3
homing_retract_dist: 0
full_steps_per_rotation:200

[tmc2209 stepper_z]
uart_pin: PD4
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[stepper_z1] #Connect the Z1 (Rear) motor to MOTOR5
step_pin: PC9
dir_pin: !PC8
enable_pin: !PD1
microsteps: 128
rotation_distance: 4
full_steps_per_rotation:200

[tmc2209 stepper_z1]
uart_pin: PD0
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[stepper_z2] #Connect the Z2 (Front Right) motor to MOTOR6
step_pin: PA10
dir_pin: !PA14
enable_pin: !PA15
microsteps: 128
rotation_distance: 4
full_steps_per_rotation:200

[tmc2209 stepper_z2]
uart_pin: PF8
interpolate: False
run_current: 0.95
sense_resistor: 0.110
stealthchop_threshold: 999999

[filament_motion_sensor filament_runout_sensor]
detection_length: 14
#   The minimum length of filament pulled through the sensor to trigger
#   a state change on the switch_pin
#   Default is 7 mm.
extruder: extruder
#   The name of the extruder section this sensor is associated with.
#   This parameter must be provided.
switch_pin: PC5
# changing the switch_pin name according to your motherboard
pause_on_runout: False
runout_gcode:
  {action_respond_info("FILAMENT RUNOUT: Filament runout")}
  MR_NOTIFY TITLE="$printer_name" MESSAGE="Filement runout!"
  PAUSE
insert_gcode:
  {action_respond_info("FILAMENT RUNOUT: Filament inserted")}
#event_delay:
#pause_delay:

#[filament_switch_sensor material_0]
#switch_pin: PC1

# Motor6
#[extruder1]
#step_pin: PA10
#dir_pin: PA14
#enable_pin: !PA15
#heater_pin: PB5 # HE1
#sensor_pin: PA2 # T1
#...

#[filament_switch_sensor material_1]
#switch_pin: PC2

# Motor7
#[extruder2]
#step_pin: PD11
#dir_pin: PD9
#enable_pin: !PD15
#heater_pin: PB6 # HE2
#sensor_pin: PA3 # T2
#...

# Motor8
#[extruder3]
#step_pin: PD8
#dir_pin: PC6
#enable_pin: !PC7
#heater_pin: PE1 # HE3
#sensor_pin: PA4 # T3
#...

[heater_bed]
heater_pin: PB7
sensor_type: Generic 3950
sensor_pin: PA0 # TB
#control: pid
min_temp: 0
max_temp: 120
#pid_kp: 58.640
#pid_ki: 4.249
#pid_kd: 202.310

#####################################################################
#   FANS
#####################################################################

[multi_pin electronics_cooling]
pins: PE0, PC12

[controller_fan controller_fan]
pin: multi_pin:electronics_cooling
kick_start_time: 0.5
heater: heater_bed
# heater_temp: 45.0
idle_speed: 0
fan_speed: 0.5

[output_pin nevermore]
pin: PE6
value: 0
shutdown_value: 0

[temperature_fan cb1_fan]
pin: PE5
sensor_type: temperature_host
min_temp: -40
max_temp: 70
target_temp: 38
min_speed: 0.1
max_speed: 1.0
control: pid
off_below: 0.1
max_power: 1.0
pid_kp: 1.0
pid_ki: 0.5
pid_kd: 2.0


# [fan]
# pin: PE6

#[heater_fan fan1]
#pin: PE0

#[heater_fan fan2]
#pin: PC12

#[heater_fan fan3]
#pin: PE5

#[heater_fan fan4]
#pin: PE4

#[heater_fan fan5]
#pin: PB8
#tachometer_pin: PC14

#[heater_fan fan6]
#pin: PB9
#tachometer_pin: PC15

#[heater_fan SoC_fan]
#pin: CB1:gpio79
#pin: RPI:gpio26

########################################
# TMC2209 configuration
########################################

# [tmc2209 stepper_x]
# uart_pin: PC10
# diag_pin: ^PF3
# run_current: 0.800
# stealthchop_threshold: 0

# [tmc2209 stepper_y]
# uart_pin: PF13
# diag_pin: ^PF4
# run_current: 0.800
# stealthchop_threshold: 0

# [tmc2209 stepper_z]
# uart_pin: PF9
# diag_pin: ^PF5
# run_current: 0.650
# stealthchop_threshold: 0

#[tmc2209 stepper_]
#uart_pin: PD4
##diag_pin: PC0
#run_current: 0.650
#stealthchop_threshold: 999999

#[tmc2209 extruder]
#uart_pin: PD0
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder1]
#uart_pin: PF8
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder2]
#uart_pin: PD14
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2209 extruder3]
#uart_pin: PD10
#run_current: 0.800
#stealthchop_threshold: 999999

########################################
# TMC2130 configuration
########################################

#[tmc2130 stepper_x]
#cs_pin: PC10
#spi_bus: spi1
##diag1_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 stepper_y]
#cs_pin: PF13
#spi_bus: spi1
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 stepper_z]
#cs_pin: PF9
#spi_bus: spi1
##diag1_pin: PF5
#run_current: 0.650
#stealthchop_threshold: 999999

#[tmc2130 stepper_]
#cs_pin: PD4
#spi_bus: spi1
##diag1_pin: PC0
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder]
#cs_pin: PD0
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder1]
#cs_pin: PF8
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder2]
#cs_pin: PD14
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2130 extruder3]
#cs_pin: PD10
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999

#####################################################################
# 	Homing and Gantry Adjustment Routines
#####################################################################

[idle_timeout]
timeout: 1800

# [bed_mesh]
# speed: 200
# horizontal_move_z: 3
# mesh_min: 10,10
# mesh_max: 110,110
# probe_count: 3,3
# relative_reference_index: 4
# algorithm: lagrange

# [homing_override]
# axes: xyz
# gcode:
# 	{% set home_all = 'X' not in params and 'Y' not in params and 'Z' not in params %}

# #	{% if home_all or 'Y' in params %}
# 		#_HOME_Y
# #	{% endif %}

# 	{% if home_all or 'X' in params %}
# 		_HOME_X
# 	{% endif %}
	
# 	{% if home_all or 'Y' in params %}
# 		_HOME_Y
# 	{% endif %}
	
# 	{% if home_all or 'Z' in params %}
# 		G90
# 		G0 X125 Y125 F15000	# <-!-!-!- Set to the position of your Z endstop
# 		G28 Z
# 		G1 Z10
# 	{% endif %}
	
[z_tilt]
z_positions:
   -35, 0
   290, 125
   291, 0
points:
   30, 30
   125, 230
   230, 30
speed: 450
horizontal_move_z: 5
retries: 6
retry_tolerance: 0.0075


[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PE9, EXP1_2=PE10,
    EXP1_3=PE11, EXP1_4=PE12,
    EXP1_5=PE13, EXP1_6=PE14,    # Slot in the socket on this side
    EXP1_7=PE15, EXP1_8=PB10,
    EXP1_9=<GND>, EXP1_10=<5V>,

    # EXP2 header
    EXP2_1=PB14, EXP2_2=PB13,
    EXP2_3=PF7, EXP2_4=PB12,
    EXP2_5=PE7, EXP2_6=PB11,      # Slot in the socket on this side
    EXP2_7=PE8, EXP2_8=<RST>,
    EXP2_9=<GND>, EXP2_10=<NC>


# See the sample-lcd.cfg file for definitions of common LCD displays.

#[bltouch]
#sensor_pin: PB2
#control_pin: PB1

# Proximity switch
#[probe]
#pin: PF6

#[output_pin ps_on_pin]
#pin: PC3

#[output_pin pc13_pin]
#pin: PC13

#[neopixel my_neopixel_1]
#pin: PA9

#[neopixel my_neopixel_2]
#pin: PB15

#[hall_filament_width_sensor]
#adc1: PC5
#adc2: PB0

#[adxl345]
#cs_pin: PC4
#spi_bus: spi1



# [gcode_macro PRINT_END]
# #   Use PRINT_END for the slicer ending script - please customise for your slicer of choice
# gcode:
#     # safe anti-stringing move coords
#     {% set th = printer.toolhead %}
#     {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %}
#     {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %}
#     {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %}
    
#     SAVE_GCODE_STATE NAME=STATE_PRINT_END
    
#     M400                           ; wait for buffer to clear
#     G92 E0                         ; zero the extruder
#     G1 E-2.0 F3600                 ; retract filament
    
#     TURN_OFF_HEATERS
    
#     G90                                      ; absolute positioning
#     G0 X{x_safe} Y{y_safe} Z{z_safe} F20000  ; move nozzle to remove stringing
#     G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600  ; park nozzle at rear
#     M107                                     ; turn off fan
    
#     BED_MESH_CLEAR
#     RESTORE_GCODE_STATE NAME=STATE_PRINT_END

[bed_mesh]
speed: 450
horizontal_move_z: 5
##--------------------------------------------------------------------
##	Uncomment below for 250mm build
mesh_min: 40, 40
mesh_max: 210,210

##	Uncomment for 300mm build
#mesh_min: 40, 40
#mesh_max: 260,260

##	Uncomment for 350mm build
#mesh_min: 40, 40
#mesh_max: 310,310
##--------------------------------------------------------------------
fade_start: 0.6
fade_end: 10.0
probe_count: 5,5 # Values should be odd, so one point is directly at bed center
algorithm: bicubic
# relative_reference_index: 12 # Update when changing probe_count, to ((x points * y points) - 1) / 2. (the center point)

[include moonraker_obico_macros.cfg]
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.050625, -0.051563, -0.036094, -0.037266
#*# 	  -0.052031, -0.046406, -0.038750, -0.033125
#*# 	  -0.066875, -0.058438, -0.041172, -0.030547
#*# 	  -0.078828, -0.059453, -0.033672, -0.017656
#*# 	  -0.119609, -0.083594, -0.052031, -0.035547
#*# x_count = 4
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = lagrange
#*# tension = 0.2
#*# min_x = 63.16
#*# max_x = 186.28
#*# min_y = 40.65
#*# max_y = 208.29
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 66.2
#*# shaper_type_y = mzv
#*# shaper_freq_y = 47.8
#*#
#*# [probe]
#*# z_offset = -1.190
#*#
#*# [skew_correction calilantern_skew_profile]
#*# xy_skew = 0.0012680077976461247
#*# xz_skew = -0.004216297851837484
#*# yz_skew = -0.007303083885499536
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 58.218
#*# pid_ki = 4.043
#*# pid_kd = 209.585