JAILHOUSE

Introduction

Jailhouse is a partitioning Hypervisor based on Linux. It is able to run bare-metal applications or (adapted) operating systems besides Linux. For this purpose, it configures CPU and device virtualization features of the hardware platform in a way that none of these domains, called "cells" here, can interfere with each other in an unacceptable way.

Jailhouse is optimized for simplicity rather than feature richness. Unlike full-featured Linux-based hypervisors like KVM or Xen, Jailhouse does not support overcommitment of resources like CPUs, RAM or devices. It performs no scheduling and only virtualizes those resources in software, that are essential for a platform and cannot be partitioned in hardware.

Once Jailhouse is activated, it runs bare-metal, i.e. it takes full control over the hardware and needs no external support. However, in contrast to other bare-metal hypervisors, it is loaded and configured by a normal Linux system. Its management interface is based on Linux infrastructure. So you boot Linux first, then you enable Jailhouse and finally you split off parts of the system's resources and assign them to additional cells.

Community Resources

Project home:

• https://github.com/siemens/jailhouse

Source code:

• https://github.com/siemens/jailhouse.git
• [email protected]:siemens/jailhouse.git

Demo and testing images:

• https://github.com/siemens/jailhouse-images

Frequently Asked Questions (FAQ):

• See FAQ file

IRC channel:

• Freenode, irc.freenode.net, #jailhouse
• 

Mailing list:

• [email protected]

• Subscription:

  • [email protected]
  • https://groups.google.com/forum/#!forum/jailhouse-dev/join

• Archives

  • https://groups.google.com/forum/#!forum/jailhouse-dev
  • https://www.mail-archive.com/[email protected]

Continuous integration:

• https://github.com/siemens/jailhouse/actions

• Status:

  • on master
  • on next

Static code analysis:

• https://scan.coverity.com/projects/siemens-jailhouse

• Status:

  • on coverity_scan

See the contribution documentation for details on how to write Jailhouse patches and propose them for upstream integration.

Hardware requirements (preliminary)

x86 architecture:

• Intel system:

  • support for 64-bit and VMX, more precisely

    • EPT (extended page tables)
    • unrestricted guest mode
    • preemption timer

  • Intel IOMMU (VT-d) with interrupt remapping support (except when running inside QEMU)

• or AMD system:

  • support for 64-bit and SVM (AMD-V), and also

    • NPT (nested page tables); required
    • Decode Assists; recommended

  • AMD IOMMU (AMD-Vi) is unsupported now but will be required in future

• At least 2 logical CPUs

ARM architecture:

• ARMv7 with virtualization extensions or ARMv8

• At least 2 logical CPUs

• Supported ARM boards:

  • Banana Pi (see more)

  • Orange Pi Zero (256 MB version)

  • NVIDIA Jetson TK1

  • ARM Versatile Express with Cortex-A15 or A7 cores (includes ARM Fast Model)

  • emtrion emCON-RZ/G1x series based on Renesas RZ/G (see more)

• Supported ARM64 boards:

  • AMD Seattle / SoftIron Overdrive 3000

  • LeMaker HiKey

  • NVIDIA Jetson TX1 and TX2

  • Xilinx ZCU102 (ZynqMP evaluation board)

  • NXP MCIMX8M-EVK

Software requirements

x86 architecture:

• x86-64 Linux kernel (tested against 3.14+)

  • VT-d IOMMU usage (DMAR) has to be disabled in the Linux kernel, e.g. via the command line parameter:

    intel_iommu=off
    

  • To exploit the faster x2APIC, interrupt remapping needs to be on in the kernel (check for CONFIG_IRQ_REMAP)

• The hypervisor requires a contiguous piece of RAM for itself and each additional cell. This currently has to be pre-allocated during boot-up. On x86 this is typically done by adding

  memmap=82M$0x3a000000
  

  as parameter to the command line of the virtual machine's kernel. Note that if you plan to put this parameter in GRUB2 variables in /etc/default/grub, then you will need three escape characters before the dollar (e.g. GRUB_CMDLINE_LINUX_DEFAULT="memmap=82M\\\$0x3a000000").

ARM architecture:

• Linux kernel:

  • 3.19+ for ARM
  • 4.7+ for ARM64

• Appropriate boot loader support (typically U-Boot)

  • Linux is started in HYP mode
  • PSCI support for CPU offlining

• The hypervisor requires a contiguous piece of RAM for itself and each additional cell. This currently has to be pre-allocated during boot-up. On ARM this can be obtained by reducing the amount of memory seen by the kernel (through the mem= kernel boot parameter) or by modifying the Device Tree (i.e. the reserved-memory node).

Build & Installation

Simply run make, optionally specifying the target kernel directory:

make [KDIR=/path/to/kernel/objects]

Installation

It is recommended to install all of Jailhouse on your target machine. That will take care of a kernel module, the firmware, tools etc. Just call

make install

from the top-level directory.

The traditional Linux cross-compilation (i.e. ARCH= and CROSS_COMPILE=) and installation (i.e. DESTDIR=) flags are supported as well.

Running without Installation

Except for the hypervisor image jailhouse*.bin, that has to be available in the firmware search path, you can run Jailhouse from the build directory. If you cannot or do not want to use make install, you can either install just the firmware using make firmware_install or customize the firmware search path:

echo -n /path/to/jailhouse/hypervisor/ \
    > /sys/module/firmware_class/parameters/path

Configuration

Jailhouse requires one configuration file for the complete system and one for each additional cell besides the primary Linux. These .cell files have to be passed to the jailhouse command line tool for enabling the hypervisor or creating new cells.

On x86, the required hardware capabilities can be validated by running

jailhouse hardware check

A system configuration can be created on an x86 target system by running the following command:

jailhouse config create sysconfig.c

In order to translate this into the required binary form, place this file in the configs/x86/ directory. The build system will pick up every .c file from there and generate a corresponding .cell file.

Currently, there is no config generator for the ARM architecture; therefore the config file must be manually written by starting from the reference examples and checking hardware-specific datasheets, DTS and /proc entries.

Depending on the target system, the C structures may require some adjustments to make Jailhouse work properly or to reduce the desired access rights of the Linux root cell.

Configurations for additional (non-root) cells currently require manual creation. To study the structures, use one of the demo cell configurations files as reference, e.g. configs/x86/apic-demo.c or configs/x86/e1000-demo.c.

x86 Demonstration in QEMU/KVM

NOTE: You can also build and execute the following demo steps with the help of the jailhouse-images side project at https://github.com/siemens/jailhouse-images.

The included system configuration qemu-x86.c can be used to run Jailhouse in QEMU/KVM virtual machine on x86 hosts (Intel and AMD are supported). Currently it requires Linux 4.4 or newer on the host side. QEMU version 2.8 or newer is required.

You also need a Linux guest image with a recent kernel (tested with >= 3.9) and the ability to build a module for this kernel. Further steps depend on the type of CPU you have on your system.

For Intel CPUs: Make sure the kvm-intel module was loaded with nested=1 to enable nested VMX support. Start the virtual machine as follows:

qemu-system-x86_64 -machine q35,kernel_irqchip=split -m 1G -enable-kvm \
    -smp 4 -device intel-iommu,intremap=on,x-buggy-eim=on \
    -cpu host,-kvm-pv-eoi,-kvm-pv-ipi,-kvm-asyncpf,-kvm-steal-time,-kvmclock \
    -drive file=LinuxInstallation.img,format=raw|qcow2|...,id=disk,if=none \
    -device ide-hd,drive=disk -serial stdio -serial vc \
    -netdev user,id=net -device e1000e,addr=2.0,netdev=net \
    -device intel-hda,addr=1b.0 -device hda-duplex

For AMD CPUs: Make sure the kvm-amd module was loaded with nested=1 to enable nested SVM support. Start the virtual machine as follows:

qemu-system-x86_64 -machine q35 -m 1G -enable-kvm -smp 4 \
    -cpu host,-kvm-pv-eoi,-kvm-pv-ipi,-kvm-asyncpf,-kvm-steal-time,-kvmclock \
    -drive file=LinuxInstallation.img,format=raw|qcow2|...,id=disk,if=none \
    -device ide-hd,drive=disk -serial stdio -serial vc \
    -netdev user,id=net -device e1000e,addr=2.0,netdev=net \
    -device intel-hda,addr=1b.0 -device hda-duplex

Inside the VM, make sure that jailhouse-*.bin, generated by the build process, are available for firmware loading (typically /lib/firmware), see above for installation steps.

The Jailhouse QEMU cell config will block use of the serial port by the guest OS, so make sure that the guest kernel command line does NOT have its console set to log to the serial port (ie remove any 'console=ttyS0' arguments from the grub config). Reboot the guest and load jailhouse.ko. Then enable Jailhouse like this:

jailhouse enable /path/to/qemu-x86.cell

Next you can create a cell with a demonstration application as follows:

jailhouse cell create /path/to/apic-demo.cell
jailhouse cell load apic-demo /path/to/apic-demo.bin
jailhouse cell start apic-demo

apic-demo.bin is left by the built process in the inmates/demos/x86 directory. This application will program the APIC timer interrupt to fire at 10 Hz, measuring the jitter against the PM timer and displaying the result on the console. Given that this demonstration runs in a virtual machine, obviously no decent latencies should be expected.

After creation, cells are addressed via the command line tool by providing their names or their runtime-assigned IDs. You can obtain information about active cells this way:

jailhouse cell list

Cell destruction is performed by specifying the configuration file of the desired cell. This command will destroy the apic-demo:

jailhouse cell destroy apic-demo

Note that the first destruction or shutdown request on the apic-demo cell will fail. The reason is that this cell contains logic to demonstrate an ordered shutdown as well as the ability of a cell to reject shutdown requests.

The apic-demo cell has another special property for demonstration purposes: As long as it is running, no cell reconfigurations can be performed - the apic-demo locks the hypervisor in this regard. In order to destroy another cell or create an additional one, shut down the apic-demo first.

jailhouse cell shutdown apic-demo  # call again if error is returned

To demonstrate the execution of a second, non-Linux cell, issue the following commands:

jailhouse cell create /path/to/pci-demo.cell
jailhouse cell load pci-demo /path/to/pci-demo.bin \
    -s "con-base=0x2f8" -a 0x1000
jailhouse cell start pci-demo

The pci-demo will use the second serial port provided by QEMU. You will find its output in a virtual console of the QEMU window. The purpose of this demo is to show basic PCI device configuration and MSI handling.

While cell configurations are locked, it is still possible, though, to reload the content of existing cell (provided they accept their shutdown first). To reload and restart the tiny-demo, issue the following commands:

jailhouse cell start apic-demo
jailhouse cell load pci-demo /path/to/pci-demo.bin \
    -s "con-base=0x2f8" -a 0x1000
jailhouse cell start pci-demo

Finally, Jailhouse is can be stopped completely again:

jailhouse disable  # call again on error due to running apic-demo

All non-Linux cells running at that point will be destroyed, and resources will be returned to Linux.

ARM64 Demonstration in QEMU

Similarly like x86, Jailhouse can be tried out in a completely emulated ARM64 (aarch64) environment under QEMU. QEMU version 3.0 or later is required.

Start the QEMU machine like this:

qemu-system-aarch64 -cpu cortex-a57 -smp 16 -m 1G \
    -machine virt,gic-version=3,virtualization=on,its=off -nographic \
    -netdev user,id=net -device virtio-net-device,netdev=net \
    -drive file=LinuxInstallation.img,format=raw|qcow2|...,id=disk,if=none \
    -device virtio-blk-device,drive=disk \
    -kernel /path/to/kernel-image -append "root=/dev/vda1 mem=768M"

Jailhouse can be started after loading its kernel module. Run:

jailhouse enable /path/to/qemu-arm64.cell

The corresponding test to apic-demo on x86 is the gic-demo:

jailhouse cell create /path/to/qemu-arm64-inmate-demo.cell
jailhouse cell load inmate-demo /path/to/gic-demo.bin
jailhouse cell start inmate-demo