cmkbeat.full.yml

#================================ Configuration =====================================

cmkbeat:
  # How often to query livestatus for data. The default is 30s.
  period: 30s

  # The host and port where livestatus is listening.
  cmkHost: "localhost:6557"

  # Which livestatus table to query
  query: "services"

  # The columns of data you want to retrieve. At a minimum, the following fields must be included:
  # ["host_name", "display_name", "state",  "plugin_output", "perf_data"]
  columns: ["host_name", "display_name", "state", "plugin_output", "long_plugin_output", "percent_state_change", "perf_data"]
  
  # (Optional) An array of filters to apply to the query.
  # By default a query must pass all filters, but 'And: x' or 'Or: x' commands can be used,
  # where x specifies the number of previous filter lines to apply the operator to.
  # Ex. ["state = 1", "state = 3", "Or: 2" ] matches anything with a state of 1 OR 3.
  #filter: ["checks_enabled = 1", "host_state = 0"]

  # Whether or not to split up the perfdata into individual metrics. This will create additional fields such as
  # [cpu][value], [cpu][min], [cpu][max], etc. for each parameter in the performance data. Default is true.
  #metrics: true

  # If enabled, only perfdata for the specified services will be reported. Default is to include metrics for all services.
  #metrics_allow: ["CPU Utilization", "Disk IO", "Memory", "Interface"]
  
  # If enabled, perfdata for the specified services will not be reported. Default is to include metrics for all services.
  #metrics_block: ["Uptime", "System Time", "Check_MK", "Log"]
  
  # Whether to report just the 'value' field of the perfdata metrics, or whether to include the min / max / warn / crit
  # fields as well. Default is true.
  #metrics_value_only: true
  
#================================ General =====================================

# The name of the shipper that publishes the network data. It can be used to group
# all the transactions sent by a single shipper in the web interface.
# If this options is not defined, the hostname is used.
#name:

# The tags of the shipper are included in their own field with each
# transaction published. Tags make it easy to group servers by different
# logical properties.
#tags: ["service-X", "web-tier"]

# Optional fields that you can specify to add additional information to the
# output. Fields can be scalar values, arrays, dictionaries, or any nested
# combination of these.
#fields:
#  env: staging

# If this option is set to true, the custom fields are stored as top-level
# fields in the output document instead of being grouped under a fields
# sub-dictionary. Default is false.
#fields_under_root: false

# Internal queue size for single events in processing pipeline
#queue_size: 1000

# The internal queue size for bulk events in the processing pipeline.
# Do not modify this value.
#bulk_queue_size: 0

# Sets the maximum number of CPUs that can be executing simultaneously. The
# default is the number of logical CPUs available in the system.
#max_procs:

#================================ Processors =====================================

# Processors are used to reduce the number of fields in the exported event or to
# enhance the event with external meta data. This section defines a list of processors
# that are applied one by one and the first one receives the initial event:
#
#   event -> filter1 -> event1 -> filter2 ->event2 ...
#
# Supported processors: drop_fields, drop_event, include_fields
#
# For example, you can use the following processors to keep
# the fields that contain CPU load percentages, but remove the fields that
# contain CPU ticks values:
#
#processors:
#- include_fields:
#    fields: ["cpu"]
#- drop_fields:
#    fields: ["cpu.user", "cpu.system"]
#
# The following example drops the events that have the HTTP response code 200:
#
#processors:
#- drop_event:
#    when:
#       equals:
#           http.code: 200
#

#================================ Outputs =====================================

# Configure what outputs to use when sending the data collected by the beat.
# Multiple outputs may be used.

#-------------------------- Elasticsearch output ------------------------------
output.elasticsearch:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # Array of hosts to connect to.
  # Scheme and port can be left out and will be set to the default (http and 9200)
  # In case you specify and additional path, the scheme is required: http://localhost:9200/path
  # IPv6 addresses should always be defined as: https://[2001:db8::1]:9200
  hosts: ["localhost:9200"]

  # Set gzip compression level.
  #compression_level: 0

  # Optional protocol and basic auth credentials.
  #protocol: "https"
  #username: "elastic"
  #password: "changeme"

  # Dictionary of HTTP parameters to pass within the url with index operations.
  #parameters:
    #param1: value1
    #param2: value2

  # Number of workers per Elasticsearch host.
  #worker: 1

  # Optional index name. The default is "cmkbeat" plus date
  # and generates [cmkbeat-]YYYY.MM.DD keys.
  #index: "cmkbeat-%{+yyyy.MM.dd}"

  # Optional ingest node pipeline. By default no pipeline will be used.
  #pipeline: ""

  # Optional HTTP Path
  #path: "/elasticsearch"

  # Proxy server url
  #proxy_url: http://proxy:3128

  # The number of times a particular Elasticsearch index operation is attempted. If
  # the indexing operation doesn't succeed after this many retries, the events are
  # dropped. The default is 3.
  #max_retries: 3

  # The maximum number of events to bulk in a single Elasticsearch bulk API index request.
  # The default is 50.
  #bulk_max_size: 50

  # Configure http request timeout before failing an request to Elasticsearch.
  #timeout: 90

  # The number of seconds to wait for new events between two bulk API index requests.
  # If `bulk_max_size` is reached before this interval expires, addition bulk index
  # requests are made.
  #flush_interval: 1s

  # A template is used to set the mapping in Elasticsearch
  # By default template loading is enabled and the template is loaded.
  # These settings can be adjusted to load your own template or overwrite existing ones.

  # Set to false to disable template loading.
  #template.enabled: true

  # Template name. By default the template name is cmkbeat.
  #template.name: "cmkbeat"

  # Path to template file
  #template.path: "${path.config}/cmkbeat.template.json"

  # Overwrite existing template
  #template.overwrite: false

  # If set to true, cmkbeat checks the Elasticsearch version at connect time, and if it
  # is 2.x, it loads the file specified by the template.versions.2x.path setting. The
  # default is true.
  #template.versions.2x.enabled: true

  # Path to the Elasticsearch 2.x version of the template file.
  #template.versions.2x.path: "${path.config}/cmkbeat.template-es2x.json"

  # Use SSL settings for HTTPS. Default is true.
  #ssl.enabled: true

  # Configure SSL verification mode. If `none` is configured, all server hosts
  # and certificates will be accepted. In this mode, SSL based connections are
  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
  # `full`.
  #ssl.verification_mode: full

  # List of supported/valid TLS versions. By default all TLS versions 1.0 up to
  # 1.2 are enabled.
  #ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]

  # SSL configuration. By default is off.
  # List of root certificates for HTTPS server verifications
  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]

  # Certificate for SSL client authentication
  #ssl.certificate: "/etc/pki/client/cert.pem"

  # Client Certificate Key
  #ssl.key: "/etc/pki/client/cert.key"

  # Optional passphrase for decrypting the Certificate Key.
  #ssl.key_passphrase: ''

  # Configure cipher suites to be used for SSL connections
  #ssl.cipher_suites: []

  # Configure curve types for ECDHE based cipher suites
  #ssl.curve_types: []


#----------------------------- Logstash output --------------------------------
#output.logstash:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # The Logstash hosts
  #hosts: ["localhost:5044"]

  # Number of workers per Logstash host.
  #worker: 1

  # Set gzip compression level.
  #compression_level: 3

  # Optional load balance the events between the Logstash hosts
  #loadbalance: true

  # Number of batches to be send asynchronously to logstash while processing
  # new batches.
  #pipelining: 0

  # Optional index name. The default index name is set to name of the beat
  # in all lowercase.
  #index: 'cmkbeat'

  # SOCKS5 proxy server URL
  #proxy_url: socks5://user:password@socks5-server:2233

  # Resolve names locally when using a proxy server. Defaults to false.
  #proxy_use_local_resolver: false

  # Enable SSL support. SSL is automatically enabled, if any SSL setting is set.
  #ssl.enabled: true

  # Configure SSL verification mode. If `none` is configured, all server hosts
  # and certificates will be accepted. In this mode, SSL based connections are
  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
  # `full`.
  #ssl.verification_mode: full

  # List of supported/valid TLS versions. By default all TLS versions 1.0 up to
  # 1.2 are enabled.
  #ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]

  # Optional SSL configuration options. SSL is off by default.
  # List of root certificates for HTTPS server verifications
  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]

  # Certificate for SSL client authentication
  #ssl.certificate: "/etc/pki/client/cert.pem"

  # Client Certificate Key
  #ssl.key: "/etc/pki/client/cert.key"

  # Optional passphrase for decrypting the Certificate Key.
  #ssl.key_passphrase: ''

  # Configure cipher suites to be used for SSL connections
  #ssl.cipher_suites: []

  # Configure curve types for ECDHE based cipher suites
  #ssl.curve_types: []

#------------------------------- Kafka output ---------------------------------
#output.kafka:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # The list of Kafka broker addresses from where to fetch the cluster metadata.
  # The cluster metadata contain the actual Kafka brokers events are published
  # to.
  #hosts: ["localhost:9092"]

  # The Kafka topic used for produced events. The setting can be a format string
  # using any event field. To set the topic from document type use `%{[type]}`.
  #topic: beats

  # The Kafka event key setting. Use format string to create unique event key.
  # By default no event key will be generated.
  #key: ''

  # The Kafka event partitioning strategy. Default hashing strategy is `hash`
  # using the `output.kafka.key` setting or randomly distributes events if
  # `output.kafka.key` is not configured.
  #partition.hash:
    # If enabled, events will only be published to partitions with reachable
    # leaders. Default is false.
    #reachable_only: false

    # Configure alternative event field names used to compute the hash value.
    # If empty `output.kafka.key` setting will be used.
    # Default value is empty list.
    #hash: []

  # Authentication details. Password is required if username is set.
  #username: ''
  #password: ''

  # Kafka version cmkbeat is assumed to run against. Defaults to the oldest
  # supported stable version (currently version 0.8.2.0)
  #version: 0.8.2

  # Metadata update configuration. Metadata do contain leader information
  # deciding which broker to use when publishing.
  #metadata:
    # Max metadata request retry attempts when cluster is in middle of leader
    # election. Defaults to 3 retries.
    #retry.max: 3

    # Waiting time between retries during leader elections. Default is 250ms.
    #retry.backoff: 250ms

    # Refresh metadata interval. Defaults to every 10 minutes.
    #refresh_frequency: 10m

  # The number of concurrent load-balanced Kafka output workers.
  #worker: 1

  # The number of times to retry publishing an event after a publishing failure.
  # After the specified number of retries, the events are typically dropped.
  # Some Beats, such as Filebeat, ignore the max_retries setting and retry until
  # all events are published.  Set max_retries to a value less than 0 to retry
  # until all events are published. The default is 3.
  #max_retries: 3

  # The maximum number of events to bulk in a single Kafka request. The default
  # is 2048.
  #bulk_max_size: 2048

  # The number of seconds to wait for responses from the Kafka brokers before
  # timing out. The default is 30s.
  #timeout: 30s

  # The maximum duration a broker will wait for number of required ACKs. The
  # default is 10s.
  #broker_timeout: 10s

  # The number of messages buffered for each Kafka broker. The default is 256.
  #channel_buffer_size: 256

  # The keep-alive period for an active network connection. If 0s, keep-alives
  # are disabled. The default is 0 seconds.
  #keep_alive: 0

  # Sets the output compression codec. Must be one of none, snappy and gzip. The
  # default is gzip.
  #compression: gzip

  # The maximum permitted size of JSON-encoded messages. Bigger messages will be
  # dropped. The default value is 1000000 (bytes). This value should be equal to
  # or less than the broker's message.max.bytes.
  #max_message_bytes: 1000000

  # The ACK reliability level required from broker. 0=no response, 1=wait for
  # local commit, -1=wait for all replicas to commit. The default is 1.  Note:
  # If set to 0, no ACKs are returned by Kafka. Messages might be lost silently
  # on error.
  #required_acks: 1

  # The number of seconds to wait for new events between two producer API calls.
  #flush_interval: 1s

  # The configurable ClientID used for logging, debugging, and auditing
  # purposes.  The default is "beats".
  #client_id: beats

  # Enable SSL support. SSL is automatically enabled, if any SSL setting is set.
  #ssl.enabled: true

  # Optional SSL configuration options. SSL is off by default.
  # List of root certificates for HTTPS server verifications
  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]

  # Configure SSL verification mode. If `none` is configured, all server hosts
  # and certificates will be accepted. In this mode, SSL based connections are
  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
  # `full`.
  #ssl.verification_mode: full

  # List of supported/valid TLS versions. By default all TLS versions 1.0 up to
  # 1.2 are enabled.
  #ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]

  # Certificate for SSL client authentication
  #ssl.certificate: "/etc/pki/client/cert.pem"

  # Client Certificate Key
  #ssl.key: "/etc/pki/client/cert.key"

  # Optional passphrase for decrypting the Certificate Key.
  #ssl.key_passphrase: ''

  # Configure cipher suites to be used for SSL connections
  #ssl.cipher_suites: []

  # Configure curve types for ECDHE based cipher suites
  #ssl.curve_types: []

#------------------------------- Redis output ---------------------------------
#output.redis:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # The list of Redis servers to connect to. If load balancing is enabled, the
  # events are distributed to the servers in the list. If one server becomes
  # unreachable, the events are distributed to the reachable servers only.
  #hosts: ["localhost:6379"]

  # The Redis port to use if hosts does not contain a port number. The default
  # is 6379.
  #port: 6379

  # The name of the Redis list or channel the events are published to. The
  # default is cmkbeat.
  #key: cmkbeat

  # The password to authenticate with. The default is no authentication.
  #password:

  # The Redis database number where the events are published. The default is 0.
  #db: 0

  # The Redis data type to use for publishing events. If the data type is list,
  # the Redis RPUSH command is used. If the data type is channel, the Redis
  # PUBLISH command is used. The default value is list.
  #datetype: list

  # The number of workers to use for each host configured to publish events to
  # Redis. Use this setting along with the loadbalance option. For example, if
  # you have 2 hosts and 3 workers, in total 6 workers are started (3 for each
  # host).
  #worker: 1

  # If set to true and multiple hosts or workers are configured, the output
  # plugin load balances published events onto all Redis hosts. If set to false,
  # the output plugin sends all events to only one host (determined at random)
  # and will switch to another host if the currently selected one becomes
  # unreachable. The default value is true.
  #loadbalance: true

  # The Redis connection timeout in seconds. The default is 5 seconds.
  #timeout: 5s

  # The number of times to retry publishing an event after a publishing failure.
  # After the specified number of retries, the events are typically dropped.
  # Some Beats, such as Filebeat, ignore the max_retries setting and retry until
  # all events are published. Set max_retries to a value less than 0 to retry
  # until all events are published. The default is 3.
  #max_retries: 3

  # The maximum number of events to bulk in a single Redis request or pipeline.
  # The default is 2048.
  #bulk_max_size: 2048

  # The URL of the SOCKS5 proxy to use when connecting to the Redis servers. The
  # value must be a URL with a scheme of socks5://.
  #proxy_url:

  # This option determines whether Redis hostnames are resolved locally when
  # using a proxy. The default value is false, which means that name resolution
  # occurs on the proxy server.
  #proxy_use_local_resolver: false

  # Enable SSL support. SSL is automatically enabled, if any SSL setting is set.
  #ssl.enabled: true

  # Configure SSL verification mode. If `none` is configured, all server hosts
  # and certificates will be accepted. In this mode, SSL based connections are
  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
  # `full`.
  #ssl.verification_mode: full

  # List of supported/valid TLS versions. By default all TLS versions 1.0 up to
  # 1.2 are enabled.
  #ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]

  # Optional SSL configuration options. SSL is off by default.
  # List of root certificates for HTTPS server verifications
  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]

  # Certificate for SSL client authentication
  #ssl.certificate: "/etc/pki/client/cert.pem"

  # Client Certificate Key
  #ssl.key: "/etc/pki/client/cert.key"

  # Optional passphrase for decrypting the Certificate Key.
  #ssl.key_passphrase: ''

  # Configure cipher suites to be used for SSL connections
  #ssl.cipher_suites: []

  # Configure curve types for ECDHE based cipher suites
  #ssl.curve_types: []


#------------------------------- File output ----------------------------------
#output.file:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # Path to the directory where to save the generated files. The option is
  # mandatory.
  #path: "/tmp/cmkbeat"

  # Name of the generated files. The default is `cmkbeat` and it generates
  # files: `cmkbeat`, `cmkbeat.1`, `cmkbeat.2`, etc.
  #filename: cmkbeat

  # Maximum size in kilobytes of each file. When this size is reached, and on
  # every cmkbeat restart, the files are rotated. The default value is 10240
  # kB.
  #rotate_every_kb: 10000

  # Maximum number of files under path. When this number of files is reached,
  # the oldest file is deleted and the rest are shifted from last to first. The
  # default is 7 files.
  #number_of_files: 7


#----------------------------- Console output ---------------------------------
#output.console:
  # Boolean flag to enable or disable the output module.
  #enabled: true

  # Pretty print json event
  #pretty: false

#================================= Paths ======================================

# The home path for the cmkbeat installation. This is the default base path
# for all other path settings and for miscellaneous files that come with the
# distribution (for example, the sample dashboards).
# If not set by a CLI flag or in the configuration file, the default for the
# home path is the location of the binary.
#path.home:

# The configuration path for the cmkbeat installation. This is the default
# base path for configuration files, including the main YAML configuration file
# and the Elasticsearch template file. If not set by a CLI flag or in the
# configuration file, the default for the configuration path is the home path.
#path.config: ${path.home}

# The data path for the cmkbeat installation. This is the default base path
# for all the files in which cmkbeat needs to store its data. If not set by a
# CLI flag or in the configuration file, the default for the data path is a data
# subdirectory inside the home path.
#path.data: ${path.home}/data

# The logs path for a cmkbeat installation. This is the default location for
# the Beat's log files. If not set by a CLI flag or in the configuration file,
# the default for the logs path is a logs subdirectory inside the home path.
#path.logs: ${path.home}/logs

#================================ Logging =====================================
# There are three options for the log output: syslog, file, stderr.
# Under Windows systems, the log files are per default sent to the file output,
# under all other system per default to syslog.

# Sets log level. The default log level is info.
# Available log levels are: critical, error, warning, info, debug
#logging.level: info

# Enable debug output for selected components. To enable all selectors use ["*"]
# Other available selectors are "beat", "publish", "service"
# Multiple selectors can be chained.
#logging.selectors: [ ]

# Send all logging output to syslog. The default is false.
#logging.to_syslog: true

# If enabled, cmkbeat periodically logs its internal metrics that have changed
# in the last period. For each metric that changed, the delta from the value at
# the beginning of the period is logged. Also, the total values for
# all non-zero internal metrics are logged on shutdown. The default is true.
#logging.metrics.enabled: true

# The period after which to log the internal metrics. The default is 30s.
#logging.metrics.period: 30s

# Logging to rotating files files. Set logging.to_files to false to disable logging to
# files.
logging.to_files: true
logging.files:
  # Configure the path where the logs are written. The default is the logs directory
  # under the home path (the binary location).
  #path: /var/log/cmkbeat

  # The name of the files where the logs are written to.
  #name: cmkbeat

  # Configure log file size limit. If limit is reached, log file will be
  # automatically rotated
  #rotateeverybytes: 10485760 # = 10MB

  # Number of rotated log files to keep. Oldest files will be deleted first.
  #keepfiles: 7