nRF52_MultipleRandomServos.ino

/****************************************************************************************************************************
  NRF52_MultipleRandomServos.ino
  For :
  - nRF52832-based boards such as AdaFruit Feather nRF52832,
  - nRF52840-based boards such as Adafruit nRF52840 Express, Itsy-Bitsy nRF52840 Express, NINA_B302_ublox, etc.

  Written by Khoi Hoang

  Built by Khoi Hoang https://github.com/khoih-prog/NRF52_ISR_Servo
  Licensed under MIT license
*****************************************************************************************************************************/

/****************************************************************************************************************************
   From ESP32 Servo Example Using Arduino ESP32 Servo Library
   John K. Bennett
   March, 2017

   Different servos require different pulse widths to vary servo angle, but the range is
   an approximately 500-2500 microsecond pulse every 20ms (50Hz). In general, hobbyist servos
   sweep 180 degrees, so the lowest number in the published range for a particular servo
   represents an angle of 0 degrees, the middle of the range represents 90 degrees, and the top
   of the range represents 180 degrees. So for example, if the range is 1000us to 2000us,
   1000us would equal an angle of 0, 1500us would equal 90 degrees, and 2000us would equal 1800
   degrees.

   - Circuit:
   Servo motors have three wires: power, ground, and signal. The power wire is typically red,
   the ground wire is typically black or brown, and the signal wire is typically yellow,
   orange or white. Since the NRF52 can supply limited current at only 3.3V, and servos draw
   considerable power, we will connect servo power to the VBat pin of the NRF52 (located
   near the USB connector). THIS IS ONLY APPROPRIATE FOR SMALL SERVOS.

   We could also connect servo power to a separate external power source (as long as we connect all of
   the grounds (NRF52, servo, and external power).
   In this example, we just connect NRF52 ground to servo ground. The servo signal pins
   connect to any available GPIO pins on the NRF52 (in this example, we use pins (D1-D6).

   In this example, we assume four Tower Pro SG90 small servos.
   The published min and max for this servo are 500 and 2400, respectively.
   These values actually drive the servos a little past 0 and 180, so
   if you are particular, adjust the min and max values to match your needs.
   Experimentally, 800 and 2450 are pretty close to 0 and 180.
*****************************************************************************************************************************/

#define TIMER_INTERRUPT_DEBUG       4
#define ISR_SERVO_DEBUG             4

#include "NRF52_ISR_Servo.h"

// Published values for SG90 servos; adjust if needed
#define MIN_MICROS        800
#define MAX_MICROS        2450

#define SERVO_PIN_1       A0
#define SERVO_PIN_2       A1
#define SERVO_PIN_3       A2
#define SERVO_PIN_4       A3
#define SERVO_PIN_5       A4
#define SERVO_PIN_6       A5

typedef struct
{
  int     servoIndex;
  uint8_t servoPin;
} ISR_servo_t;

#define NUM_SERVOS            6

ISR_servo_t ISR_servo[] =
{
  { -1, SERVO_PIN_1 }, { -1, SERVO_PIN_2 }, { -1, SERVO_PIN_3 }, { -1, SERVO_PIN_4 }, { -1, SERVO_PIN_5 }, { -1, SERVO_PIN_6 }
};


void setup()
{
  Serial.begin(115200);

  while (!Serial && millis() < 5000);

  delay(200);

  Serial.print(F("\nStarting NRF52_MultipleRandomServos on "));
  Serial.println(BOARD_NAME);
  Serial.println(NRF52_ISR_SERVO_VERSION);

  for (int index = 0; index < NUM_SERVOS; index++)
  {
    ISR_servo[index].servoIndex = NRF52_ISR_Servos.setupServo(ISR_servo[index].servoPin, MIN_MICROS, MAX_MICROS);

    if (ISR_servo[index].servoIndex != -1)
    {
      Serial.print(F("Setup OK Servo index = "));
      Serial.println(ISR_servo[index].servoIndex);
      NRF52_ISR_Servos.setPosition(ISR_servo[index].servoIndex, 0);
    }
    else
    {
      Serial.print(F("Setup Failed Servo index = "));
      Serial.println(ISR_servo[index].servoIndex);
    }
  }
}

void printServoInfo(int indexServo)
{
  Serial.print(F("Servos idx = "));
  Serial.print(indexServo);
  Serial.print(F(", act. pos. (deg) = "));
  Serial.print(NRF52_ISR_Servos.getPosition(ISR_servo[indexServo].servoIndex) );
  Serial.print(F(", pulseWidth (us) = "));
  Serial.println(NRF52_ISR_Servos.getPulseWidth(ISR_servo[indexServo].servoIndex));
}

void loop()
{
  int position;      // position in degrees

  position = 0;
  Serial.println(F("Servos @ 0 degree"));

  for (int index = 0; index < NUM_SERVOS; index++)
  {
    NRF52_ISR_Servos.setPosition(ISR_servo[index].servoIndex, position );
    printServoInfo(index);
  }

  // waits 5s between test
  delay(5000);

  position = 90;
  Serial.println(F("Servos @ 90 degree"));

  for (int index = 0; index < NUM_SERVOS; index++)
  {
    NRF52_ISR_Servos.setPosition(ISR_servo[index].servoIndex, position );
    printServoInfo(index);
  }

  // waits 5s between test
  delay(5000);

  position = 180;
  Serial.println(F("Servos @ 180 degree"));

  for (int index = 0; index < NUM_SERVOS; index++)
  {
    NRF52_ISR_Servos.setPosition(ISR_servo[index].servoIndex, position );
    printServoInfo(index);
  }

  // waits 5s between test
  delay(5000);

  Serial.println(F("Servos sweeps from 0-180 degree"));

  for (position = 0; position <= 180; position += 5)
  {
    // goes from 0 degrees to 180 degrees
    // in steps of 1 degree
    for (int index = 0; index < NUM_SERVOS; index++)
    {
      NRF52_ISR_Servos.setPosition(ISR_servo[index].servoIndex, position );
    }

    // waits 0.1s for the servo to reach the position
    delay(100);
  }

  // waits 5s between test
  delay(5000);
}