OV2640 Camera Works for Setup but Boot Fails with erorr 4 #1766

jtricerolph · 2023-01-04T20:35:05Z

jtricerolph
Jan 4, 2023

Use a ESP32CAM from supplier listed on comments as good, camera only marked OV2640, shows reference image but on reboot in normal get camera error 4? Any suggestions?

jtricerolph · 2023-01-04T23:26:40Z

jtricerolph
Jan 4, 2023
Author

so after rebooting again and waiting some time eventually gets going but recognition shows -1 for all digits

1 reply

haverland Jan 8, 2023
Collaborator

Your alignment mars are to small (the red dots).
Set it up. And if it not helps try other models.
For ROI-Configuration see https://jomjol.github.io/AI-on-the-edge-device-docs/ROI-Configuration/ (section dig-class100 / dig-cont )

jtricerolph · 2023-01-05T06:49:36Z

github-actions[bot]
bot Jan 5, 2023

Please provide a logfile!
Make sure to first enable the DEBUG level in Settings->Configuration->Debug->Logfile Log Level!
Then wait until the issue arises again.
When you copy the log into here, please make sure to use Fenced code blocks by wrapping it into separate lines with ```, see https://docs.github.com/en/get-started/writing-on-github/working-with-advanced-formatting/creating-and-highlighting-code-blocks#fenced-code-blocks

1 reply

jtricerolph Jan 5, 2023
Author

I will sort that.
This morning woke to find the esp32cam unresponsive so rebooted, since then got a few clicks on the meter but while at work can see a misread caused error with negative usage and not have any more updated in last few hours, will check again when home.

As commented by others the responsiveness kf ui seems very poor like esp is being over burdened.

Is there anyway to sin the recognition is say a docker on server and just pull from a remote camera or even cctv rstp or something as have many old cctv cameras that could be repourposed

jtricerolph · 2023-01-05T21:51:34Z

jtricerolph
Jan 5, 2023
Author

So this seems to be a continuing issue.
Camera works fine on setup.
On restart from webgui either initial setup or reconfiguration on first restart I get error 4 for camera issue.
However if I restart again from the error page that prevents loading of webgui the 2nd time system loads and processes reading.
Logs below.
Any sugestions;

0d02h00m55s] 2023-01-05T21:43:43 <WRN> [OTA] Reboot in 5sec
[0d00h00m04s] 2023-01-05T21:43:57 <INF> [MAIN] =================================================
[0d00h00m04s] 2023-01-05T21:43:57 <INF> [MAIN] ==================== Startup ====================
[0d00h00m04s] 2023-01-05T21:43:57 <INF> [MAIN] =================================================
[0d00h00m04s] 2023-01-05T21:43:57 <INF> [MAIN] Branch: 'HEAD', Revision: 04f2f23+, Date/Time: 2022-12-19 20:41, Web UI: Release: v13.0.8 (Commit: 04f2f23+)
[0d00h00m04s] 2023-01-05T21:43:57 <INF> [MAIN] Reset reason: Via esp_restart
[0d00h00m09s] 2023-01-05T21:44:02 <INF> [MAIN] =================================================
[0d00h00m09s] 2023-01-05T21:44:02 <INF> [MAIN] ================== Main Started =================
[0d00h00m09s] 2023-01-05T21:44:02 <INF> [MAIN] =================================================
[0d00h00m09s] 2023-01-05T21:44:02 <INF> [MAIN] The device has 8 MBytes of PSRAM
[0d00h00m09s] 2023-01-05T21:44:02 <WRN> [MAIN] Failed to initialize camera module, retrying...
[0d00h00m13s] 2023-01-05T21:44:06 <ERR> [MAIN] Failed to initialize camera module!
[0d00h00m13s] 2023-01-05T21:44:06 <ERR> [MAIN] Check that your camera module is working and connected properly!
[0d00h00m13s] 2023-01-05T21:44:06 <ERR> [HELPER] New System Status: 0x00000004
[0d00h00m15s] 2023-01-05T21:44:08 <ERR> [MAIN] Initialization failed. Not starting flows!
[0d00h00m16s] 2023-01-05T21:44:09 <ERR> [MAIN SERVER] We have a critical error, not serving main page!
[0d00h02m44s] 2023-01-05T21:46:37 <INF> [OTA] Reboot triggered by Software (5s).
[0d00h02m44s] 2023-01-05T21:46:37 <WRN> [OTA] Reboot in 5sec
[0d00h00m04s] 2023-01-05T21:46:59 <INF> [MAIN] =================================================
[0d00h00m04s] 2023-01-05T21:46:59 <INF> [MAIN] ==================== Startup ====================
[0d00h00m04s] 2023-01-05T21:46:59 <INF> [MAIN] =================================================
[0d00h00m04s] 2023-01-05T21:46:59 <INF> [MAIN] Branch: 'HEAD', Revision: 04f2f23+, Date/Time: 2022-12-19 20:41, Web UI: Release: v13.0.8 (Commit: 04f2f23+)
[0d00h00m04s] 2023-01-05T21:46:59 <INF> [MAIN] Reset reason: Via esp_restart
[0d00h00m09s] 2023-01-05T21:47:04 <INF> [MAIN] =================================================
[0d00h00m09s] 2023-01-05T21:47:04 <INF> [MAIN] ================== Main Started =================
[0d00h00m09s] 2023-01-05T21:47:04 <INF> [MAIN] =================================================
[0d00h00m09s] 2023-01-05T21:47:04 <INF> [MAIN] The device has 8 MBytes of PSRAM
[0d00h00m11s] 2023-01-05T21:47:06 <INF> [MAIN] Initialization completed successfully!
[0d00h00m15s] 2023-01-05T21:47:10 <INF> [SNTP] Time zone set to GMT
[0d00h00m15s] 2023-01-05T21:47:10 <DBG> [MQTT] Digitizer interval is 5.0 minutes => setting MQTT LWT timeout to 12.5 minutes.
[0d00h00m15s] 2023-01-05T21:47:10 <DBG> [MQTT IF] URI: mqtt://10.88.1.109:1883, clientname: House, user: homeassistant, password: XXXXXXXX, maintopic: Electric, last-will-topic: Electric/connection, keepAlive: 750, RetainFlag: 1
[0d00h00m15s] 2023-01-05T21:47:10 <INF> [MQTT IF] Init
[0d00h00m15s] 2023-01-05T21:47:10 <INF> [MQTT IF] Client started, waiting for established connection...
[0d00h00m15s] 2023-01-05T21:47:10 <DBG> [TFLITE SERVER] ----------------------------------------------------------------
[0d00h00m15s] 2023-01-05T21:47:10 <INF> [TFLITE SERVER] Round #1 started
[0d00h00m16s] 2023-01-05T21:47:11 <DBG> [MAIN SERVER] info_get_handler
[0d00h00m16s] 2023-01-05T21:47:11 <DBG> [MAIN SERVER] info_get_handler
[0d00h00m16s] 2023-01-05T21:47:11 <DBG> [MAIN SERVER] info_get_handler
[0d00h00m25s] 2023-01-05T21:47:20 <INF> [MQTT SERVER] MQTT - Sending Homeassistant Discovery Topics (Meter Type: energy, Value Unit: kWh , Rate Unit: kW)...
[0d00h00m25s] 2023-01-05T21:47:20 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/uptime/config, content: { "~": "Electric", "unique_id": "Electric-uptime", "object_id": "Electric_uptime.. (msg_id=2)
[0d00h00m25s] 2023-01-05T21:47:20 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/MAC/config, content: { "~": "Electric", "unique_id": "Electric-MAC", "object_id": "Electric_MAC", "na.. (msg_id=3)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/hostname/config, content: { "~": "Electric", "unique_id": "Electric-hostname", "object_id": "Electric_host.. (msg_id=4)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/freeMem/config, content: { "~": "Electric", "unique_id": "Electric-freeMem", "object_id": "Electric_freeM.. (msg_id=5)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/wifiRSSI/config, content: { "~": "Electric", "unique_id": "Electric-wifiRSSI", "object_id": "Electric_wifi.. (msg_id=6)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/CPUtemp/config, content: { "~": "Electric", "unique_id": "Electric-CPUtemp", "object_id": "Electric_CPUte.. (msg_id=7)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/interval/config, content: { "~": "Electric", "unique_id": "Electric-interval", "object_id": "Electric_inte.. (msg_id=8)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/IP/config, content: { "~": "Electric", "unique_id": "Electric-IP", "object_id": "Electric_IP", "name.. (msg_id=9)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/status/config, content: { "~": "Electric", "unique_id": "Electric-status", "object_id": "Electric_status.. (msg_id=10)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: homeassistant/sensor/Electric/rate_per_digitalization_round/config, content: { "~": "Electric", "unique_id": "Electric-rate_per_digitalization_round", "objec.. (msg_id=15)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT SERVER] Publishing static MQTT topics...
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/MAC, content: CC:DB:A7:16:74:68 (msg_id=19)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/IP, content: 10.88.0.177 (msg_id=20)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/hostname, content: electricmeter (msg_id=21)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/interval, content: 5.0 (msg_id=22)
[0d00h00m25s] 2023-01-05T21:47:21 <DBG> [MQTT SERVER] Publishing system MQTT topics...
[0d00h00m26s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/uptime, content: 17 (msg_id=23)
[0d00h00m26s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/freeMem, content: 3090443 (msg_id=24)
[0d00h00m26s] 2023-01-05T21:47:21 <DBG> [MQTT IF] Published topic: Electric/status, content: Take Image (msg_id=27)
[0d00h00m31s] 2023-01-05T21:47:26 <DBG> [MQTT IF] Published topic: Electric/status, content: Aligning (msg_id=28)
[0d00h01m22s] 2023-01-05T21:48:18 <DBG> [MAIN SERVER] info_get_handler
[0d00h01m23s] 2023-01-05T21:48:19 <DBG> [MAIN SERVER] info_get_handler
[0d00h01m31s] 2023-01-05T21:48:27 <DBG> [MQTT IF] Published topic: Electric/status, content: Digitalization of ROIs (msg_id=29)
[0d00h01m32s] 2023-01-05T21:48:27 <DBG> [CNN] doFlow nach Alignment
[0d00h01m33s] 2023-01-05T21:48:28 <DBG> [OTA FILE] log_get_last_part_handler
[0d00h01m35s] 2023-01-05T21:48:30 <DBG> [TFLITE] Make Allocate
[0d00h01m35s] 2023-01-05T21:48:30 <DBG> [CNN] Processing Number 'main'
[0d00h01m35s] 2023-01-05T21:48:30 <DBG> [CNN] ROI #0 - TfLite
[0d00h01m35s] 2023-01-05T21:48:30 <DBG> [CNN] CNN Type: DoubleHyprid10
[0d00h01m40s] 2023-01-05T21:48:36 <DBG> [CNN] Nach Invoke
[0d00h01m41s] 2023-01-05T21:48:36 <DBG> [CNN] _num (p, m): 1 2 0 _val (p, m): 0.992935 0.006937 0.000078 result: 1.006938 _fit: 0.999872
[0d00h01m41s] 2023-01-05T21:48:36 <DBG> [CNN] ROI #1 - TfLite
[0d00h01m41s] 2023-01-05T21:48:36 <DBG> [CNN] CNN Type: DoubleHyprid10
[0d00h01m46s] 2023-01-05T21:48:42 <DBG> [CNN] Nach Invoke
[0d00h01m46s] 2023-01-05T21:48:42 <DBG> [CNN] _num (p, m): 6 7 5 _val (p, m): 0.995372 0.001670 0.002803 result: 5.997191 _fit: 0.998175
[0d00h01m46s] 2023-01-05T21:48:42 <DBG> [CNN] ROI #2 - TfLite
[0d00h01m46s] 2023-01-05T21:48:42 <DBG> [CNN] CNN Type: DoubleHyprid10
[0d00h01m52s] 2023-01-05T21:48:48 <DBG> [CNN] Nach Invoke
[0d00h01m52s] 2023-01-05T21:48:48 <DBG> [CNN] _num (p, m): 2 3 1 _val (p, m): 0.996919 0.003081 0.000000 result: 2.003081 _fit: 1.000000
[0d00h01m52s] 2023-01-05T21:48:48 <DBG> [CNN] ROI #3 - TfLite
[0d00h01m52s] 2023-01-05T21:48:48 <DBG> [CNN] CNN Type: DoubleHyprid10
[0d00h01m58s] 2023-01-05T21:48:54 <DBG> [CNN] Nach Invoke
[0d00h01m58s] 2023-01-05T21:48:54 <DBG> [CNN] _num (p, m): 4 5 3 _val (p, m): 0.984990 0.014998 0.000011 result: 4.014998 _fit: 0.999988
[0d00h01m58s] 2023-01-05T21:48:54 <DBG> [CNN] ROI #4 - TfLite
[0d00h01m58s] 2023-01-05T21:48:54 <DBG> [CNN] CNN Type: DoubleHyprid10
[0d00h02m00s] 2023-01-05T21:48:56 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m02s] 2023-01-05T21:48:57 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m08s] 2023-01-05T21:49:04 <DBG> [CNN] Nach Invoke
[0d00h02m08s] 2023-01-05T21:49:04 <DBG> [CNN] _num (p, m): 5 6 4 _val (p, m): 0.999964 0.000035 0.000001 result: 5.000035 _fit: 0.999999
[0d00h02m08s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/status, content: Post-Processing (msg_id=30)
[0d00h02m08s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout _analog=0, _extendedResolution=0, prev=-1
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] ZeigerEvalHybridNeu - kein Vorgänger - Ergebnis = 5 zahl: 5.000035 zahl_vorgaenger = -1.000000 eval_vorgaenger = -1 DigitalUnschaerfe = 0.200000
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout(dig100) prev=5
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] ZeigerEvalHybridNeu - KEIN Analoger Vorgänger, kein Ziffernwechsel, da Vorkomma weit genug weg = 4 zahl: 4.014998 zahl_vorgaenger = 5.000035 eval_vorgaenger = 5 DigitalUnschaerfe = 0.200000
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#ZeigerEvalHybridNeu()= 4
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#result= 45
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] ZeigerEvalHybridNeu - KEIN Analoger Vorgänger, kein Ziffernwechsel, da Vorkomma weit genug weg = 2 zahl: 2.003081 zahl_vorgaenger = 4.014998 eval_vorgaenger = 4 DigitalUnschaerfe = 0.200000
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#ZeigerEvalHybridNeu()= 2
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#result= 245
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] ZeigerEvalHybridNeu - KEIN Analoger Vorgänger, kein Ziffernwechsel, da Vorkomma weit genug weg = 6 zahl: 5.997191 zahl_vorgaenger = 2.003081 eval_vorgaenger = 2 DigitalUnschaerfe = 0.200000
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#ZeigerEvalHybridNeu()= 6
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#result= 6245
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] ZeigerEvalHybridNeu - KEIN Analoger Vorgänger, kein Ziffernwechsel, da Vorkomma weit genug weg = 1 zahl: 1.006938 zahl_vorgaenger = 5.997191 eval_vorgaenger = 6 DigitalUnschaerfe = 0.200000
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#ZeigerEvalHybridNeu()= 1
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [CNN] getReadout#result= 16245
[0d00h02m09s] 2023-01-05T21:49:04 <INF> [POSTPROC] main: Raw: 16245, Value: 16245, Status: no error
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/status, content: Sending MQTT (msg_id=31)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT SERVER] Publishing system MQTT topics...
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/uptime, content: 120 (msg_id=32)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/freeMem, content: 3109015 (msg_id=33)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/wifiRSSI, content: -66 (msg_id=34)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/CPUtemp, content: 55 (msg_id=35)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT] Publishing MQTT topics...
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/main/value, content: 16245 (msg_id=36)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/main/error, content: no error (msg_id=37)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/main/rate, content: 0.008381 (msg_id=38)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/main/rate_per_time_unit, content: 0.502864 (msg_id=39)
[0d00h02m09s] 2023-01-05T21:49:04 <DBG> [MQTT IF] Published topic: Electric/main/changeabsolut, content: 1 (msg_id=40)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [MQTT IF] Published topic: Electric/main/rate_per_digitalization_round, content: 1 (msg_id=41)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [MQTT IF] Published topic: Electric/main/raw, content: 16245 (msg_id=42)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [MQTT IF] Published topic: Electric/main/timestamp, content: 2023-01-05T21:47:26+0000 (msg_id=43)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [MQTT IF] Published topic: Electric/main/json, content: { "value": "16245", "raw": "16245", "pre": "16245", "error": ".. (msg_id=44)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [MQTT IF] Published topic: Electric/status, content: Flow finished (msg_id=45)
[0d00h02m09s] 2023-01-05T21:49:05 <DBG> [TFLITE SERVER] CPU Temperature: 55.6
[0d00h02m09s] 2023-01-05T21:49:05 <INF> [TFLITE SERVER] Round #1 completed
[0d00h02m11s] 2023-01-05T21:49:07 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m11s] 2023-01-05T21:49:07 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m12s] 2023-01-05T21:49:07 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m25s] 2023-01-05T21:49:21 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m25s] 2023-01-05T21:49:21 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m25s] 2023-01-05T21:49:21 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m27s] 2023-01-05T21:49:23 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m27s] 2023-01-05T21:49:23 <DBG> [MAIN SERVER] info_get_handler
[0d00h02m32s] 2023-01-05T21:49:28 <DBG> [OTA FILE] log_get_last_part_handler

4 replies

caco3 Jan 6, 2023
Collaborator

https://github.com/jomjol/AI-on-the-edge-device/wiki/Error-Codes#0x00000004-cam-bad

jtricerolph Jan 6, 2023
Author

Thanks for the link but already been there, error page links to code list also.
This is why I included comments about how camera works fine on startup initial config, and in pretty sure after a power cycle, seem to only get this issue after reboot from normal webui, rebooting from the error page after reboot from normal ui then starts up corectly and up to round 152 so far since last reboot/power cycle.
This to me suggests that camera isn't incompatable, damaged or broken given this is reliably reproducible.

caco3 Jan 8, 2023
Collaborator

Without such a problematic device in my hands its difficult to trace it down.

I still thinks that there is something odd with your hardware as many other do not have this issue but use the same software!

jtricerolph Jan 8, 2023
Author

2 days without issue, I mean if it is only after save and reboot and seccond reboot resolves then can live with it.
Just wanted to report it.
The fact it works OK after 2nd reboot or power cycle made me think it was soft issue rather than hard as would imagine hardware issue to be persistent.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

OV2640 Camera Works for Setup but Boot Fails with erorr 4 #1766

{{title}}

Replies: 3 comments 6 replies

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

Select a reply

OV2640 Camera Works for Setup but Boot Fails with erorr 4 #1766

jtricerolph Jan 4, 2023

Replies: 3 comments · 6 replies

jtricerolph Jan 4, 2023 Author

haverland Jan 8, 2023 Collaborator

github-actions[bot] bot Jan 5, 2023

jtricerolph Jan 5, 2023 Author

jtricerolph Jan 5, 2023 Author

caco3 Jan 6, 2023 Collaborator

jtricerolph Jan 6, 2023 Author

caco3 Jan 8, 2023 Collaborator

jtricerolph Jan 8, 2023 Author

jtricerolph
Jan 4, 2023

Replies: 3 comments 6 replies

jtricerolph
Jan 4, 2023
Author

haverland Jan 8, 2023
Collaborator

github-actions[bot]
bot Jan 5, 2023

jtricerolph Jan 5, 2023
Author

jtricerolph
Jan 5, 2023
Author

caco3 Jan 6, 2023
Collaborator

jtricerolph Jan 6, 2023
Author

caco3 Jan 8, 2023
Collaborator

jtricerolph Jan 8, 2023
Author