Board: Phytec phyWAVE KW22

Manufacturer

Designed and produced by PHYTEC Messtechnik GmbH, D-55129 Mainz.

Components

MCU MKW22D512	CM4, 32-bit, 64kB RAM
Light	(CLS15-22C/L213x/TR8)
Pressure	(MPL3115A2)
Tri-axis accelerometer	(MMA8652FC)
Tri-axis magnetometer	(MAG3110FCR1)
IR-Termopile Sensor	(TMP006)
Humidity Sensor	(HDC1000)
RGB-LED
Capacitive Button
1x User-Button
Integrated IEEE802.15.4(2006)-compliant radio at 2.4 GHz, 250kBit/s	Support for dual PAN ID mode

Layout / Hardware

phyWAVE-A-Eval-Board with equipped phyWAVE-KW22 processor/radio-module.

Details

The PCB-pieces with the mounted sensors can be separated from the eval-board to capture sensor-values from specific spatial points.

Implementation Status

Device	ID	Supported	Comments
MCU	MKW22D512	yes	mainline
Low-level driver	GPIO	yes	PR
	PWM	yes	PR
	UART	yes	PR
	I2C	yes	PR
	SPI	yes	PR
	USB	no
	RTT	yes	PR
	RNG	yes	PR
	Timer	yes	PR
Radio Chip	integrated	partly, waiting for ng_netdev	PR
Humidity Sensor	HDC1000	yes	mainline
Pressure Sensor	MPL3115A2	yes	mainline
Accelerometer	MMA8652FC	yes	mainline
Magnetometer	MAG3110FCR1	yes	mainline
Light Sensor	CLS15-22C/L213x/TR8	yes	WIP
IR-Termopile Sensor	TMP006	yes	mainline
Capacitive Button	PCB	no	planned

Toolchains

See ARM Family

Working:

• arm-none-eabi-gcc

Debugging

In order to program (flash) and debug the node you need OpenOCD and an ARM version of gdb (arm-none-eabi-gdb), which provided by most toolchains. Most Linux distributions provide also a package for OpenOCD. The required configuration files are provided by RIOT. Since version 0.9 of OpenOCD the target microcontroller MKW22D512 is supported. The following section describes how to install OpenOCD and set up a gdb-debugging session.

Setup the Environment

The debugging setting consists of openocd and GDB. Additionally one can use CGDB frontend for GDB or Nemiver (sudo yum install nemiver) for a more fancy looking.

• Various libraries:
  Command for installing them in Ubuntu 14.04:
  sudo apt-get install gcc libudev-dev libusb-1.0-0-dev libfox-1.6-dev autotools-dev autoconf automake libtool gdb-arm-none-eabi gcc-arm-none-eabi cgdb libhidapi-hidraw0 libusb-dev libhidapi-dev libhidapi-hidraw0-dbg
  Command for installing them in Fedora 21 /CentOS 7:
  sudo yum install libudev-devel libusb-devel fox autoconf automake libtool cgdb hidapi-devel libftdi-devel systemd-devel arm-none-eabi-gdb arm-none-eabi-gcc arm-none-eabi-newlib
  ATTENTION: Caused by a BUG in Fedora 21 arm-none-eabi-gcc the provided Toolchain from the Repository isn't able to build RIOT-OS (and a lot more of THUMB-Code Projects) properly! Better use Linaro Toolchain or Toolchain from https://launchpad.net/gcc-arm-embedded. You have to export the Path into your $PATH or e.g. edit your ~/.bashrc file.
  For building openOCD it is possible that you need also (Fedora 21 / CentOS 7):
  sudo yum install mpfr-devel flex gmp-devel libmpc-devel texinfo bison ncurses-libs ncurses-devel expat expat-devel make gcc gcc-c++
  

Install openocd with the following steps (it is possible that you must use 'sudo', depending on your rights for the installed Development-Tools):

clone git://git.code.sf.net/p/openocd/code
./bootstrap
./configure --enable-cmsis-dap
make
sudo make install

Add hidraw permissions:

• Open /etc/udev/rules.d/99-hidraw-permissions.rules and append:

`KERNEL=="hidraw*", SUBSYSTEM=="hidraw", MODE="0664", GROUP="plugdev"
ls -l /dev/hidraw*`

Debug Steps

• Build RIOT for the phyWAVE (pba-d-01) board
  Navigate to the appropriate application inside the RIOT folder structure you want to build. Build, debug or flash with:

BOARD=pba-d-01-kw2x make
BOARD=pba-d-01-kw2x make flash
BOARD=pba-d-01-kw2x make debug
BOARD=pba-d-01-kw2x make reset
BOARD=pba-d-01-kw2x make term (to start the terminal connection to the board)

It is possible if you are using Fedora that your OpenOCD cannot connect to your Board, if so, try:

sudo groupadd plugdev
sudo usermod -aG plugdev YOURUSERNAME
sudo usermod -aG dialout YOURUSERNAME
sudo reboot

Important hints

Missleading openocd terminal print

When perform "BOARD=pba-d-01 make flash" and the target is getting flashed, openocd prints the following message:

flash configuration field erased, please reset the device

Do not reset the device, the terminal print is missleading!!!
If one is disconnecting the target, or shutting down openocd during flash the target will be locked!!

Check for fitting .elf file

To prevent the risk of device locking, there is a automatic test that validates if the .elf-file was built with a fitting board-configuration. This automatic test is executed when perform "make debug" or "make flash".
The successful test is indicated before flash or debug with the following print:

Flash configuration tested... [OK]

If the test fails, the flash or debug process will abort.

Reflash the target in case of an empty or wrong image

If the target-flash is empty or there is a wrong config loaded to the flash, openocd won't work in the described way above. One can fix this following:

• push and hold reset and start openocd in the RIOT-application build-directory.

openocd -f ../../boards/pba-d-01/dist/mkw22d512.cfg
telnet localhost 4444
reset halt

• release reset

flash write_image erase examples/hello-world/bin/pba-d-01/hello-world.elf