Skip to content

Documentation ARexxAPI MAILWRITE

Jens Maus edited this page Feb 13, 2017 · 1 revision

MAILWRITE

NAME:: MailWrite -- Open a new Write window or activate one already opened. (V1.3)

TEMPLATE:: VAR/K,STEM/K,WINDOW/N,QUIET/S

FUNCTION:: Opens a Write window to compose a new mail or activates one already opened.

 Except when replying/forwarding/bouncing email where only one
 Write window is used, MAILWRITE is needed before trying to edit
 any part of a new message.

INPUTS:: VAR/K - alternative variable to put the results into instead of RESULT (V2.0)\ STEM/K - base name used for the stem where the returned data will be stored (V2.0)\ WINDOW/N - change the command behavior to just activate an already opened Write window identified by the supplied parameter\ QUIET/S - force the window to stay invisible (V2.1)\

RETURNS:: VAR - info returned by the command\ <STEM>WINDOW - number of the created/activated window\

 `RC` is set to 5 if `WINDOW` is used with a value referring to an
 inexistant window, or to 10 if the window cannot be opened, maybe
 because the limit of two Write windows has been reached.

NOTES:: Window slots are dinamically assigned as they are required until all of them are occupied, and remain in use until the relevant window is closed (an "invisible" Write window is also "open" within this context). The optional WINDOW parameter sets the active Write window, upon which the WRITEATTACH, WRITEBCC, WRITECC, WRITEEDITOR WRITEFROM, WRITELETTER, WRITEMAILTO, WRITEOPTIONS, WRITEQUEUE, WRITEREPLYTO, WRITESEND, WRITESUBJECT, and WRITETO commands will act when called, though strictly speaking this is only necessary when at least two Write windows are opened at the same time - in that case, MAILWRITE WINDOW x should be called before using any of these commands to ensure they act on the window they are supposed to.

 Regardless, note that manually activating a Write window using the
 GUI does *not* magically make it the target of the above mentioned
 commands.

EXAMPLE:: {{{#!arexx /* Enable result codes */ OPTIONS RESULTS

 /* Start a new mail */
 MAILWRITE STEM st.
 win1 = st.window

 /* Start yet another mail */
 MAILWRITE STEM st.
 win2 = st.window

 /* Edit the first Write window */
 MAILWRITE WINDOW win1
 WRITETO '[email protected]'
 'WRITESUBJECT "I do not think I can go to work today"'
 WRITELETTER 'work:excuses.txt'

 /* Edit the second Write window */
 MAILWRITE WINDOW win2
 WRITETO '[email protected]'
 'WRITESUBJECT "Stuffed at work, I will be late"'

 /* Put the first email in the Outgoing queue */
 MAILWRITE WINDOW win1
 WRITEQUEUE

 /* Start a new email using an invisible Write window */
 MAILWRITE STEM st. QUIET
 win3 = st.window
 WRITETO '[email protected]'
 'WRITESUBJECT "Two with Mozzarella + lots of coke"'
 WRITELETTER 'dh5:priv/Snail_Linda.txt'

 /* Finish editing the second email and send it at once */
 MAILWRITE WINDOW win2
 WRITESEND

 /* Send the third email */
 MAILWRITE WINDOW win3
 WRITEOPTIONS DELETE   /* avoid leaving any traces */
 WRITESEND
 }}}

BUGS:: MAILWRITE would throw Enforcer hits if YAM was iconified and the external editor was configured to be launched immediately, or when the QUIET switch was used; this was fixed in V2.3.

SEE ALSO:: WRITEATTACH, WRITEBCC, WRITECC, WRITEEDITOR WRITEFROM, WRITELETTER, WRITEMAILTO, WRITEOPTIONS, WRITEQUEUE, WRITEREPLYTO, WRITESEND, WRITESUBJECT, WRITETO

Home

Getting Started

Troubleshooting

Advanced use of YAM

Cookbooks

Development

Clone this wiki locally