-
Notifications
You must be signed in to change notification settings - Fork 3
/
ISOThreadUM2.scad
391 lines (354 loc) · 13.1 KB
/
ISOThreadUM2.scad
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
// ISO Metric Thread Implementation
// Trevor Moseley
// 20/04/2014
// For thread dimensions see
// http://en.wikipedia.org/wiki/File:ISO_and_UTS_Thread_Dimensions.svg
$fn=30;
WrenchSizes=0; // =0= Rolson sizes, =1=Fairbury sizes, =2= Small bolt head sizes
//--demo functions--------------------------------------------------------------
//hex_bolt(10,16); // make an M10 x 16 ISO bolt
//hex_bolt_with_thread_in(10,16,6); // make an M10 X 16 ISO bolt with an M6 thread inside the bolt.
//hex_nut(10); // make an M10 ISO nut
//hex_bolt(8,16); // make an M8 x 16 ISO bolt
//hex_nut(8); // make an M8 ISO nut
//hex_bolt(6,12); // make an M6 x 12 ISO bolt
//hex_nut(6); // make an M6 ISO nut
//thread_out(8,16); // make an M8 x 16 ISO thread
//thread_out_centre(8,16); // make a centre for an M8 x 16 ISO thread
//thread_out_pitch(8,16,1.0); // make an M8 x 16 thread with 1 mm pitch
//thread_out_centre_pitch(8,16,0.5); // make the centre for an M8 x 16 thread with 1 mm pitch
//thread_in(8,10); // make an M8 x 10 ISO thread
//thread_in_ring(8,10,2); // make a ring to enclose an M8 x 10 ISO thread with thickness 2 mm
//thread_in_pitch(8,10,1.0); // make an M8 x 10 thread with 1mm pitch
//block_with_thread_in(8,10,16,16); // Make an M8 X 10 thread in a block of 16 x 16
//--pitch-----------------------------------------------------------------------
// function for ISO coarse thread pitch (these are specified by ISO)
function get_coarse_pitch(dia) = lookup(dia, [
[1,0.25],[1.2,0.25],[1.4,0.3],[1.6,0.35],[1.8,0.35],[2,0.4],[2.5,0.45],[3,0.5],[3.5,0.6],[4,0.7],[5,0.8],[6,1],[7,1],[8,1.25],[10,1.5],[12,1.75],[14,2],[16,2],[18,2.5],[20,2.5],[22,2.5],[24,3],[27,3],[30,3.5],[33,3.5],[36,4],[39,4],[42,4.5],[45,4.5],[48,5],[52,5],[56,5.5],[60,5.5],[64,6],[78,5]]);
//--nut dims--------------------------------------------------------------------
// these are NOT specified by ISO
// support is provided for Rolson or Fairbury sizes, see WrenchSizes above
// function for Rolson hex nut diameter from thread size
function rolson_hex_nut_dia(dia) = lookup(dia, [
[3,6.4],[4,8.1],[5,9.2],[6,11.5],[8,16.0],[10,19.6],[12,22.1],[16,27.7],[20,34.6],[24,41.6],[30,53.1],[36,63.5]]);
// function for Rolson hex nut height from thread size
function rolson_hex_nut_hi(dia) = lookup(dia, [
[3,2.4],[4,3.2],[5,4],[6,3],[8,5],[10,5],[12,10],[16,13],[20,16],[24,19],[30,24],[36,29]]);
// function for Fairbury hex nut diameter from thread size
function fairbury_hex_nut_dia(dia) = lookup(dia, [
[3,6.0],[4,7.7],[5,8.8],[6,11.0],[8,14.4],[10,17.8],[12,20.0],[16,26.8],[20,33.0],[24,40.0],[30,50.9],[36,60.8]]);
// function for Fairbury hex nut height from thread size
function fairbury_hex_nut_hi(dia) = lookup(dia, [
[3,2.2],[4,3.0],[5,4.5],[6,5.0],[8,6.5],[10,8.1],[12,10.4],[16,14.2],[20,17],[24,20.3],[30,24.4],[36,29.5]]);
//--bolt dims-------------------------------------------------------------------
// these are NOT specified by ISO
// support is provided for Rolson or Fairbury sizes, see WrenchSizes above
// function for Rolson hex bolt head diameter from thread size
function rolson_hex_bolt_dia(dia) = lookup(dia, [
[3,6.4],[4,8.1],[5,9.2],[6,11.5],[8,14.0],[10,16],[12,22.1],[16,27.7],[20,34.6],[24,41.6],[30,53.1],[36,63.5]]);
// function for Rolson hex bolt head height from thread size
function rolson_hex_bolt_hi(dia) = lookup(dia, [
[3,2.4],[4,3.2],[5,4],[6,3.5],[8,4.5],[10,5],[12,10],[16,13],[20,16],[24,19],[30,24],[36,29]]);
// function for Fairbury hex bolt head diameter from thread size
function fairbury_hex_bolt_dia(dia) = lookup(dia, [
[3,6.4],[4,8.1],[5,8.8],[6,11.1],[8,14.4],[10,17.8],[12,20.1],[16,26.8],[20,33.0],[24,39.6],[30,50.9],[36,60.8]]);
// function for Fairbury hex bolt head height from thread size
function fairbury_hex_bolt_hi(dia) = lookup(dia, [
[3,2.4],[4,3.2],[5,3.4],[6,3.9],[8,5.1],[10,6.2],[12,7.3],[16,9.7],[20,12.2],[24,14.6],[30,17.9],[36,21.7]]);
// function for small hex bolt head diameter from thread size
function small_hex_bolt_dia(dia) = dia * 1.2;
// function for small hex bolt head height from thread size
function small_hex_bolt_hi(dia) = dia * 0.4;
//--top level modules-----------------------------------------------------------
module block_with_thread_in(dia,hi,block_x,block_y)
// Make a block with a threaded hole through its center.
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt, also the height of the block.
// block_x=length of the block.
// block_y=width of the block.
{
//Make the block with a cylinder through its center.
difference()
{
translate([-block_x/2, -block_y/2, 0]) cube(size = [block_x, block_y, hi]);
translate([0,0,-1]) cylinder(r = (dia/2),h = hi+2);
}
thread_in(dia, hi); //Add the thread.
}
module hex_bolt_with_thread_in(dia,hi,diaThreadIn)
// make an ISO bolt
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt
// diaThreadIn=diameter of the thread inside
{
if (dia > diaThreadIn + 1)
{
//We need to know the height of the bolt head so we can offset the threaded hole because the bolt head is at the bottom, near Z=0.
heightBoltHead = 0; //Normally, it can't be set to 0;
heightBoltHead = WrenchSizes == 0 ? rolson_hex_bolt_hi(dia) : 0;
heightBoltHead = (heightBoltHead != 0 && WrenchSizes == 1) ? fairbury_hex_bolt_hi(dia) : 0;
heightBoltHead = (heightBoltHead != 0 && WrenchSizes == 2) ? small_hex_bolt_hi(dia) : 0;
//Make the bolt with the cylinder inside of it.
difference()
{
if (WrenchSizes==0) rolson_hex_bolt(dia,hi);
else if (WrenchSizes==1) fairbury_hex_bolt(dia,hi);
else small_hex_bolt(dia,hi);
translate([0,0,heightBoltHead]) cylinder(r = (diaThreadIn/2),h = hi+0.1);
}
translate([0,0,heightBoltHead]) thread_in(diaThreadIn,hi-0.2); //Add the thread.
//Debug, to see if the smaller bolt will fit.
//rotate([180,0,0]) translate([0,0,-heightBoltHead-hi-2]) small_hex_bolt(diaThreadIn,hi);
}
else
{
echo("The diameter for the thread inside (",diaThreadIn,") + 1 cannot be equal or higher than the diameter of the bolt (",dia,")!");
}
}
module hex_bolt(dia,hi)
// make an ISO bolt
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt
{
if (WrenchSizes==0) rolson_hex_bolt(dia,hi);
else if (WrenchSizes==1) fairbury_hex_bolt(dia,hi);
else small_hex_bolt(dia,hi);
}
module hex_nut(dia,hi)
// make an ISO nut
// dia=diameter, 6=M6 etc.
{
if (WrenchSizes==0) rolson_hex_nut(dia);
else fairbury_hex_nut(dia);
}
module thread_out(dia,hi,thr=$fn)
// make an outside ISO thread (as used on a bolt)
// dia=diameter, 6=M6 etc
// hi=height, 10=make a 10mm long thread
// thr=thread quality, 10=make a thread with 10 segments per turn
{
p = get_coarse_pitch(dia);
thread_out_pitch(dia,hi,p,thr);
}
module thread_in(dia,hi,thr=$fn)
// make an inside thread (as used on a nut)
// dia = diameter, 6=M6 etc
// hi = height, 10=make a 10mm long thread
// thr = thread quality, 10=make a thread with 10 segments per turn
{
p = get_coarse_pitch(dia);
thread_in_pitch(dia,hi,p,thr);
}
module thread_out_pitch(dia,hi,p,thr=$fn)
// make an outside thread (as used on a bolt) with supplied pitch
// dia=diameter, 6=M6 etc
// hi=height, 10=make a 10mm long thread
// p=pitch
// thr=thread quality, 10=make a thread with 10 segments per turn
{
h=(cos(30)*p)/8;
Rmin=(dia/2)-(5*h); // as wiki Dmin
s=360/thr; // length of segment in degrees
t1=(hi-p)/p; // number of full turns
r=t1%1.0; // length remaining (not full turn)
t=t1-r; // integer number of full turns
n=r/(p/thr); // number of segments for remainder
// do full turns
for(tn=[0:t-1])
translate([0,0,tn*p]) th_out_turn(dia,p,thr);
// do remainder
for(sg=[0:n])
th_out_pt(Rmin,p,s,sg+(t*thr),thr,h,p/thr);
}
module thread_in_pitch(dia,hi,p,thr=$fn)
// make an inside thread (as used on a nut)
// dia = diameter, 6=M6 etc
// hi = height, 10=make a 10mm long thread
// p=pitch
// thr = thread quality, 10=make a thread with 10 segments per turn
{
h=(cos(30)*p)/8;
Rmin=(dia/2)-(5*h); // as wiki Dmin
s=360/thr; // length of segment in degrees
t1=(hi-p)/p; // number of full turns
r=t1%1.0; // length remaining (not full turn)
t=t1-r; // integer number of turns
n=r/(p/thr); // number of segments for remainder
for(tn=[0:t-1])
translate([0,0,tn*p]) th_in_turn(dia,p,thr);
for(sg=[0:n])
th_in_pt(Rmin+0.1,p,s,sg+(t*thr),thr,h,p/thr);
}
module thread_out_centre(dia,hi)
{
p = get_coarse_pitch(dia);
thread_out_centre_pitch(dia,hi,p);
}
module thread_out_centre_pitch(dia,hi,p)
{
h = (cos(30)*p)/8;
Rmin = (dia/2) - (5*h); // as wiki Dmin
cylinder(r = Rmin, h = hi);
}
module thread_in_ring(dia,hi,thk)
{
difference()
{
cylinder(r = (dia/2)+0.5,h = hi);
translate([0,0,-1]) cylinder(r = (dia/2)+0.1, h = hi+thk);
}
}
//--low level modules-----------------------------------------------------------
module rolson_hex_bolt(dia,hi)
// make an ISO bolt with Rolson wrench sizes
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt
{
hhi = rolson_hex_bolt_hi(dia);
cylinder(r = rolson_hex_bolt_dia(dia)/2,h = hhi, $fn=6);
translate([0,0,hhi-0.1]) thread_out(dia,hi+0.1);
translate([0,0,hhi-0.1]) thread_out_centre(dia,hi+0.1);
}
module fairbury_hex_bolt(dia,hi)
// make an ISO bolt with Fairbury wrench sizes
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt
{
hhi = fairbury_hex_bolt_hi(dia);
cylinder(r = fairbury_hex_bolt_dia(dia)/2,h = hhi, $fn=6);
translate([0,0,hhi-0.1]) thread_out(dia,hi+0.1);
translate([0,0,hhi-0.1]) thread_out_centre(dia,hi+0.1);
}
module small_hex_bolt(dia,hi)
// make an ISO bolt with Fairbury wrench sizes
// dia=diameter, 6=M6 etc.
// hi=length of threaded part of bolt
{
hhi = small_hex_bolt_hi(dia);
cylinder(r = small_hex_bolt_dia(dia)/2,h = hhi, $fn=6);
translate([0,0,hhi-0.1]) thread_out(dia,hi+0.1);
translate([0,0,hhi-0.1]) thread_out_centre(dia,hi+0.1);
}
module rolson_hex_nut(dia)
// make an ISO nut with Rolson wrench sizes
// dia=diameter, 6=M6 etc.
{
hi = rolson_hex_nut_hi(dia);
difference()
{
cylinder(r = rolson_hex_nut_dia(dia)/2,h = hi, $fn=6);
translate([0,0,-0.1]) cylinder(r = dia/2+0.1, h =hi + 0.2);
}
translate([0,0,0.1]) thread_in(dia,hi-0.2);
}
module fairbury_hex_nut(dia)
// make an ISO nut with Fairbury wrench sizes
// dia=diameter, 6=M6 etc.
{
hi = fairbury_hex_nut_hi(dia);
difference()
{
cylinder(r = fairbury_hex_nut_dia(dia)/2,h = hi, $fn=6);
translate([0,0,-0.1]) cylinder(r = dia/2+0.1, h =hi + 0.2);
}
translate([0,0,0.1]) thread_in(dia,hi-0.2);
}
module th_out_turn(dia,p,thr=$fn)
// make a single turn of an outside thread
// dia=diameter, 6=M6 etc
// p=pitch
// thr=thread quality, 10=make a thread with 10 segments per turn
{
h = (cos(30)*p)/8;
Rmin = (dia/2) - (5*h); // as wiki Dmin
s = 360/thr;
for(sg=[0:thr-1])
th_out_pt(Rmin,p,s,sg,thr,h,p/thr);
}
module th_out_pt(rt,p,s,sg,thr,h,sh)
// make a part of an outside thread (single segment)
// rt = radius of thread (nearest centre)
// p = pitch
// s = segment length (degrees)
// sg = segment number
// thr = segments in circumference
// h = ISO h of thread / 8
// sh = segment height (z)
{
as = (sg % thr) * s; // angle to start of seg
ae = as + s; // angle to end of seg (with overlap)
z = sh*sg;
//pp = p/2;
// 1,4
// |\
// | \ 2,5
// | /
// |/
// 0,3
// view from front (x & z) extruded in y by sg
//
//echo(str("as=",as,", ae=",ae," z=",z));
polyhedron(
points = [
[cos(as)*rt,sin(as)*rt,z], // 0
[cos(as)*rt,sin(as)*rt,z+(3/4*p)], // 1
[cos(as)*(rt+(5*h)),sin(as)*(rt+(5*h)),z+(3/8*p)], // 2
[cos(ae)*rt,sin(ae)*rt,z+sh], // 3
[cos(ae)*rt,sin(ae)*rt,z+(3/4*p)+sh], // 4
[cos(ae)*(rt+(5*h)),sin(ae)*(rt+(5*h)),z+sh+(3/8*p)]], // 5
faces = [
[0,1,2], // near face
[3,5,4], // far face
[0,3,4],[0,4,1], // left face
[0,5,3],[0,2,5], // bottom face
[1,4,5],[1,5,2]]); // top face
}
module th_in_turn(dia,p,thr=$fn)
// make an single turn of an inside thread
// dia = diameter, 6=M6 etc
// p=pitch
// thr = thread quality, 10=make a thread with 10 segments per turn
{
h = (cos(30)*p)/8;
Rmin = (dia/2) - (5*h); // as wiki Dmin
s = 360/thr;
for(sg=[0:thr-1])
th_in_pt(Rmin+0.1,p,s,sg,thr,h,p/thr);
}
module th_in_pt(rt,p,s,sg,thr,h,sh)
// make a part of an inside thread (single segment)
// rt = radius of thread (nearest centre)
// p = pitch
// s = segment length (degrees)
// sg = segment number
// thr = segments in circumference
// h = ISO h of thread / 8
// sh = segment height (z)
{
as = ((sg % thr) * s - 180); // angle to start of seg
ae = as + s; // angle to end of seg (with overlap)
z = sh*sg;
pp = p/2;
// 2,5
// /|
// 1,4 / |
// \ |
// \|
// 0,3
// view from front (x & z) extruded in y by sg
//
polyhedron(
points = [
[cos(as)*(rt+(5*h)),sin(as)*(rt+(5*h)),z], //0
[cos(as)*rt,sin(as)*rt,z+(3/8*p)], //1
[cos(as)*(rt+(5*h)),sin(as)*(rt+(5*h)),z+(3/4*p)], //2
[cos(ae)*(rt+(5*h)),sin(ae)*(rt+(5*h)),z+sh], //3
[cos(ae)*rt,sin(ae)*rt,z+(3/8*p)+sh], //4
[cos(ae)*(rt+(5*h)),sin(ae)*(rt+(5*h)),z+(3/4*p)+sh]], //5
faces = [
[0,1,2], // near face
[3,5,4], // far face
[0,3,4],[0,4,1], // left face
[0,5,3],[0,2,5], // bottom face
[1,4,5],[1,5,2]]); // top face
}