Change_Interval.ino

/****************************************************************************************************************************
  Change_Interval.ino
  
  For RP2040-based boards such as RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040 and GENERIC_RP2040.
  Written by Khoi Hoang

  Built by Khoi Hoang https://github.com/khoih-prog/TimerInterrupt_Generic
  Licensed under MIT license

  The RPI_PICO system timer peripheral provides a global microsecond timebase for the system, and generates
  interrupts based on this timebase. It supports the following features:
    • A single 64-bit counter, incrementing once per microsecond
    • This counter can be read from a pair of latching registers, for race-free reads over a 32-bit bus.
    • Four alarms: match on the lower 32 bits of counter, IRQ on match: TIMER_IRQ_0-TIMER_IRQ_3

  Now even you use all these new 16 ISR-based timers,with their maximum interval practically unlimited (limited only by
  unsigned long miliseconds), you just consume only one RPI_PICO timer and avoid conflicting with other cores' tasks.
  The accuracy is nearly perfect compared to software timers. The most important feature is they're ISR-based timers
  Therefore, their executions are not blocked by bad-behaving functions / tasks.
  This important feature is absolutely necessary for mission-critical tasks.

  Based on SimpleTimer - A timer library for Arduino.
  Author: mromani@ottotecnica.com
  Copyright (c) 2010 OTTOTECNICA Italy

  Based on BlynkTimer.h
  Author: Volodymyr Shymanskyy
*****************************************************************************************************************************/

/*
   Notes:
   Special design is necessary to share data between interrupt code and the rest of your program.
   Variables usually need to be "volatile" types. Volatile tells the compiler to avoid optimizations that assume
   variable can not spontaneously change. Because your function may change variables while your program is using them,
   the compiler needs this hint. But volatile alone is often not enough.
   When accessing shared variables, usually interrupts must be disabled. Even with volatile,
   if the interrupt changes a multi-byte variable between a sequence of instructions, it can be read incorrectly.
   If your data is multiple variables, such as an array and a count, usually interrupts need to be disabled
   or the entire sequence of your code which accesses the data.
*/

// These define's must be placed at the beginning before #include "TimerInterrupt_Generic.h"
// _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4
// Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.
#define TIMER_INTERRUPT_DEBUG         1
#define _TIMERINTERRUPT_LOGLEVEL_     4

#include "TimerInterrupt_Generic.h"

#ifndef LED_BUILTIN
  #define LED_BUILTIN       25         // Pin D2 mapped to pin GPIO2/ADC12 of ESP32, control on-board LED
#endif

#define PIN_D1              1         // Pin D1 mapped to pin GPIO1 of RPI_PICO

volatile uint32_t Timer0Count = 0;
volatile uint32_t Timer1Count = 0;

bool TimerHandler0(struct repeating_timer *t)
{ 
  static bool toggle0 = false;

  // Flag for checking to be sure ISR is working as Serial.print is not OK here in ISR
  Timer0Count++;

#if (TIMER_INTERRUPT_DEBUG > 0)
  Serial.print("ITimer0: millis() = "); Serial.println(millis());
#endif

  //timer interrupt toggles pin LED_BUILTIN
  digitalWrite(LED_BUILTIN, toggle0);
  toggle0 = !toggle0;

  return true;
}

bool TimerHandler1(struct repeating_timer *t)
{ 
  static bool toggle1 = false;

  // Flag for checking to be sure ISR is working as Serial.print is not OK here in ISR
  Timer1Count++;

#if (TIMER_INTERRUPT_DEBUG > 0)
  Serial.print("ITimer1: millis() = "); Serial.println(millis());
#endif

  //timer interrupt toggles PIN_D1
  digitalWrite(PIN_D1, toggle1);
  toggle1 = !toggle1;

  return true;
}

void printResult(uint32_t currTime)
{
  Serial.print(F("Time = ")); Serial.print(currTime); 
  Serial.print(F(", Timer0Count = ")); Serial.print(Timer0Count);
  Serial.print(F(", Timer1Count = ")); Serial.println(Timer1Count);
}

#define TIMER0_INTERVAL_MS        2000

#define TIMER1_INTERVAL_MS        5000

// Init ESP32 timer 0
RPI_PICO_Timer ITimer0(0);
RPI_PICO_Timer ITimer1(1);

void setup()
{
  pinMode(LED_BUILTIN,  OUTPUT);
  pinMode(PIN_D1,       OUTPUT);
  
  Serial.begin(115200);
  while (!Serial);

  delay(100);

  Serial.print(F("\nStarting Change_Interval on ")); Serial.println(BOARD_NAME);
  Serial.println(RPI_PICO_TIMER_INTERRUPT_VERSION);
  Serial.println(TIMER_INTERRUPT_GENERIC_VERSION);
  Serial.print(F("CPU Frequency = ")); Serial.print(F_CPU / 1000000); Serial.println(F(" MHz"));

  // Interval in microsecs
  if (ITimer0.attachInterruptInterval(TIMER0_INTERVAL_MS * 1000, TimerHandler0))
  {
    Serial.print(F("Starting  ITimer0 OK, millis() = ")); Serial.println(millis());
  }
  else
    Serial.println(F("Can't set ITimer0. Select another freq. or timer"));

  // Interval in microsecs
  if (ITimer1.attachInterruptInterval(TIMER1_INTERVAL_MS * 1000, TimerHandler1))
  {
    Serial.print(F("Starting  ITimer1 OK, millis() = ")); Serial.println(millis());
  }
  else
    Serial.println(F("Can't set ITimer1. Select another freq. or timer"));
}

#define CHECK_INTERVAL_MS     10000L
#define CHANGE_INTERVAL_MS    20000L

void loop()
{
  static uint32_t lastTime = 0;
  static uint32_t lastChangeTime = 0;
  static uint32_t currTime;
  static uint32_t multFactor = 0;

  currTime = millis();

  if (currTime - lastTime > CHECK_INTERVAL_MS)
  {
    printResult(currTime);
    lastTime = currTime;

    if (currTime - lastChangeTime > CHANGE_INTERVAL_MS)
    {
      //setInterval(unsigned long interval, timerCallback callback)
      multFactor = (multFactor + 1) % 2;
      
      ITimer0.setInterval(TIMER0_INTERVAL_MS * 1000 * (multFactor + 1), TimerHandler0);
      ITimer1.setInterval(TIMER1_INTERVAL_MS * 1000 * (multFactor + 1), TimerHandler1);

      Serial.print(F("Changing Interval, Timer0 = ")); Serial.print(TIMER0_INTERVAL_MS * (multFactor + 1));
      Serial.print(F(",  Timer1 = ")); Serial.println(TIMER1_INTERVAL_MS * (multFactor + 1)); 

      lastChangeTime = currTime;
    }
  }
}