forked from Nikolay-Kha/PyCNC
-
Notifications
You must be signed in to change notification settings - Fork 0
/
config.py
94 lines (79 loc) · 2.9 KB
/
config.py
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
# -----------------------------------------------------------------------------
# Hardware config.
# Maximum velocity for each axis in millimeter per minute.
MAX_VELOCITY_MM_PER_MIN_X = 24000
MAX_VELOCITY_MM_PER_MIN_Y = 12000
MAX_VELOCITY_MM_PER_MIN_Z = 600
MAX_VELOCITY_MM_PER_MIN_E = 1500
MIN_VELOCITY_MM_PER_MIN = 1
# Average velocity for endstop calibration procedure
CALIBRATION_VELOCITY_MM_PER_MIN = 300
# Stepper motors steps per millimeter for each axis.
STEPPER_PULSES_PER_MM_X = 100
STEPPER_PULSES_PER_MM_Y = 100
STEPPER_PULSES_PER_MM_Z = 400
STEPPER_PULSES_PER_MM_E = 150
# Invert axises direction, by default(False) high level means increase of
# position. For inverted(True) axis, high level means decrease of position.
STEPPER_INVERTED_X = True
STEPPER_INVERTED_Y = False
STEPPER_INVERTED_Z = False
STEPPER_INVERTED_E = True
# Invert zero end stops switches. By default(False) low level on input pin
# means that axis in zero position. For inverted(True) end stops, high level
# means zero position.
ENDSTOP_INVERTED_X = True
ENDSTOP_INVERTED_Y = True
ENDSTOP_INVERTED_Z = False # Auto leveler
# Workplace physical size.
TABLE_SIZE_X_MM = 200
TABLE_SIZE_Y_MM = 200
TABLE_SIZE_Z_MM = 220
# Mixed settings.
STEPPER_PULSE_LENGTH_US = 2
STEPPER_MAX_ACCELERATION_MM_PER_S2 = 3000 # for all axis, mm per sec^2
SPINDLE_MAX_RPM = 10000
EXTRUDER_MAX_TEMPERATURE = 250
BED_MAX_TEMPERATURE = 100
MIN_TEMPERATURE = 40
EXTRUDER_PID = {"P": 0.059161177519,
"I": 0.00206217171374,
"D": 0.206217171374}
BED_PID = {"P": 0.226740848076,
"I": 0.00323956215053,
"D": 0.323956215053}
# -----------------------------------------------------------------------------
# Pins configuration.
# Enable pin for all steppers, low level is enabled.
STEPPERS_ENABLE_PIN = 26
STEPPER_STEP_PIN_X = 21
STEPPER_STEP_PIN_Y = 16
STEPPER_STEP_PIN_Z = 12
STEPPER_STEP_PIN_E = 8
STEPPER_DIR_PIN_X = 20
STEPPER_DIR_PIN_Y = 19
STEPPER_DIR_PIN_Z = 13
STEPPER_DIR_PIN_E = 7
SPINDLE_PWM_PIN = 4
FAN_PIN = 27
EXTRUDER_HEATER_PIN = 18
BED_HEATER_PIN = 22
EXTRUDER_TEMPERATURE_SENSOR_CHANNEL = 2
BED_TEMPERATURE_SENSOR_CHANNEL = 1
ENDSTOP_PIN_X = 23
ENDSTOP_PIN_Y = 10
ENDSTOP_PIN_Z = 25
# -----------------------------------------------------------------------------
# Behavior config
# Run command immediately after receiving and stream new pulses, otherwise
# buffer will be prepared firstly and then command will run.
# Before enabling this feature, please make sure that board performance is
# enough for streaming pulses(faster then real time).
INSTANT_RUN = True
# If this parameter is False, error will be raised on command with velocity
# more than maximum velocity specified here. If this parameter is True,
# velocity would be decreased(proportional for all axises) to fit the maximum
# velocity.
AUTO_VELOCITY_ADJUSTMENT = True
# Automatically turn on fan when extruder is heating, boolean value.
AUTO_FAN_ON = True