A simple Ansible role to configure a GPS based NTP Server which can deliver a time signal to a network that is not connected to the internet.
This build uses a Raspberry Pi and time signals derived from a connected GPS device.
Designed and tested with:
- Raspberry Pi 3 Model B V1.2 running minimal version of Raspbian Stretch.
- Adafruit Ultimate GPS Breakout V3 board
Wiring connections:
from Raspi pin: 4 (+5V) to GPS Breakout pin: VIN +5V
from Raspi pin: 6 (Ground) to GPS Breakout pin: GND Gnd
from Raspi pin: 8 (TXD0) (GPIO14) to GPS Breakout pin: RX TX
from Raspi pin: 10 (RXD0) (GPIO15) to GPS Breakout pin: TX RX
from Raspi pin: 12 (GPIO18) to GPS Breakout pin: PPS (Pulses Per Second)
None.
A set of default templates for cmdline.txt, dhclient.conf, ntp.conf,
config.txt, and gpsd are provided in the templates subdirectory of this role.
They should work fine for most applications. Should local conditions dictate, you
may optionally override them by putting equivalent-named files in
{{ inventory_dir }}/templates.
None.
Create playbook, tinaja-ntp-gps.yml:
- hosts: ntpserver
roles:
- { role: tinaja.ntp-gps }
- Install Ansible - will assume this is already done...
- Download the latest version of the Raspbian image from: https://downloads.raspberrypi.org/raspbian_lite_latest
- Burn the image on a MicroSD card (8G or more) using etcher
- Add a magic empty file named SSH onto the boot partition (configures default SSH service)
- Plug in the MicroSD image into the Raspi and boot up.
- After bootup, copy your public key to the raspberrypi using user:pi, password:raspberry:
$ ssh-copy-id -f -i ~/.ssh/id_rsa.pub [email protected]
- Setup a host inventory file with a reference like this:
tinaja-ntp ansible_host=<raspi ipaddress> ansible_user=pi
- Run your playbook:
$ ansible-playbook tinaja-ntp-gps.yml -i hosts/hosts.ini -u pi -b -c ssh
Run these tests after rebooting:
Log into your raspi:
$ ssh [email protected]
Escalate to user, root:
# sudo su -
See the serial data streaming in from the GPS device
# cat /dev/ttyAMA0
See the /dev/pps0 device streaming in
# ppstest /dev/pps0
See the gps device statistics including the time, Latitude, Longitude from the GPS receiver
# gpsmon
See the list of ntp servers. The PPS reference should have an asterisk indicating the primary source.
# ntpq -p
*SHM(2) .PPS. 0 l 1 64 377 0.000 -51.298 4.627
On your local server
Set up the NTP server to point to the new NTP server. Edit /etc/ntp.cfg:
# nano /etc/ntp.conf
Change this:
# You do need to talk to an NTP server or two (or three).
#server ntp.your-provider.example
to this:
# You do need to talk to an NTP server or two (or three).
#server ntp.your-provider.example
server <your ntp server ip or fqdn>
Save the file and restart the NTP service:
# systemctl restart ntp.service
See the magic, by running this command:
# date
- How Ansible Works - https://www.ansible.com/overview/how-ansible-works
- Get Started with Ansible - https://docs.ansible.com/ansible/latest/network/getting_started/first_playbook.html
- NTP - https://en.wikipedia.org/wiki/Network_Time_Protocol
- Raspberry Pi GPS Time - http://unixwiz.net/techtips/raspberry-pi3-gps-time.html
- Raspberry Pi NTP - https://www.satsignal.eu/ntp/Raspberry-Pi-NTP.html
- Stratum-1 NTP Server using Raspberry Pi - https://developers.redhat.com/blog/2017/02/22/how-to-build-a-stratum-1-ntp-server-using-a-raspberry-pi/
- Adafruit Ultimate GPS - https://learn.adafruit.com/adafruit-ultimate-gps
MIT
Chris Jefferies - [email protected]