diff --git a/code/components/jomjol_controlcamera/ClassControllCamera.cpp b/code/components/jomjol_controlcamera/ClassControllCamera.cpp
index 8b325d0cc..5aee2ddda 100644
--- a/code/components/jomjol_controlcamera/ClassControllCamera.cpp
+++ b/code/components/jomjol_controlcamera/ClassControllCamera.cpp
@@ -963,10 +963,17 @@ void CCamera::setStatusLED(bool _status)
         /* Set the GPIO as a push/pull output */
         gpio_set_direction(GPIO_STATUS_LED_ONBOARD, GPIO_MODE_OUTPUT);
 
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
         if (!_status)
             gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
         else
             gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#else
+        if (_status)
+            gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
+        else
+            gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#endif
     }
 }
 
diff --git a/code/components/jomjol_helper/statusled.cpp b/code/components/jomjol_helper/statusled.cpp
index 5f8e7c87a..5d97db1df 100644
--- a/code/components/jomjol_helper/statusled.cpp
+++ b/code/components/jomjol_helper/statusled.cpp
@@ -25,7 +25,11 @@ void task_StatusLED(void *pvParameter)
 
 		esp_rom_gpio_pad_select_gpio(GPIO_STATUS_LED_ONBOARD); // Init the GPIO
 		gpio_set_direction(GPIO_STATUS_LED_ONBOARD, GPIO_MODE_OUTPUT); // Set the GPIO as a push/pull output
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 		gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);// LED off
+#else
+		gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);// LED off
+#endif
 
 		for (int i=0; i<2; ) // Default: repeat 2 times
 		{
@@ -34,9 +38,17 @@ void task_StatusLED(void *pvParameter)
 
 			for (int j = 0; j < StatusLEDDataInt.iSourceBlinkCnt; ++j)
 			{
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#else
+				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
+#endif
 				vTaskDelay(StatusLEDDataInt.iBlinkTime / portTICK_PERIOD_MS);
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
+#else
+				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#endif
 				vTaskDelay(StatusLEDDataInt.iBlinkTime / portTICK_PERIOD_MS);
 			}
 
@@ -44,9 +56,17 @@ void task_StatusLED(void *pvParameter)
 
 			for (int j = 0; j < StatusLEDDataInt.iCodeBlinkCnt; ++j)
 			{
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#else
+				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
+#endif
 				vTaskDelay(StatusLEDDataInt.iBlinkTime / portTICK_PERIOD_MS);
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);
+#else
+				gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);
+#endif
 				vTaskDelay(StatusLEDDataInt.iBlinkTime / portTICK_PERIOD_MS);
 			}
 			vTaskDelay(1500 / portTICK_PERIOD_MS);	// Delay to signal new round
@@ -147,5 +167,9 @@ void StatusLEDOff(void)
 
 	esp_rom_gpio_pad_select_gpio(GPIO_STATUS_LED_ONBOARD); // Init the GPIO
 	gpio_set_direction(GPIO_STATUS_LED_ONBOARD, GPIO_MODE_OUTPUT); // Set the GPIO as a push/pull output
+#ifdef GPIO_STATUS_LED_ONBOARD_ACTIVELOW
 	gpio_set_level(GPIO_STATUS_LED_ONBOARD, 1);// LED off
+#else
+	gpio_set_level(GPIO_STATUS_LED_ONBOARD, 0);// LED off
+#endif
 }
\ No newline at end of file
diff --git a/code/include/defines.h b/code/include/defines.h
index 7293b9e84..55f8173cc 100644
--- a/code/include/defines.h
+++ b/code/include/defines.h
@@ -365,7 +365,8 @@ CONFIG_WPA_11R_SUPPORT=n
 
     // LEDs
     //-------------------------------------------------
-    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_33     // Onboard red status LED
+    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_33     // Onboard status LED (red, active low)
+    #define GPIO_STATUS_LED_ONBOARD_ACTIVELOW
     #define GPIO_FLASHLIGHT_ONBOARD         GPIO_NUM_4      // Onboard flashlight LED
 
     #ifdef BOARD_SDCARD_SDMMC_BUS_WIDTH_1
@@ -442,7 +443,8 @@ CONFIG_WPA_11R_SUPPORT=n
 
     // LEDs
     //-------------------------------------------------
-    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_21     // Onboard yellow status LED (USER LED)
+    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_21     // Onboard yellow status LED (USER LED, yellow, active low)
+    #define GPIO_STATUS_LED_ONBOARD_ACTIVELOW
     #define GPIO_FLASHLIGHT_ONBOARD         GPIO_NUM_NC     // No onboard flashlight available
 
     #define GPIO_FLASHLIGHT_DEFAULT         GPIO_NUM_1      // Default flashlight GPIO pin (can be modified by activiating GPIO functionality in WebUI)
@@ -507,7 +509,8 @@ CONFIG_WPA_11R_SUPPORT=n
 
     // LEDs
     //-------------------------------------------------
-    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_2     // Onboard status LED
+    #define GPIO_STATUS_LED_ONBOARD         GPIO_NUM_2     // Onboard status LED (blue, active high)
+    //#define GPIO_STATUS_LED_ONBOARD_ACTIVELOW
     #define GPIO_FLASHLIGHT_ONBOARD         GPIO_NUM_48    // Onboard flashlight (WS2812)
 
     #define GPIO_FLASHLIGHT_DEFAULT         GPIO_FLASHLIGHT_ONBOARD // Default flashlight GPIO pin (can be modified by activiating GPIO functionality in WebUI)