diff --git a/boards/btt-kraken/config.cfg b/boards/btt-kraken/config.cfg index f0c1eb11..ddb4e010 100644 --- a/boards/btt-kraken/config.cfg +++ b/boards/btt-kraken/config.cfg @@ -10,7 +10,7 @@ aliases: # steppers (Motor 1-2: X, Y, Motor 4-8: Z3, E, Z0, Z1, Z2, Motor 3: unused) x_step_pin=PC14, x_dir_pin=PC13, x_enable_pin=PE6, x_uart_pin=PD6, x_diag_pin=PC15, x_endstop_pin=PC15, y_step_pin=PE5, y_dir_pin=PE4, y_enable_pin=PE3, y_uart_pin=PD6, y_diag_pin=PF0, y_endstop_pin=PF0, - z0_step_pin=PG11, z0_dir_pin=PD7, z0_enable_pin=PG12, z0_uart_pin=PA15, z0_diag_pin=PF4, z_endstop_pin=PF4, + z0_step_pin=PG11, z0_dir_pin=PD7, z0_enable_pin=PG12, z0_uart_pin=PA15, z0_diag_pin=PF4, z_endstop_pin=PC0, z1_step_pin=PB4, z1_dir_pin=PB3, z1_enable_pin=PB5, z1_uart_pin=PA9, z1_diag_pin=PF10, z2_step_pin=PG15, z2_dir_pin=PB6, z2_enable_pin=PG14, z2_uart_pin=PA10, z2_diag_pin=PC0, z3_step_pin=PG9, z3_dir_pin=PG10, z3_enable_pin=PG13, z3_uart_pin=PD2, z3_diag_pin=PF1, # Voron 2.4 support motor 4 @@ -23,6 +23,10 @@ aliases: # auto leveling bltouch_sensor_pin=PG1, bltouch_control_pin=PE9, probe_pin=PG1, +# VAOC pins + vaoc_probe_pin=PF1 + vaoc_neopixel_pin=PF12 + vaoc_fan_pin=PA3 # fan 3 # 2p fans fan_part_cooling_pin=PA0, fan_toolhead_cooling_pin=PA1, diff --git a/boards/btt-manta-e3ez/config.cfg b/boards/btt-manta-e3ez/config.cfg index ca4bcca2..eebabcb0 100644 --- a/boards/btt-manta-e3ez/config.cfg +++ b/boards/btt-manta-e3ez/config.cfg @@ -10,9 +10,9 @@ aliases: # steppers x_step_pin=PA14, x_dir_pin=PA10, x_enable_pin=PA13, x_uart_pin=PB8, x_diag_pin=PC4, x_endstop_pin=PC5, - y_step_pin=PC8, y_dir_pin=PA15, y_enable_pin=PC14, y_uart_pin=PC9, y_diag_pin=PB0, y_endstop_pin=PB1, - z0_step_pin=PD2, z0_dir_pin=PD4, z0_enable_pin=PD3, z0_uart_pin=PD0, z0_diag_pin=null, - e_step_pin=PB7, e_dir_pin=PB6, e_enable_pin=PB4, e_uart_pin=PB5, e_diag_pin=null, e_heater_pin=PB11, e_sensor_pin=PA4, + y_step_pin=PC8, y_dir_pin=PA15, y_enable_pin=PC14, y_uart_pin=PC9, y_diag_pin=PB0, y_endstop_pin=PB1, + z0_step_pin=PD2, z0_dir_pin=PD4, z0_enable_pin=PD3, z0_uart_pin=PD0, z0_diag_pin=null, z_endstop_pin=PC6, + e_step_pin=PB7, e_dir_pin=PB6, e_enable_pin=PB4, e_uart_pin=PB5, e_diag_pin=null, e_heater_pin=PB11, e_sensor_pin=PA4, stepper_spi_mosi_pin=PC12, stepper_spi_miso_pin=PC11, stepper_spi_sclk_pin=PC10, # accel adxl345_cs_pin=PC15, diff --git a/boards/btt-manta-m4p-22/config.cfg b/boards/btt-manta-m4p-22/config.cfg index 7af9f8b8..f9ccea8d 100644 --- a/boards/btt-manta-m4p-22/config.cfg +++ b/boards/btt-manta-m4p-22/config.cfg @@ -11,8 +11,6 @@ aliases: x_step_pin=PC6, x_dir_pin=PA14, x_enable_pin=PC7, x_uart_pin=PB12, x_diag_pin=PC0, x_endstop_pin=PC0, y_step_pin=PB10, y_dir_pin=PB2, y_enable_pin=PB11, y_uart_pin=PC10, y_diag_pin=PC1, y_endstop_pin=PC1, z0_step_pin=PB0, z0_dir_pin=PC5, z0_enable_pin=PB1, z0_uart_pin=PC9, z0_diag_pin=PC2, z_endstop_pin=PC2, - z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, - z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PB3, e_dir_pin=PB4, e_enable_pin=PD5, e_uart_pin=PA13, e_diag_pin=null, e_heater_pin=PC8, e_sensor_pin=PA0, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # accel diff --git a/boards/btt-manta-m4p/config.cfg b/boards/btt-manta-m4p/config.cfg index ca930746..76bdc8d0 100644 --- a/boards/btt-manta-m4p/config.cfg +++ b/boards/btt-manta-m4p/config.cfg @@ -10,7 +10,7 @@ aliases: # steppers x_step_pin=PC6, x_dir_pin=PA14, x_enable_pin=PC7, x_uart_pin=PB12, x_diag_pin=PC0, x_endstop_pin=PC0, y_step_pin=PB10, y_dir_pin=PB2, y_enable_pin=PB11, y_uart_pin=PC10, y_diag_pin=PC1, y_endstop_pin=PC1, - z0_step_pin=PB0, z0_dir_pin=PC5, z0_enable_pin=PB1, z0_uart_pin=PC9, z0_diag_pin=null, + z0_step_pin=PB0, z0_dir_pin=PC5, z0_enable_pin=PB1, z0_uart_pin=PC9, z0_diag_pin=null, z_endstop_pin=PC2, e_step_pin=PB3, e_dir_pin=PB4, e_enable_pin=PD5, e_uart_pin=PA13, e_diag_pin=null, e_heater_pin=PC8, e_sensor_pin=PA0, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # accel diff --git a/boards/btt-manta-m5p/config.cfg b/boards/btt-manta-m5p/config.cfg index 16d2d1b0..b00fd513 100644 --- a/boards/btt-manta-m5p/config.cfg +++ b/boards/btt-manta-m5p/config.cfg @@ -10,7 +10,7 @@ aliases: # steppers x_step_pin=PC8, x_dir_pin=PC9, x_enable_pin=PA15, x_uart_pin=PD9, x_diag_pin=PD3, x_endstop_pin=PD3, y_step_pin=PA10, y_dir_pin=PA14, y_enable_pin=PA13, y_uart_pin=PD8, y_diag_pin=PD2, y_endstop_pin=PD2, - z0_step_pin=PC6, z0_dir_pin=PC7, z0_enable_pin=PA9, z0_uart_pin=PB10, z0_diag_pin=null, + z0_step_pin=PC6, z0_dir_pin=PC7, z0_enable_pin=PA9, z0_uart_pin=PB10, z0_diag_pin=null, z_endstop_pin=PC3, e_step_pin=PB0, e_dir_pin=PB1, e_enable_pin=PC4, e_uart_pin=PA6, e_diag_pin=null, e_heater_pin=PC5, e_sensor_pin=PA1, stepper_spi_mosi_pin=PB15, stepper_spi_miso_pin=PB14, stepper_spi_sclk_pin=PB13, # accel diff --git a/boards/btt-manta-m8p-11/config.cfg b/boards/btt-manta-m8p-11/config.cfg index fc8e25c4..2e4b6df9 100644 --- a/boards/btt-manta-m8p-11/config.cfg +++ b/boards/btt-manta-m8p-11/config.cfg @@ -10,9 +10,9 @@ aliases: # steppers x_step_pin=PE2, x_dir_pin=PB4, x_enable_pin=PC11, x_uart_pin=PC10, x_diag_pin=PF3, x_endstop_pin=PF3, y_step_pin=PF12, y_dir_pin=PF11, y_enable_pin=PB3, y_uart_pin=PF13, y_diag_pin=PF4, y_endstop_pin=PF4, - z0_step_pin=PA10, z0_dir_pin=PA14, z0_enable_pin=PA15, z0_uart_pin=PF8, z0_diag_pin=null, - z1_step_pin=PD11, z1_dir_pin=PD9, z1_enable_pin=PD15, z1_uart_pin=PD14, z1_diag_pin=null, - z2_step_pin=PD8, z2_dir_pin=PC6, z2_enable_pin=PC7, z2_uart_pin=PD10, z2_diag_pin=null, + z0_step_pin=PA10, z0_dir_pin=PA14, z0_enable_pin=PA15, z0_uart_pin=PF8, z0_diag_pin=null, z_endstop_pin=PF5, + z1_step_pin=PD11, z1_dir_pin=PD9, z1_enable_pin=PD15, z1_uart_pin=PD14, z1_diag_pin=null, + z2_step_pin=PD8, z2_dir_pin=PC6, z2_enable_pin=PC7, z2_uart_pin=PD10, z2_diag_pin=null, # Voron 2.4 support on motor 5 z3_step_pin=PC9, z3_dir_pin=PC8, z3_enable_pin=PD1, z3_uart_pin=PD0, z3_diag_pin=null, e_step_pin=PD7, e_dir_pin=PD6, e_enable_pin=PF10, e_uart_pin=PF9, e_diag_pin=null, e_heater_pin=PE3, e_sensor_pin=PA1, @@ -22,6 +22,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB2, bltouch_control_pin=PB1, probe_pin=PB2, +# VAOC pins + vaoc_probe_pin=PC2 + vaoc_neopixel_pin=PC6 + vaoc_fan_pin=PE5 # fan 3 # 2 pin fans fan_part_cooling_pin=PE6, fan_toolhead_cooling_pin=PE0, diff --git a/boards/btt-manta-m8p-20/board-definition.json b/boards/btt-manta-m8p-20/board-definition.json index 1d1a4f73..20188fc2 100644 --- a/boards/btt-manta-m8p-20/board-definition.json +++ b/boards/btt-manta-m8p-20/board-definition.json @@ -34,9 +34,9 @@ "cs_pin": "PC13", "diag_pin": "PF4", "endstop_pin": "PF4", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR2": { "title": "MOTOR 2", @@ -47,9 +47,9 @@ "cs_pin": "PE3", "diag_pin": "PF3", "endstop_pin": "PF3", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR3": { "title": "MOTOR 3", @@ -60,9 +60,9 @@ "cs_pin": "PB9", "diag_pin": "PF2", "endstop_pin": "PF2", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR4": { "title": "MOTOR 4", @@ -73,9 +73,9 @@ "cs_pin": "PB5", "diag_pin": "PF1", "endstop_pin": "PF1", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR5": { "title": "MOTOR 5", @@ -86,9 +86,9 @@ "cs_pin": "PG14", "diag_pin": "PF0", "endstop_pin": "PF0", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR6": { "title": "MOTOR 6", @@ -99,9 +99,9 @@ "cs_pin": "PG10", "diag_pin": "PC15", "endstop_pin": "PC15", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR7": { "title": "MOTOR 7", @@ -110,9 +110,9 @@ "dir_pin": "PD3", "uart_pin": "PD5", "cs_pin": "PD5", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" }, "MOTOR8": { "title": "MOTOR 8", @@ -121,9 +121,9 @@ "dir_pin": "PC8", "uart_pin": "PC6", "cs_pin": "PC6", - "spi_software_mosi_pin": "PC12", - "spi_software_miso_pin": "PC11", - "spi_software_sclk_pin": "PC10" + "spi_software_mosi_pin": "PG6", + "spi_software_miso_pin": "PG7", + "spi_software_sclk_pin": "PG8" } }, "ADXL345SPI": { @@ -136,9 +136,9 @@ }, "stepperSPI": { "software": { - "sclk": "PC10", - "mosi": "PC12", - "miso": "PC11" + "sclk": "PG8", + "mosi": "PG6", + "miso": "PG7" } } } diff --git a/boards/btt-manta-m8p-20/config.cfg b/boards/btt-manta-m8p-20/config.cfg index 6e894bc2..3b336aac 100644 --- a/boards/btt-manta-m8p-20/config.cfg +++ b/boards/btt-manta-m8p-20/config.cfg @@ -8,11 +8,11 @@ [board_pins manta_m8p_tmc2209] aliases: # steppers - x_step_pin=PE6, x_dir_pin=PE5, x_enable_pin=PC14, x_uart_pin=PC13, x_diag_pin=PF4, x_endstop_pin=PF4, + x_step_pin=PE6, x_dir_pin=PE5, x_enable_pin=PC14, x_uart_pin=PC13, x_diag_pin=PF4, x_endstop_pin=PF4, y_step_pin=PE2, y_dir_pin=PE1, y_enable_pin=PE4, y_uart_pin=PE3, y_diag_pin=PF3, y_endstop_pin=PF3, - z0_step_pin=PG9, z0_dir_pin=PD7, z0_enable_pin=PG11, z0_uart_pin=PG10, z0_diag_pin=null, - z1_step_pin=PD4, z1_dir_pin=PD3, z1_enable_pin=PD6, z1_uart_pin=PD5, z1_diag_pin=null, - z2_step_pin=PC7, z2_dir_pin=PC8, z2_enable_pin=PD2, z2_uart_pin=PC6, z2_diag_pin=null, + z0_step_pin=PG9, z0_dir_pin=PD7, z0_enable_pin=PG11, z0_uart_pin=PG10, z0_diag_pin=null, z_endstop_pin=PC15, + z1_step_pin=PD4, z1_dir_pin=PD3, z1_enable_pin=PD6, z1_uart_pin=PD5, z1_diag_pin=null, + z2_step_pin=PC7, z2_dir_pin=PC8, z2_enable_pin=PD2, z2_uart_pin=PC6, z2_diag_pin=null, # Voron 2.4 support z3_step_pin=PG13, z3_dir_pin=PG12, z3_enable_pin=PG15, z3_uart_pin=PG14, z3_diag_pin=null, e_step_pin=PB8, e_dir_pin=PB7, e_enable_pin=PE0, e_uart_pin=PB9, e_diag_pin=null, e_heater_pin=PA0, e_sensor_pin=PB0, @@ -22,6 +22,10 @@ aliases: # auto leveling bltouch_sensor_pin=PD13, bltouch_control_pin=PD12, probe_pin=PD13, +# VAOC pins + vaoc_probe_pin=PF2 + vaoc_neopixel_pin=PD15 + vaoc_fan_pin=PF8 # fan 3 # 2 pin fans fan_part_cooling_pin=PF7, fan_toolhead_cooling_pin=PF9, @@ -31,8 +35,8 @@ aliases: 4p_fan_part_cooling_tach_pin=PC2, 4p_toolhead_cooling_pin=PA2, 4p_toolhead_cooling_tach_pin=PC1, - 4p_controller_board_pin=PA2, - 4p_controller_board_tach_pin=PC1, + 4p_controller_board_pin=PA4, + 4p_controller_board_tach_pin=VF4, # Bed heater heater_bed_heating_pin=PF5, heater_bed_sensor_pin=PB1, diff --git a/boards/btt-manta-m8p/config.cfg b/boards/btt-manta-m8p/config.cfg index 38f4ea1e..cb662cdb 100644 --- a/boards/btt-manta-m8p/config.cfg +++ b/boards/btt-manta-m8p/config.cfg @@ -10,10 +10,10 @@ aliases: # steppers x_step_pin=PE2, x_dir_pin=PB4, x_enable_pin=PC11, x_uart_pin=PC10, x_diag_pin=PF3, x_endstop_pin=PF3, y_step_pin=PF12, y_dir_pin=PF11, y_enable_pin=PB3, y_uart_pin=PF13, y_diag_pin=PF4, y_endstop_pin=PF4, - z0_step_pin=PA10, z0_dir_pin=PD15, z0_enable_pin=PA15, z0_uart_pin=PF8, z0_diag_pin=null, + z0_step_pin=PA10, z0_dir_pin=PD15, z0_enable_pin=PA15, z0_uart_pin=PF8, z0_diag_pin=null, z_endstop_pin=PC2, z1_step_pin=PD12, z1_dir_pin=PD11, z1_enable_pin=PD14, z1_uart_pin=PD13, z1_diag_pin=null, z2_step_pin=PD10, z2_dir_pin=PD8, z2_enable_pin=PD9, z2_uart_pin=PC7, z2_diag_pin=null, - z3_step_pin=PC9, z3_dir_pin=PC8, z3_enable_pin=PD1, z3_uart_pin=PD0, z3_diag_pin=null, # Voron 2.4 support on motor 5 + z3_step_pin=PC9, z3_dir_pin=PC8, z3_enable_pin=PD1, z3_uart_pin=PD0, z3_diag_pin=null, # Voron 2.4 support on motor 5 e_step_pin=PD7, e_dir_pin=PD6, e_enable_pin=PF10, e_uart_pin=PF9, e_diag_pin=null, e_heater_pin=PE3, e_sensor_pin=PA1, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # accel @@ -21,6 +21,9 @@ aliases: # auto leveling bltouch_sensor_pin=PB2, bltouch_control_pin=PB1, probe_pin=PB2, +# VAOC probe and neopixel + vaoc_probe_pin=PF5 + vaoc_neopixel_pin=PC6 # 2 pin fans fan_part_cooling_pin=PE6, fan_toolhead_cooling_pin=PE0, diff --git a/boards/btt-octopus-11-407/config.cfg b/boards/btt-octopus-11-407/config.cfg index a5e8c06e..23bb9060 100644 --- a/boards/btt-octopus-11-407/config.cfg +++ b/boards/btt-octopus-11-407/config.cfg @@ -8,19 +8,23 @@ [board_pins octopus_11_407_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # accel adxl345_cs_pin=PA15, # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-octopus-11/board-definition.json b/boards/btt-octopus-11/board-definition.json index 9fe615d4..76ec6407 100644 --- a/boards/btt-octopus-11/board-definition.json +++ b/boards/btt-octopus-11/board-definition.json @@ -3,7 +3,7 @@ "boardImageFileName": "board.webp", "manualFileName": "manual.pdf", "wireDiagramFileName": "wiring.drawio.svg", - "name": "Octopus V1.1 F446", + "name": "Octopus V1.1", "manufacturer": "BIGTREETECH", "id": "btt-octopus-11", "firmwareBinaryName": "firmware-btt-octopus-11.bin", diff --git a/boards/btt-octopus-11/config.cfg b/boards/btt-octopus-11/config.cfg index 0df55b9b..3b3e54a5 100644 --- a/boards/btt-octopus-11/config.cfg +++ b/boards/btt-octopus-11/config.cfg @@ -8,13 +8,13 @@ [board_pins octopus_11_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG10, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, # Hybrid CoreXY Single Toolhead y1_step_pin=PG4, y1_dir_pin=PC1, y1_enable_pin=PA0, y1_uart_pin=PC7, y1_diag_pin=PG11, x1_step_pin=PF9, x1_dir_pin=PF10, x1_enable_pin=PG2, x1_uart_pin=PF2, x1_diag_pin=PG12, @@ -28,6 +28,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-octopus-max-ez/config.cfg b/boards/btt-octopus-max-ez/config.cfg index cfe9b415..d1b4f5d8 100644 --- a/boards/btt-octopus-max-ez/config.cfg +++ b/boards/btt-octopus-max-ez/config.cfg @@ -10,7 +10,7 @@ aliases: # steppers (Motor 1-7: X, Y, E, Z3, Z0, Z1, Z2, Motor 8-10: unused) x_step_pin=PC13, x_dir_pin=PC14, x_enable_pin=PE6, x_uart_pin=PG14, x_diag_pin=PF0, x_endstop_pin=PF0, y_step_pin=PE4, y_dir_pin=PE5, y_enable_pin=PE3, y_uart_pin=PG13, y_diag_pin=PF2, y_endstop_pin=PF2, - z0_step_pin=PB5, z0_dir_pin=PB4, z0_enable_pin=PB6, z0_uart_pin=PG10, z0_diag_pin=null, z_endstop_pin=PF4, + z0_step_pin=PB5, z0_dir_pin=PB4, z0_enable_pin=PB6, z0_uart_pin=PG10, z0_diag_pin=null, z_endstop_pin=PC15, z1_step_pin=PG15, z1_dir_pin=PB3, z1_enable_pin=PD5, z1_uart_pin=PG9, z1_diag_pin=null, z2_step_pin=PD3, z2_dir_pin=PD2, z2_enable_pin=PD4, z2_uart_pin=PD7, z2_diag_pin=null, z3_step_pin=PB8, z3_dir_pin=PB9, z3_enable_pin=PB7, z3_uart_pin=PG11, z3_diag_pin=null, # Voron 2.4 support @@ -23,6 +23,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB15, bltouch_control_pin=PB14, probe_pin=PB15, +# VAOC pins + vaoc_probe_pin=PF4 + vaoc_neopixel_pin=PE10 + vaoc_fan_pin=PA3 # fan 3 # 2p fans fan_part_cooling_pin=PA6, fan_toolhead_cooling_pin=PA5, diff --git a/boards/btt-octopus-pro-429/config.cfg b/boards/btt-octopus-pro-429/config.cfg index 3728b6a3..a44218be 100644 --- a/boards/btt-octopus-pro-429/config.cfg +++ b/boards/btt-octopus-pro-429/config.cfg @@ -8,13 +8,13 @@ [board_pins octopus_pro_429_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # Hybrid CoreXY Single Toolhead y1_step_pin=PG4, y1_dir_pin=PC1, y1_enable_pin=PA0, y1_uart_pin=PC7, y1_diag_pin=PG11, @@ -27,6 +27,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-octopus-pro-446/config.cfg b/boards/btt-octopus-pro-446/config.cfg index d224d943..ef85ea74 100644 --- a/boards/btt-octopus-pro-446/config.cfg +++ b/boards/btt-octopus-pro-446/config.cfg @@ -8,13 +8,13 @@ [board_pins octopus_pro_446_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # Hybrid CoreXY Single Toolhead y1_step_pin=PG4, y1_dir_pin=PC1, y1_enable_pin=PA0, y1_uart_pin=PC7, y1_diag_pin=PG11, @@ -27,6 +27,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-octopus-pro-h723-11/config.cfg b/boards/btt-octopus-pro-h723-11/config.cfg index 3fb3d914..16cb9ced 100644 --- a/boards/btt-octopus-pro-h723-11/config.cfg +++ b/boards/btt-octopus-pro-h723-11/config.cfg @@ -8,13 +8,13 @@ [board_pins octopus_pro_h723_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA0, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA0, e_sensor_pin=PF4, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # Hybrid CoreXY Single Toolhead y1_step_pin=PG4, y1_dir_pin=PC1, y1_enable_pin=PA2, y1_uart_pin=PC7, y1_diag_pin=PG11, @@ -27,6 +27,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-octopus-pro-h723/config.cfg b/boards/btt-octopus-pro-h723/config.cfg index edd96e5e..ce28c126 100644 --- a/boards/btt-octopus-pro-h723/config.cfg +++ b/boards/btt-octopus-pro-h723/config.cfg @@ -8,13 +8,13 @@ [board_pins octopus_pro_h723_tmc2209] aliases: # steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, + x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, + y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, + z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, z_endstop_pin=PG15, z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, + z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, + z3_step_pin=PF9, z3_dir_pin=PF10, z3_enable_pin=PG2, z3_uart_pin=PF2, z3_diag_pin=null, # Voron 2.4 support + e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, stepper_spi_mosi_pin=PA7, stepper_spi_miso_pin=PA6, stepper_spi_sclk_pin=PA5, # Hybrid CoreXY Single Toolhead y1_step_pin=PG4, y1_dir_pin=PC1, y1_enable_pin=PA0, y1_uart_pin=PC7, y1_diag_pin=PG11, @@ -27,6 +27,10 @@ aliases: # auto leveling bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, probe_pin=PB7, +# VAOC pins + vaoc_probe_pin=PG10 + vaoc_neopixel_pin=PB0 + vaoc_fan_pin=PD13 # fan 3 # fans fan_part_cooling_pin=PA8, fan_toolhead_cooling_pin=PE5, diff --git a/boards/btt-sb-2240-10-stm32/toolboard-config.cfg b/boards/btt-sb-2240-10-stm32/toolboard-config.cfg index 8ad68ad3..096629f4 100644 --- a/boards/btt-sb-2240-10-stm32/toolboard-config.cfg +++ b/boards/btt-sb-2240-10-stm32/toolboard-config.cfg @@ -28,6 +28,6 @@ serial: /dev/btt-sb2240-10-stm [adxl345 toolboard] cs_pin: toolboard:adxl345_cs_pin -spi_software_sclk_pin: toolboard:PB10 -spi_software_mosi_pin: toolboard:PB11 -spi_software_miso_pin: toolboard:PB2 \ No newline at end of file +spi_software_sclk_pin: toolboard: PB10 +spi_software_mosi_pin: toolboard: PB11 +spi_software_miso_pin: toolboard: PB2 \ No newline at end of file diff --git a/boards/btt-skr-14-turbo/config.cfg b/boards/btt-skr-14-turbo/config.cfg index 72bd08ca..05279603 100644 --- a/boards/btt-skr-14-turbo/config.cfg +++ b/boards/btt-skr-14-turbo/config.cfg @@ -8,12 +8,12 @@ [board_pins skr_14_turbo_tmc2209] aliases: # steppers - x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29, - y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28, - z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null, - z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, - z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, - e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24, + x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29, + y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28, + z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null, z_endstop_pin=P1.27, + z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, + z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, + e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24, # accel adxl345_cs_pin=null, # auto leveling diff --git a/boards/btt-skr-14/config.cfg b/boards/btt-skr-14/config.cfg index 9e02f2d1..f1138aa8 100644 --- a/boards/btt-skr-14/config.cfg +++ b/boards/btt-skr-14/config.cfg @@ -8,12 +8,12 @@ [board_pins skr_14_tmc2209] aliases: # steppers - x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29, - y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28, - z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null, - z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, - z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, - e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24, + x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29, + y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28, + z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null, z_endstop_pin=P1.27, + z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, + z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, + e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24, # accel adxl345_cs_pin=null, # auto leveling diff --git a/boards/btt-skr-2-407/config.cfg b/boards/btt-skr-2-407/config.cfg index 2e0a6d26..58b90275 100644 --- a/boards/btt-skr-2-407/config.cfg +++ b/boards/btt-skr-2-407/config.cfg @@ -8,9 +8,9 @@ [board_pins skr_2_407_tmc2209] aliases: # steppers - x_step_pin=PE2, x_dir_pin=PE1, x_enable_pin=PE3, x_uart_pin=PE0, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PD5, y_dir_pin=PD4, y_enable_pin=PD6, y_uart_pin=PD3, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PA15, z0_dir_pin=PA8, z0_enable_pin=PD1, z0_uart_pin=PD0, z0_diag_pin=PC0, z_endstop_pin=PC0, + x_step_pin=PE2, x_dir_pin=PE1, x_enable_pin=PE3, x_uart_pin=PE0, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PD5, y_dir_pin=PD4, y_enable_pin=PD6, y_uart_pin=PD3, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PA15, z0_dir_pin=PA8, z0_enable_pin=PD1, z0_uart_pin=PD0, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-2-429/config.cfg b/boards/btt-skr-2-429/config.cfg index 36d062a1..bad884bf 100644 --- a/boards/btt-skr-2-429/config.cfg +++ b/boards/btt-skr-2-429/config.cfg @@ -8,9 +8,9 @@ [board_pins skr_2_429_tmc2209] aliases: # steppers - x_step_pin=PE2, x_dir_pin=PE1, x_enable_pin=PE3, x_uart_pin=PE0, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PD5, y_dir_pin=PD4, y_enable_pin=PD6, y_uart_pin=PD3, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PA15, z0_dir_pin=PA8, z0_enable_pin=PD1, z0_uart_pin=PD0, z0_diag_pin=PC0, z_endstop_pin=PC0, + x_step_pin=PE2, x_dir_pin=PE1, x_enable_pin=PE3, x_uart_pin=PE0, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PD5, y_dir_pin=PD4, y_enable_pin=PD6, y_uart_pin=PD3, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PA15, z0_dir_pin=PA8, z0_enable_pin=PD1, z0_uart_pin=PD0, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-3-ez-h723/config.cfg b/boards/btt-skr-3-ez-h723/config.cfg index d2287e2b..a9bf71d9 100644 --- a/boards/btt-skr-3-ez-h723/config.cfg +++ b/boards/btt-skr-3-ez-h723/config.cfg @@ -8,9 +8,9 @@ [board_pins btt_skr_3_ez_h723_tmc2209] aliases: # steppers - x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-3-ez/config.cfg b/boards/btt-skr-3-ez/config.cfg index e43cbdd9..c389ccc3 100644 --- a/boards/btt-skr-3-ez/config.cfg +++ b/boards/btt-skr-3-ez/config.cfg @@ -8,9 +8,9 @@ [board_pins btt_skr_3_tmc2209] aliases: # steppers - x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-3-h723/config-3z.cfg b/boards/btt-skr-3-h723/config-3z.cfg new file mode 100644 index 00000000..df4b9066 --- /dev/null +++ b/boards/btt-skr-3-h723/config-3z.cfg @@ -0,0 +1,47 @@ +# WARNING. DO NOT EDIT THIS FILE. +# To override settings from this file, you can copy and paste the relevant +# sections into your printer.cfg and change it there. + +[board_pins btt_skr_3_tmc2209] +aliases: +# steppers + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + z1_step_pin=PD15, z1_dir_pin=PD14, z1_enable_pin=PC7, z1_uart_pin=PC6, z1_diag_pin=PC2, + z2_step_pin=PD11, z2_dir_pin=PD10, z2_enable_pin=PD13, z2_uart_pin=PD12, z2_diag_pin=PA0, + e_step_pin=null, e_dir_pin=null, e_enable_pin=null, e_uart_pin=null, e_diag_pin=null, e_heater_pin=PB3, e_sensor_pin=PA2, +# accel + adxl345_cs_pin=PB12, adxl345_sclk=PB13, adxl345_mosi=PB15, adxl345_miso=PB14, +# auto leveling + bltouch_sensor_pin=PC13, bltouch_control_pin=PE5, + probe_pin=PC13, +# fans + fan_part_cooling_pin=PB7, + fan_toolhead_cooling_pin=PB6, + fan_controller_board_pin=PB5, +# Bed heater + heater_bed_heating_pin=PD7, + heater_bed_sensor_pin=PA1, + +## Expansion ports + # EXP1 header + EXP1_1=PC5, EXP1_3=PB1, EXP1_5=PE9, EXP1_7=PE11, EXP1_9=, + EXP1_2=PB0, EXP1_4=PE8, EXP1_6=PE10, EXP1_8=PE12, EXP1_10=<5V>, + # EXP2 header + EXP2_1=PA6, EXP2_3=PE7, EXP2_5=PB2, EXP2_7=PC4, EXP2_9=, + EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=, EXP2_10=, + # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2" + +[mcu] +serial: /dev/btt-skr-3-ez + +# still not supported on the stm32f743 +#[temperature_sensor SKR_3] +#sensor_type: temperature_mcu +#min_temp: 0 +#max_temp: 100 + +[adxl345] +spi_bus: spi2 # Wifi slot SPI pins. +cs_pin: adxl345_cs_pin diff --git a/boards/btt-skr-3-h723/config.cfg b/boards/btt-skr-3-h723/config.cfg index 979ff032..ce6ec03b 100644 --- a/boards/btt-skr-3-h723/config.cfg +++ b/boards/btt-skr-3-h723/config.cfg @@ -8,9 +8,9 @@ [board_pins btt_skr_3_tmc2209] aliases: # steppers - x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-3/config-3z.cfg b/boards/btt-skr-3/config-3z.cfg new file mode 100644 index 00000000..df4b9066 --- /dev/null +++ b/boards/btt-skr-3/config-3z.cfg @@ -0,0 +1,47 @@ +# WARNING. DO NOT EDIT THIS FILE. +# To override settings from this file, you can copy and paste the relevant +# sections into your printer.cfg and change it there. + +[board_pins btt_skr_3_tmc2209] +aliases: +# steppers + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + z1_step_pin=PD15, z1_dir_pin=PD14, z1_enable_pin=PC7, z1_uart_pin=PC6, z1_diag_pin=PC2, + z2_step_pin=PD11, z2_dir_pin=PD10, z2_enable_pin=PD13, z2_uart_pin=PD12, z2_diag_pin=PA0, + e_step_pin=null, e_dir_pin=null, e_enable_pin=null, e_uart_pin=null, e_diag_pin=null, e_heater_pin=PB3, e_sensor_pin=PA2, +# accel + adxl345_cs_pin=PB12, adxl345_sclk=PB13, adxl345_mosi=PB15, adxl345_miso=PB14, +# auto leveling + bltouch_sensor_pin=PC13, bltouch_control_pin=PE5, + probe_pin=PC13, +# fans + fan_part_cooling_pin=PB7, + fan_toolhead_cooling_pin=PB6, + fan_controller_board_pin=PB5, +# Bed heater + heater_bed_heating_pin=PD7, + heater_bed_sensor_pin=PA1, + +## Expansion ports + # EXP1 header + EXP1_1=PC5, EXP1_3=PB1, EXP1_5=PE9, EXP1_7=PE11, EXP1_9=, + EXP1_2=PB0, EXP1_4=PE8, EXP1_6=PE10, EXP1_8=PE12, EXP1_10=<5V>, + # EXP2 header + EXP2_1=PA6, EXP2_3=PE7, EXP2_5=PB2, EXP2_7=PC4, EXP2_9=, + EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=, EXP2_10=, + # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2" + +[mcu] +serial: /dev/btt-skr-3-ez + +# still not supported on the stm32f743 +#[temperature_sensor SKR_3] +#sensor_type: temperature_mcu +#min_temp: 0 +#max_temp: 100 + +[adxl345] +spi_bus: spi2 # Wifi slot SPI pins. +cs_pin: adxl345_cs_pin diff --git a/boards/btt-skr-3/config.cfg b/boards/btt-skr-3/config.cfg index 979ff032..ce6ec03b 100644 --- a/boards/btt-skr-3/config.cfg +++ b/boards/btt-skr-3/config.cfg @@ -8,9 +8,9 @@ [board_pins btt_skr_3_tmc2209] aliases: # steppers - x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, - y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, - z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, + x_step_pin=PD4, x_dir_pin=PD3, x_enable_pin=PD6, x_uart_pin=PD5, x_diag_pin=PC1, x_endstop_pin=PC1, + y_step_pin=PA15, y_dir_pin=PA8, y_enable_pin=PD1, y_uart_pin=PD0, y_diag_pin=PC3, y_endstop_pin=PC3, + z0_step_pin=PE2, z0_dir_pin=PE3, z0_enable_pin=PE0, z0_uart_pin=PE1, z0_diag_pin=PC0, z_endstop_pin=PC0, z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null, z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, e_step_pin=PD11, e_dir_pin=PD10, e_enable_pin=PD13, e_uart_pin=PD12, e_diag_pin=PA0, e_heater_pin=PB3, e_sensor_pin=PA2, diff --git a/boards/btt-skr-pro-12/config.cfg b/boards/btt-skr-pro-12/config.cfg index 95769415..0656fdb7 100644 --- a/boards/btt-skr-pro-12/config.cfg +++ b/boards/btt-skr-pro-12/config.cfg @@ -8,9 +8,9 @@ [board_pins skr_12_pro_tmc2209] aliases: # steppers - x_step_pin=PE9, x_dir_pin=PF1, x_enable_pin=PF2, x_uart_pin=PC13, x_diag_pin=PB10, x_endstop_pin=PB10, + x_step_pin=PE9, x_dir_pin=PF1, x_enable_pin=PF2, x_uart_pin=PC13, x_diag_pin=PB10, x_endstop_pin=PB10, y_step_pin=PE11, y_dir_pin=PE8, y_enable_pin=PD7, y_uart_pin=PE3, y_diag_pin=PE12, y_endstop_pin=PE12, - z0_step_pin=PE14, z0_dir_pin=PA0, z0_enable_pin=PC3, z0_uart_pin=PD4, z0_diag_pin=null, + z0_step_pin=PE14, z0_dir_pin=PA0, z0_enable_pin=PC3, z0_uart_pin=PD4, z0_diag_pin=null, z_endstop_pin=PG8, z1_step_pin=PD15, z1_dir_pin=PE7, z1_enable_pin=PA3, z1_uart_pin=PD1, z1_diag_pin=null, z2_step_pin=PD13, z2_dir_pin=PG9, z2_enable_pin=PF0, z2_uart_pin=PD6, z2_diag_pin=null, e_step_pin=PE13, e_dir_pin=PC2, e_enable_pin=PC0, e_uart_pin=PE1, e_diag_pin=null, e_heater_pin=PB1, e_sensor_pin=PF4, diff --git a/boards/btt-skrat-10/config.cfg b/boards/btt-skrat-10/config.cfg index aa514a3f..76ebad91 100644 --- a/boards/btt-skrat-10/config.cfg +++ b/boards/btt-skrat-10/config.cfg @@ -8,12 +8,12 @@ [board_pins btt_skrat_10] aliases: # steppers - x_step_pin=PF9, x_dir_pin=PD7, x_enable_pin=PD6, x_uart_pin=PF10, x_diag_pin=PB5, x_endstop_pin=PB5, - y_step_pin=PD3, y_dir_pin=PD2, y_enable_pin=PD5, y_uart_pin=PD4, y_diag_pin=PC1, y_endstop_pin=PC1, - z0_step_pin=PA15, z0_dir_pin=PF8, z0_enable_pin=PC9, z0_uart_pin=PC8, z0_diag_pin=PC0, z_endstop_pin=PC0, - z1_step_pin=PC7, z1_dir_pin=PC6, z1_enable_pin=PD9, z1_uart_pin=PD8, z1_diag_pin=PF4, - z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, - e_step_pin=PB10, e_dir_pin=PE15, e_enable_pin=PA8, e_uart_pin=PB11, e_diag_pin=PF5, e_endstop_pin=PF5, + x_step_pin=PF9, x_dir_pin=PD7, x_enable_pin=PD6, x_uart_pin=PF10, x_diag_pin=PB5, x_endstop_pin=PB5, + y_step_pin=PD3, y_dir_pin=PD2, y_enable_pin=PD5, y_uart_pin=PD4, y_diag_pin=PC1, y_endstop_pin=PC1, + z0_step_pin=PA15, z0_dir_pin=PF8, z0_enable_pin=PC9, z0_uart_pin=PC8, z0_diag_pin=PC0, z_endstop_pin=PC0, + z1_step_pin=PC7, z1_dir_pin=PC6, z1_enable_pin=PD9, z1_uart_pin=PD8, z1_diag_pin=PF4, + z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null, + e_step_pin=PB10, e_dir_pin=PE15, e_enable_pin=PA8, e_uart_pin=PB11, e_diag_pin=PF5, e_endstop_pin=PF5, # Extrusion e_heater_pin=PE11, e_sensor_pin=PA3, # accel @@ -37,9 +37,12 @@ aliases: heater_bed_sensor_pin=PB2 ## Expansion ports - # EXP1 header - # EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=, - # EXP1_2=PA15, EXP1_4=, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>, + # EXP1 header + #EXP1_1=PC13, EXP1_3=PC3, EXP1_5=PB1, EXP1_7=PC5, EXP1_9=, + #EXP1_2=PF3, EXP1_4=PC2, EXP1_6=PB0, EXP1_8=PC4, EXP1_10=<5V>, + # EXP2 header + #EXP2_1=PA6, EXP2_3=PE7, EXP2_5=PE8, EXP2_7=PE10, EXP2_9=, + #EXP2_2=PA5, EXP2_4=PF7, EXP2_6=PA7, EXP2_8=, EXP2_10= [temperature_sensor SKRat] sensor_type: temperature_mcu diff --git a/boards/fysetc-spider-22/config.cfg b/boards/fysetc-spider-22/config.cfg index 730e2305..d441f8cd 100644 --- a/boards/fysetc-spider-22/config.cfg +++ b/boards/fysetc-spider-22/config.cfg @@ -10,7 +10,7 @@ aliases: # steppers x_step_pin=PE11, x_dir_pin=PE10, x_enable_pin=PE9, x_uart_pin=PE7, x_diag_pin=PB14, x_endstop_pin=PB14, y_step_pin=PD8, y_dir_pin=PB12, y_enable_pin=PD9, y_uart_pin=PE15, y_diag_pin=PB13, y_endstop_pin=PB13, - z0_step_pin=PE1, z0_dir_pin=PE0, z0_enable_pin=PC5, z0_uart_pin=PD11, z0_diag_pin=PA0, z0_endstop_pin=PA0, + z0_step_pin=PE1, z0_dir_pin=PE0, z0_enable_pin=PC5, z0_uart_pin=PD11, z0_diag_pin=PA0, z0_endstop_pin=PA3, z1_step_pin=PD12, z1_dir_pin=PC4, z1_enable_pin=PE8, z1_uart_pin=PA15, z1_diag_pin=null, z2_step_pin=PE2, z2_dir_pin=PE4, z2_enable_pin=PE3, z2_uart_pin=PC15, z2_diag_pin=null, z3_step_pin=PE6, z3_dir_pin=PC13, z3_enable_pin=PE5, z3_uart_pin=PC14, z3_diag_pin=null, # Voron 2.4 support @@ -20,6 +20,10 @@ aliases: # auto leveling bltouch_sensor_pin=PA0, bltouch_control_pin=PA2, probe_pin=PA0, +# VAOC pins + vaoc_probe_pin=PA0 # Z+ + vaoc_neopixel_pin=PD3 + vaoc_fan_pin=PB3 # E2 Out # fans fan_part_cooling_pin=PA13, fan_toolhead_cooling_pin=PA14, diff --git a/boards/fysetc-spider/config.cfg b/boards/fysetc-spider/config.cfg index adae9232..63a72e17 100644 --- a/boards/fysetc-spider/config.cfg +++ b/boards/fysetc-spider/config.cfg @@ -8,17 +8,21 @@ [board_pins fysetc_spider_tmc2209] aliases: # steppers - x_step_pin=PE11, x_dir_pin=PE10, x_enable_pin=PE9, x_uart_pin=PE7, x_diag_pin=null, x_endstop_pin=PB14, # top-left stepper - y_step_pin=PD8, y_dir_pin=PB12, y_enable_pin=PD9, y_uart_pin=PE15, y_diag_pin=null, y_endstop_pin=PB13, # top-right stepper - z0_step_pin=PE1, z0_dir_pin=PE0, z0_enable_pin=PC5, z0_uart_pin=PD11, z0_diag_pin=null, # front-left stepper - z1_step_pin=PD12, z1_dir_pin=PC4, z1_enable_pin=PE8, z1_uart_pin=PA15, z1_diag_pin=null, # middle-back stepper - z2_step_pin=PE2, z2_dir_pin=PE4, z2_enable_pin=PE3, z2_uart_pin=PC15, z2_diag_pin=null, # front-right stepper - e_step_pin=PD5, e_dir_pin=PD6, e_enable_pin=PD4, e_uart_pin=PD7, e_diag_pin=null, e_heater_pin=PB15, e_sensor_pin=PC0, + x_step_pin=PE11, x_dir_pin=PE10, x_enable_pin=PE9, x_uart_pin=PE7, x_diag_pin=null, x_endstop_pin=PB14, # top-left stepper + y_step_pin=PD8, y_dir_pin=PB12, y_enable_pin=PD9, y_uart_pin=PE15, y_diag_pin=null, y_endstop_pin=PB13, # top-right stepper + z0_step_pin=PE1, z0_dir_pin=PE0, z0_enable_pin=PC5, z0_uart_pin=PD11, z0_diag_pin=null, z_endstop_pin=PA3, # front-left stepper + z1_step_pin=PD12, z1_dir_pin=PC4, z1_enable_pin=PE8, z1_uart_pin=PA15, z1_diag_pin=null, # middle-back stepper + z2_step_pin=PE2, z2_dir_pin=PE4, z2_enable_pin=PE3, z2_uart_pin=PC15, z2_diag_pin=null, # front-right stepper + e_step_pin=PD5, e_dir_pin=PD6, e_enable_pin=PD4, e_uart_pin=PD7, e_diag_pin=null, e_heater_pin=PB15, e_sensor_pin=PC0, # accel adxl345_cs_pin=PA4, # auto leveling bltouch_sensor_pin=PA0, bltouch_control_pin=PA2, probe_pin=PA3, +# VAOC pins + vaoc_probe_pin=PA0 + vaoc_neopixel_pin=PD3 + vaoc_fan_pin=PB3 # E2 Out # fans fan_part_cooling_pin=PB1, fan_toolhead_cooling_pin=PB0, diff --git a/boards/ldo-leviathan-12/config.cfg b/boards/ldo-leviathan-12/config.cfg index f049592e..839b69f8 100644 --- a/boards/ldo-leviathan-12/config.cfg +++ b/boards/ldo-leviathan-12/config.cfg @@ -13,13 +13,17 @@ aliases: z0_step_pin=PD4, z0_dir_pin=PD3, z0_enable_pin=PD7, z0_uart_pin=PD5, z0_diag_pin=PD6, z_endstop_pin=PC3, z1_step_pin=PC12, z1_dir_pin=PC11, z1_enable_pin=PD2, z1_uart_pin=PD0, z1_diag_pin=PD1, z2_step_pin=PC9, z2_dir_pin=PC8, z2_enable_pin=PC10, z2_uart_pin=PA8, z2_diag_pin=PA15, - z3_step_pin=PG7, z3_dir_pin=PG6, z3_enable_pin=PC7, z3_uart_pin=PG8, z3_diag_pin=PC6, # Voron 2.4 support + z3_step_pin=PG7, z3_dir_pin=PG6, z3_enable_pin=PC7, z3_uart_pin=PG8, z3_diag_pin=PC6, # Voron 2.4 support e_step_pin=PD10, e_dir_pin=PD9, e_enable_pin=PD13, e_uart_pin=PD11, e_diag_pin=null, e_heater_pin=PG10, e_sensor_pin=PA2, # accel adxl345_cs_pin=PB12, # auto leveling bltouch_sensor_pin=null, bltouch_control_pin=null, probe_pin=PF1, +# VAOC pins + vaoc_probe_pin=PF1 # z-probe + vaoc_neopixel_pin=PF10 + vaoc_fan_pin=PF9 # fan 3 # fans fan_part_cooling_pin=PB7, fan_part_cooling_tach_pin=PB8, diff --git a/boards/ldo-orbitool-o2/board-definition.json b/boards/ldo-orbitool-o2/board-definition.json index 394bdce7..70486908 100644 --- a/boards/ldo-orbitool-o2/board-definition.json +++ b/boards/ldo-orbitool-o2/board-definition.json @@ -7,13 +7,19 @@ "firmwareBinaryName": "firmware-ldo-orbitool-o2.bin", "boardImageFileName": "board.webp", "compileScript": "compile.sh", - "thermistorPullup": 2200, "flashScript": "flash.sh", "documentationLink": "https://os.ratrig.com/docs/boards/ldo/orbitool-o2", "disableAutoFlash": true, "driverVoltages": [24], "hasMcuTempSensor": true, - "invertPinLogic": ["PA9"], + "invertPinLogic": ["PA9", "PA4"], + "outputPins": [ + { + "name": "hotend_power", + "pin": "PA10", + "value": 0 + } + ], "driverCount": 1, "integratedDrivers": { "extruder": "LDO-TMC2209" @@ -32,8 +38,10 @@ }, "LIS2DW": { "cs_pin": "PA4", - "hardware": { - "bus": "spi1" + "software": { + "sclk": "PA5", + "mosi": "PA7", + "miso": "PA6" } }, "customSections": { @@ -57,21 +65,13 @@ } }, "heater_fan": { - "name": "toolhead_cooling_fan", + "name": "_toolhead_cooling_fan", "comments": ["Use max_power: 0.5 for 12V, max_power: 1 for 24V (in printer.cfg)"], "parameters": { "max_power": 0.995, "cycle_time": 0.0001 } }, - "output_pin": { - "name": "O2_RUN_LED", - "parameters": { - "pin": "PB8", - "shutdown_value": 0, - "value": 1 - } - }, "temperature_sensor": { "name": "hotend_power_draw", "parameters": { diff --git a/boards/ldo-orbitool-o2/toolboard-config.cfg b/boards/ldo-orbitool-o2/toolboard-config.cfg index f5efc33e..668aa890 100644 --- a/boards/ldo-orbitool-o2/toolboard-config.cfg +++ b/boards/ldo-orbitool-o2/toolboard-config.cfg @@ -16,7 +16,7 @@ aliases: # adxl345 cs pin (LIS2DW12 in the case of this board) adxl345_cs_pin=PA4 # fans - fan_part_cooling_pin=PA10, + fan_part_cooling_pin=PA1, fan_toolhead_cooling_pin=PA9 # 4 pin fans 4p_fan_toolhead_cooling_tach_pin=PA8, \ No newline at end of file diff --git a/boards/prusa-buddy/config.cfg b/boards/prusa-buddy/config.cfg index f924c77d..a855865b 100644 --- a/boards/prusa-buddy/config.cfg +++ b/boards/prusa-buddy/config.cfg @@ -8,10 +8,10 @@ [board_pins prusa_buddy] aliases: # steppers - x_step_pin=PD1, x_dir_pin=PD0, x_enable_pin=PD3, x_uart_pin=PD5, x_diag_pin=PE2, x_endstop_pin=PE2, - y_step_pin=PD13, y_dir_pin=PD12, y_enable_pin=PD14, y_uart_pin=PD5, y_diag_pin=PE1, y_endstop_pin=PE1, - z0_step_pin=PD4, z0_dir_pin=PD15, z0_enable_pin=PD2, z0_uart_pin=PD5, z0_diag_pin=PE3, - e_step_pin=PD9, e_dir_pin=PD8, e_enable_pin=PD10, e_uart_pin=PD5, e_diag_pin=PA15, e_heater_pin=PB1, e_sensor_pin=PC0, + x_step_pin=PD1, x_dir_pin=PD0, x_enable_pin=PD3, x_uart_pin=PD5, x_diag_pin=PE2, x_endstop_pin=PE2, + y_step_pin=PD13, y_dir_pin=PD12, y_enable_pin=PD14, y_uart_pin=PD5, y_diag_pin=PE1, y_endstop_pin=PE1, + z0_step_pin=PD4, z0_dir_pin=PD15, z0_enable_pin=PD2, z0_uart_pin=PD5, z0_diag_pin=PE3, z_endstop_pin=PE3, + e_step_pin=PD9, e_dir_pin=PD8, e_enable_pin=PD10, e_uart_pin=PD5, e_diag_pin=PA15, e_heater_pin=PB1, e_sensor_pin=PC0, # auto leveling probe_pin=PA8, # fans diff --git a/boards/prusa-einsy/config.cfg b/boards/prusa-einsy/config.cfg index ff223fc6..690c7dc7 100644 --- a/boards/prusa-einsy/config.cfg +++ b/boards/prusa-einsy/config.cfg @@ -9,10 +9,10 @@ [board_pins einsy_rambo_prusa_tmc2130] aliases: # steppers - x_step_pin=PC0, x_dir_pin=PL0, x_enable_pin=PA7, x_diag_pin=PK2, x_uart_pin=PG0, x_endstop_pin=PK2, - y_step_pin=PC1, y_dir_pin=PL1, y_enable_pin=PA6, y_diag_pin=PK7, y_uart_pin=PG2, y_endstop_pin=PK7 - z0_step_pin=PC2, z0_dir_pin=PL2, z0_enable_pin=PA5, z0_diag_pin=PK6, z0_uart_pin=PK5, - e_step_pin=PC3, e_dir_pin=PL6, e_enable_pin=PA4, e_diag_pin=PK3, e_uart_pin=PK4, e_heater_pin=PE5, e_sensor_pin=PF0, + x_step_pin=PC0, x_dir_pin=PL0, x_enable_pin=PA7, x_diag_pin=PK2, x_uart_pin=PG0, x_endstop_pin=PK2, + y_step_pin=PC1, y_dir_pin=PL1, y_enable_pin=PA6, y_diag_pin=PK7, y_uart_pin=PG2, y_endstop_pin=PK7, + z0_step_pin=PC2, z0_dir_pin=PL2, z0_enable_pin=PA5, z0_diag_pin=PK6, z0_uart_pin=PK5, + e_step_pin=PC3, e_dir_pin=PL6, e_enable_pin=PA4, e_diag_pin=PK3, e_uart_pin=PK4, e_heater_pin=PE5, e_sensor_pin=PF0, # auto leveling probe_pin=PB4, # fans