SuperSlicer_config_bundle.ini

# generated by SuperSlicer 2.5.60.0 on 2024-12-11 at 09:41:02 UTC

[print:Ellis-PIF Standard-11mm3s]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 85%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 120
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 100%
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 40%
fill_pattern = grid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.25
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 3
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = notconnected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 20
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 4
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 0
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Ellis - PIF Standard (11mm3/s)
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 3
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 33%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 450
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:Joshi Uboot]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 85%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 120
brim_ears_pattern = concentric
brim_inside_holes = 1
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 4
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 100%
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 100%
fill_pattern = rectilinear
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.3
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 3
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = connected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 35
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 4
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 0
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Tuned Standard
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 5
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 3
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 50%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:Standard]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 85%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 120
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 100%
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 40%
fill_pattern = gyroid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.25
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 3
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = connected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 35
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = 
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 4
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 0
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Standard
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 5
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 3
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 33%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:Standard Functional]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 87%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 1
brim_ears_detection_length = 1
brim_ears_max_angle = 120
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 5
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 97%
external_perimeter_extrusion_width = 
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 40%
fill_pattern = gyroid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.3
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 3
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = connected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 40
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = -----------------CHANGELOG--------------------\n2024-04-29 Baseline - removed lines thickness custom variable\n2024-06-13 4 Perimeters 5solid top+bottom layers 10%infill gyroid\n2024-12-04 upped minmal filament extrusion length in skirt before print to 40mm\nFlow ratio 85->87\nexternal Perimeter 100->102\nAdded Brim ears\ngood results\n\n
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 0
perimeter_extrusion_width = 
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 5
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 0\n
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Standard Functional
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 5
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 5
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = snug
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 33%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:Standard Functional MAIN]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 5
bottom_solid_min_thickness = 1
bridge_acceleration = 3000
bridge_angle = 0
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 87%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 1
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 10
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 97%
external_perimeter_extrusion_width = 
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 40%
fill_pattern = gyroid
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.25
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 3
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = notconnected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 40
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = -----------------CHANGELOG--------------------\n2024-04-29 Baseline - removed lines thickness custom variable\n2024-06-13 4 Perimeters 5solid top+bottom layers 10%infill gyroid\n2024-12-04 upped minmal filament extrusion length in skirt before print to 40mm\nFlow ratio 85->87\nexternal Perimeter 100->102\nAdded Brim ears\ngood results\n2024-12-11 took width and spacing for (external) perimeters from ellis profile\n   upped Brim to 10mm - just ears need a bit more?\n   reduced skirt min loops 5-> 2\n   set Bridges infill to not connected - accordign to ellis profile\n   \n\n\nshould check first layer squish to check if going to 0,25 first layer height makes sense\n\n\n\n\n\n\n
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 100%
perimeter_extrusion_width = 
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 5
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 0\n
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Standard Functional
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 5
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 2
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = snug
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 33%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 1
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[print:Tuned Standard]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
avoid_crossing_top = 1
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 3000
bridge_angle = 90
bridge_fill_pattern = rectilinear
bridge_flow_ratio = 85%
bridge_overlap = 50%
bridge_overlap_min = 50%
bridge_precision = 25%
bridge_speed = 140
bridge_type = nozzle
bridged_infill_margin = 300%
brim_acceleration = 1000
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 120
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_per_object = 0
brim_separation = 0
brim_speed = 50%
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 3500
default_speed = 100
dont_support_bridges = 1
draft_shield = disabled
duplicate_distance = 6
enforce_full_fill_volume = 1
enforce_retract_first_layer = 0
ensure_vertical_shell_thickness = 0
external_infill_margin = 4
external_perimeter_acceleration = 750
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_change_odd_layers = 0
external_perimeter_extrusion_spacing = 
external_perimeter_extrusion_width = 100%
external_perimeter_overlap = 100%
external_perimeter_speed = 80
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_spacing = 
extrusion_width = 115%
fill_aligned_z = 1
fill_angle = 45
fill_angle_cross = 1
fill_angle_follow_model = 0
fill_angle_increment = 0
fill_angle_template = 
fill_density = 20%
fill_pattern = rectilinear
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 1000
first_layer_acceleration_over_raft = 0
first_layer_extrusion_spacing = 
first_layer_extrusion_width = 125%
first_layer_flow_ratio = 100%
first_layer_height = 0.3
first_layer_infill_speed = 60
first_layer_min_speed = 0
first_layer_size_compensation = -0.1
first_layer_size_compensation_layers = 2
first_layer_speed = 30
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 200%
fuzzy_skin_thickness = 150%
gap_fill_acceleration = 1000
gap_fill_enabled = 1
gap_fill_extension = 0
gap_fill_flow_match_perimeter = 0%
gap_fill_last = 1
gap_fill_max_width = 0
gap_fill_min_area = 50%
gap_fill_min_length = 0
gap_fill_min_width = 0
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0
gcode_substitutions = 
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
hole_to_polyhole_threshold = 0.01
hole_to_polyhole_twisted = 1
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_bridge = connected
infill_connection_solid = notconnected
infill_connection_top = notconnected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_change_odd_layers = 0
infill_extrusion_spacing = 
infill_extrusion_width = 160%
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 300
inherits = 
interface_shells = 0
internal_bridge_acceleration = 3000
internal_bridge_speed = 100%
ironing = 0
ironing_acceleration = 1000
ironing_angle = -1
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 11
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 35
min_width_top_surface = 200%
mmu_segmented_region_max_width = 0
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes = ---------------------Changelog---------------\n2024-04-15 Upped Wall Thickness to default 4 Top 4 Bottom 4\n2023-11-15 Baseline +90deg Bridges for better fit with Camera mount
object_gcode = 
only_one_perimeter_first_layer = 0
only_one_perimeter_top = 1
only_one_perimeter_top_other_algo = 0
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
over_bridge_flow_ratio = 100%
overhangs_acceleration = 1000
overhangs_bridge_threshold = -1
overhangs_bridge_upper_layers = 0
overhangs_max_slope = 0
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_speed_enforce = 0
overhangs_width = 75%
overhangs_width_speed = 0
parallel_objects_step = 0
perimeter_acceleration = 1000
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_change_odd_layers = 0
perimeter_extrusion_spacing = 
perimeter_extrusion_width = 0
perimeter_generator = classic
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_reverse = 0
perimeter_round_corners = 0
perimeter_speed = 150
perimeters = 4
perimeters_hole = -1
post_process = 
priming_position = 0x0
print_custom_variables = wall_thickness_lines = 7\n
print_extrusion_multiplier = 100%
print_first_layer_temperature = 0
print_retract_length = -1
print_retract_lift = -1
print_settings_id = Tuned Standard
print_temperature = 0
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_interface_layer_height = 0
raft_layer_height = 0
raft_layers = 0
region_gcode = 
resolution = 0.0125
resolution_internal = 0.1
seam_angle_cost = 100%
seam_notch_all = 0
seam_notch_angle = 250
seam_notch_inner = 0
seam_notch_outer = 0
seam_position = cost
seam_travel_cost = 0%
seam_visibility = 1
single_extruder_multi_material_priming = 1
skirt_brim = 0
skirt_distance = 5
skirt_distance_from_brim = 1
skirt_extrusion_width = 0
skirt_height = 1
skirts = 5
slice_closing_radius = 0.049
slicing_mode = regular
small_area_infill_flow_compensation = 0
small_area_infill_flow_compensation_model = 0:10:2:0x0:0.2x0.44:0.4x0.61:0.6x0.7:0.8x0.76:1.5x0.86:2x0.89:3x0.92:5x0.95:10x1
small_perimeter_max_length = 20
small_perimeter_min_length = 6
small_perimeter_speed = 30
solid_fill_pattern = monotonic
solid_infill_acceleration = 3000
solid_infill_below_area = 0
solid_infill_below_layer_area = 0
solid_infill_below_width = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_change_odd_layers = 0
solid_infill_extrusion_spacing = 
solid_infill_extrusion_width = 140%
solid_infill_overlap = 100%
solid_infill_speed = 200
solid_over_perimeters = 0
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_acceleration = 3500
support_material_angle = 0
support_material_angle_height = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_bottom_interface_pattern = auto
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.1
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_acceleration = 3500
support_material_interface_angle = 90
support_material_interface_angle_increment = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layer_height = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100
support_material_layer_height = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 120
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_top_interface_pattern = rectilinear
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_perimeters = 80%
thin_perimeters_all = 20%
thin_walls = 1
thin_walls_acceleration = 750
thin_walls_merge = 1
thin_walls_min_width = 33%
thin_walls_overlap = 50%
thin_walls_speed = 80
threads = 8
top_fill_pattern = monotonicgapfill
top_infill_extrusion_spacing = 
top_infill_extrusion_width = 100%
top_solid_infill_acceleration = 1000
top_solid_infill_overlap = 100%
top_solid_infill_speed = 60
top_solid_layers = 4
top_solid_min_thickness = 0
travel_acceleration = 3500
travel_deceleration_use_target = 1
travel_speed = 300
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_speed = 80
wipe_tower_width = 60
wipe_tower_wipe_starting_speed = 33%
wipe_tower_x = 180
wipe_tower_y = 140
xy_inner_size_compensation = 0
xy_size_compensation = 0

[filament:Formfutura ApolloX ASA White]
bed_temperature = 105
bridge_fan_speed = 100
chamber_temperature = 50
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 30
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.93
fan_below_layer_time = 15
filament_colour = #FFFFFF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 29.99
filament_custom_variables = ""
filament_density = 1.05
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "---------------------Changelog---------------\n2023-12-15 Upped Temps to 255 250 fo rbetter layer adhesion. Seems to have worked. ilament might have gotten a tad wet"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "Formfutura ApolloX ASA White"
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 110
first_layer_temperature = 255
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 90%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 10
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 250
top_fan_speed = -1

[filament:Polymaker Polylite ASA White]
bed_temperature = 105
bridge_fan_speed = 100
chamber_temperature = 50
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 30
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.93
fan_below_layer_time = 15
filament_colour = #FFFFFF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 29.99
filament_custom_variables = ""
filament_density = 1.05
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "---------------------Changelog---------------\n2023-12-15 Upped Temps to 255 250 fo rbetter layer adhesion. Seems to have worked. Filament might have gotten a tad wet"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "Formfutura ApolloX ASA White"
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 110
first_layer_temperature = 255
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 90%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 10
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 250
top_fan_speed = -1

[filament:Prusament ASA Jet Black]
bed_temperature = 110
bridge_fan_speed = 90
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 32
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.96
fan_below_layer_time = 20
filament_colour = #707070
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 42
filament_custom_variables = ""
filament_density = 1.07
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "set Chamber Temp to 20deg"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "Prusament ASA Jet Black"
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 193
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ASA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 115
first_layer_temperature = 265
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 260
top_fan_speed = -1

[filament:eSUN ABS+ Black Backup]
bed_temperature = 105
bridge_fan_speed = 90
chamber_temperature = 25
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 62
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.97
fan_below_layer_time = 20
filament_colour = #4D4D4D
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 22.36
filament_custom_variables = ""
filament_density = 1.03
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "2024-06-13 99% Shrinkage Setting - Seeing some underextrusion?\n2024-12-05 Prints didnt turn out well - Nozzle clogged? too cold? extrusion multipliertoo low? - also need to check the shrinkage, didn prints turn out well? Wahrscheinlich ist der Luefter bei kaelteren Temperaturen uebermaessig effektiv...\nmax Fan speed on layer time to 100->70%\nfan on slow layer time 15->20s\nExtrusion multiplier to 0.97\nNeed to check Exhaust Fan (was running always)\ngood results on Joshis Lenkerstange - nicht so gut beim Nevermore V6\n\n"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN ABS+ Black tobe tuned"
filament_shrink = 99%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 110
first_layer_temperature = 250
full_fan_speed_layer = 3
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 70
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 10
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 247
top_fan_speed = -1

[filament:eSUN ABS+ Black MAIN]
bed_temperature = 110
bridge_fan_speed = 90
chamber_temperature = 25
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 60
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.97
fan_below_layer_time = 20
filament_colour = #4D4D4D
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 22.36
filament_custom_variables = ""
filament_density = 1.03
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "2024-06-13 99% Shrinkage Setting - Seeing some underextrusion?\n2024-12-05 Prints didnt turn out well - Nozzle clogged? too cold? extrusion multipliertoo low? - also need to check the shrinkage, didn prints turn out well? Wahrscheinlich ist der Luefter bei kaelteren Temperaturen uebermaessig effektiv...\nmax Fan speed on layer time to 100->70%\nfan on slow layer time 15->20s\nExtrusion multiplier to 0.97\nNeed to check Exhaust Fan (was running always)\ngood results on Joshis Lenkerstange - nicht so gut beim Nevermore V6\n2024-12-11 Uped Bed Temp to 115 and 110 for better Bed Adhesion\n  lowered fan speed 62-60\n  upped Extrdue Temp to 252 and 250 - Ellis profile used 250\n\n\n"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN ABS+ Black tobe tuned"
filament_shrink = 99%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 115
first_layer_temperature = 252
full_fan_speed_layer = 3
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 70
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 250
top_fan_speed = -1

[filament:eSUN ABS+ Yellow Backup]
bed_temperature = 105
bridge_fan_speed = 100
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 65
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.97
fan_below_layer_time = 20
filament_colour = #FCD912
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 22.36
filament_custom_variables = ""
filament_density = 1.03
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "------------------Changelog-----------------\n2024-04-15 Baseline Test with Slimmelezer Case - worked fine also with supports -very tight fit, but fit\n2024-04-17 change shrinkage by one percent to improve fit a bit"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN ABS+ Yellow"
filament_shrink = 99%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 110
first_layer_temperature = 250
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 245
top_fan_speed = -1

[filament:eSUN ABS+ Yellow MAIN]
bed_temperature = 105
bridge_fan_speed = 100
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 65
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 0.97
fan_below_layer_time = 20
filament_colour = #FCD912
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 22.36
filament_custom_variables = ""
filament_density = 1.03
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 0
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "------------------Changelog-----------------\n2024-04-15 Baseline Test with Slimmelezer Case - worked fine also with supports -very tight fit, but fit\n2024-04-17 change shrinkage by one percent to improve fit a bit"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN ABS+ Yellow"
filament_shrink = 99%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = ABS
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 110
first_layer_temperature = 250
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 245
top_fan_speed = -1

[filament:eSUN TPU Blue Backup]
bed_temperature = 45
bridge_fan_speed = 100
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 50
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1.02
fan_below_layer_time = 20
filament_colour = #0080FF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 30.5
filament_custom_variables = ""
filament_density = 1.21
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 3
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "2024-08-19 reduced max volumentric flow to 3\n2024-08-17 Lowered extrusion multiplier to 1.02\n2024-08-16 raised extrusion multiplier by 5% to 1.05\n2024-07-03-Looks good, when there is no tension on the filament. Need to investigate on how to improve\nPrint still too fast? went from 5->4\nreduced Fan to 50%\nChamber Temp to 10deg\nPrint Temp up by 5deg to 245 240\n2024-01-01 - Baseline"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN TPU Blue"
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = TPU
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 50
first_layer_temperature = 245
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 240
top_fan_speed = -1

[filament:eSUN TPU Blue MAIN]
bed_temperature = 45
bridge_fan_speed = 100
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
default_fan_speed = 50
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1.02
fan_below_layer_time = 20
filament_colour = #0080FF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 30.5
filament_custom_variables = ""
filament_density = 1.21
filament_deretract_speed = nil
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_overlap = 100%
filament_max_speed = 0
filament_max_volumetric_speed = 3
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "2024-08-19 reduced max volumentric flow to 3\n2024-08-17 Lowered extrusion multiplier to 1.02\n2024-08-16 raised extrusion multiplier by 5% to 1.05\n2024-07-03-Looks good, when there is no tension on the filament. Need to investigate on how to improve\nPrint still too fast? went from 5->4\nreduced Fan to 50%\nChamber Temp to 10deg\nPrint Temp up by 5deg to 245 240\n2024-01-01 - Baseline"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_before_travel = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_seam_gap = 1.79769e+308
filament_settings_id = "eSUN TPU Blue"
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 250
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = TPU
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = (Unknown)
filament_wipe = nil
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
filament_wipe_inside_depth = nil
filament_wipe_inside_end = nil
filament_wipe_inside_start = nil
filament_wipe_only_crossing = nil
filament_wipe_speed = nil
first_layer_bed_temperature = 50
first_layer_temperature = 245
full_fan_speed_layer = 0
gap_fill_fan_speed = -1
infill_fan_speed = -1
inherits = 
internal_bridge_fan_speed = -1
max_fan_speed = 100
max_speed_reduction = 80%
min_print_speed = 10
overhangs_fan_speed = -1
perimeter_fan_speed = -1
slowdown_below_layer_time = 15
solid_infill_fan_speed = -1
start_filament_gcode = "; Filament gcode\n; Macro syntax: https://help.prusa3d.com/article/macros_1775\n\n; Set pressure advance per-filament\n;SET_PRESSURE_ADVANCE ADVANCE=0.0x\n\n; Set pressure advance per-filament for different nozzle sizes\n;{if nozzle_diameter[0]==0.4}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{elsif nozzle_diameter[0]==0.6}SET_PRESSURE_ADVANCE ADVANCE=0.0x\n;{endif}\n\n"
support_material_fan_speed = -1
support_material_interface_fan_speed = -1
temperature = 240
top_fan_speed = -1

[printer:Voron 2.4 350]
arc_fitting = 0
arc_fitting_tolerance = 5%
bed_custom_model = Desktop/Voron/V24_350mm_bed_model.stl
bed_custom_texture = Desktop/Voron/V2_bed_textured_pei.png
bed_shape = 0x0,350x0,350x355,0x355
before_layer_gcode = TIMELAPSE_TAKE_FRAME
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 30
end_gcode = END_PRINT
extra_loading_move = -2
extruder_colour = ""
extruder_extrusion_multiplier_speed = 0:0:1
extruder_fan_offset = 0%
extruder_offset = 0x0
extruder_temperature_offset = 0
fan_kickstart = 0
fan_percentage = 0
fan_printer_min_speed = 0
fan_speedup_overhangs = 1
fan_speedup_time = 1
feature_gcode = 
gcode_ascii = 0
gcode_filename_illegal_char = [<>:"/\\\\|?*]
gcode_flavor = klipper
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
init_z_rotate = 0
layer_gcode = SET_PRINT_STATS_INFO CURRENT_LAYER={layer_num}
lift_min = 0
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 10000,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_travel = 10000,1250
machine_max_acceleration_x = 10000,1000
machine_max_acceleration_y = 10000,1000
machine_max_acceleration_z = 350,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 450,200
machine_max_feedrate_y = 450,200
machine_max_feedrate_z = 30,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 5,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_gcode_per_second = 1500
max_layer_height = 75%
max_print_height = 250
milling_diameter = 
milling_toolchange_end_gcode = 
milling_toolchange_start_gcode = 
milling_z_lift = 
min_layer_height = 0.08
min_length = 0
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = PAUSE
print_host = 
printer_custom_variables = 
printer_model = 
printer_notes = ----------------Changelog----------------\n2024-07-13 moving to klippain slicer variables. Old PRINT_START BED_TEMP=[first_layer_bed_temperature] EXTRUDER_TEMP={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} CHAMBER_TEMP=[chamber_temperature]\n2024-04-29 fixing CHAMBER(_TEMP) to correctly read in Chamber Temperature\n2024-04-17 removed Bed Surface from snapshot\nAdded Custom GCode for Layerphotos
printer_settings_id = Voron 2.4 350
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
printhost_port = 
remaining_times = 1
remaining_times_type = m73
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.5
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0.25
retract_lift_before_travel = 2
retract_lift_below = 0
retract_lift_first_layer = 0
retract_lift_top = "All surfaces"
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_gap = 0
seam_gap_external = 0
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M140 S0\n\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder] + extruder_temperature_offset[initial_extruder]} BED_TEMP=[first_layer_bed_temperature] MATERIAL=[filament_type] SIZE={first_layer_print_min[0]}_{first_layer_print_min[1]}_{first_layer_print_max[0]}_{first_layer_print_max[1]} INITIAL_TOOL={initial_extruder} CHAMBER=[chamber_temperature] TOTAL_LAYER=[total_layer_count]
start_gcode_manual = 0
template_custom_gcode = 
thumbnails = 32x32,400x300
thumbnails_color = #00FF00
thumbnails_custom_color = 0
thumbnails_end_file = 0
thumbnails_format = PNG
thumbnails_tag_format = 0
thumbnails_with_bed = 0
time_cost = 0
time_estimation_compensation = 100%
time_start_gcode = 20
time_toolchange = 30
tool_name = ""
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0
wipe_inside_depth = 50%
wipe_inside_end = 1
wipe_inside_start = 0
wipe_only_crossing = 1
wipe_speed = 0
z_offset = 0
z_step = 0.01

[printer:Voron 2.4 350 Backup]
arc_fitting = 0
arc_fitting_tolerance = 5%
bed_custom_model = Desktop/Voron/V24_350mm_bed_model.stl
bed_custom_texture = Desktop/Voron/V2_bed_textured_pei.png
bed_shape = 0x0,350x0,350x355,0x355
before_layer_gcode = TIMELAPSE_TAKE_FRAME
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 30
end_gcode = END_PRINT
extra_loading_move = -2
extruder_colour = ""
extruder_extrusion_multiplier_speed = 0:0:1
extruder_fan_offset = 0%
extruder_offset = 0x0
extruder_temperature_offset = 0
fan_kickstart = 0
fan_percentage = 0
fan_printer_min_speed = 0
fan_speedup_overhangs = 1
fan_speedup_time = 1
feature_gcode = 
gcode_ascii = 0
gcode_filename_illegal_char = [<>:"/\\\\|?*]
gcode_flavor = klipper
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
init_z_rotate = 0
layer_gcode = SET_PRINT_STATS_INFO CURRENT_LAYER={layer_num}
lift_min = 0
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 10000,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_travel = 10000,1250
machine_max_acceleration_x = 10000,1000
machine_max_acceleration_y = 10000,1000
machine_max_acceleration_z = 350,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 450,200
machine_max_feedrate_y = 450,200
machine_max_feedrate_z = 30,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 5,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_gcode_per_second = 1500
max_layer_height = 75%
max_print_height = 250
milling_diameter = 
milling_toolchange_end_gcode = 
milling_toolchange_start_gcode = 
milling_z_lift = 
min_layer_height = 0.08
min_length = 0
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = PAUSE
print_host = 
printer_custom_variables = 
printer_model = 
printer_notes = ----------------Changelog----------------\n2024-07-13 moving to klippain slicer variables. Old PRINT_START BED_TEMP=[first_layer_bed_temperature] EXTRUDER_TEMP={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} CHAMBER_TEMP=[chamber_temperature]\n2024-04-29 fixing CHAMBER(_TEMP) to correctly read in Chamber Temperature\n2024-04-17 removed Bed Surface from snapshot\nAdded Custom GCode for Layerphotos
printer_settings_id = Voron 2.4 350
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
printhost_port = 
remaining_times = 1
remaining_times_type = m73
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 0.5
retract_length_toolchange = 10
retract_lift = 0.2
retract_lift_above = 0.25
retract_lift_before_travel = 2
retract_lift_below = 0
retract_lift_first_layer = 0
retract_lift_top = "All surfaces"
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_gap = 0
seam_gap_external = 0
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M140 S0\n\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder] + extruder_temperature_offset[initial_extruder]} BED_TEMP=[first_layer_bed_temperature] MATERIAL=[filament_type] SIZE={first_layer_print_min[0]}_{first_layer_print_min[1]}_{first_layer_print_max[0]}_{first_layer_print_max[1]} INITIAL_TOOL={initial_extruder} CHAMBER=[chamber_temperature] TOTAL_LAYER=[total_layer_count]
start_gcode_manual = 0
template_custom_gcode = 
thumbnails = 32x32,400x300
thumbnails_color = #00FF00
thumbnails_custom_color = 0
thumbnails_end_file = 0
thumbnails_format = PNG
thumbnails_tag_format = 0
thumbnails_with_bed = 0
time_cost = 0
time_estimation_compensation = 100%
time_start_gcode = 20
time_toolchange = 30
tool_name = ""
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0
wipe_inside_depth = 50%
wipe_inside_end = 1
wipe_inside_start = 0
wipe_only_crossing = 1
wipe_speed = 0
z_offset = 0
z_step = 0.01

[physical_printer:LAB V2.4]
host_type = klipper
preset_name = Voron 2.4 350;Voron 2.4 350 Backup
preset_names = "Voron 2.4 350";"Voron 2.4 350 Backup"
print_host = mainsailos.local
printer_technology = FFF
printhost_apikey = 
printhost_authorization_type = key
printhost_cafile = 
printhost_client_cert = 
printhost_client_cert_password = 
printhost_password = 
printhost_port = 
printhost_ssl_ignore_revoke = 0
printhost_user = 

[presets]
print = Standard Functional MAIN
sla_print = 
sla_material = 
printer = Voron 2.4 350
filament = eSUN ABS+ Black MAIN
physical_printer = LAB V2.4