truma.yaml

esphome:
  name: "esphome-truma-all-config"

  on_boot:
    then:
      # read time from external source (connected via I2C)
      - ds1307.read_time

external_components:
  - source: github://Fabian-Schmidt/esphome-truma_inetbox
  # - source:
  #     type: local
  #     path: ./components
    components: ["truma_inetbox"]

esp32:
  board: esp32dev
  framework:
    type: arduino

i2c:
  sda: 14
  scl: 27
  scan: false
  id: i2c_bus_a

time:
  - platform: ds1307
    update_interval: never
    id: esptime

uart:
  - id: lin_uart_bus
    tx_pin: 17
    rx_pin: 16
    baud_rate: 9600
    data_bits: 8
    parity: NONE
    stop_bits: 2

truma_inetbox:
  uart_id: lin_uart_bus
  time_id: esptime
  cs_pin: 5
  fault_pin: 18
  # Advanced users can use `on_heater_message` action. The heater data is in the `message` variable.
  on_heater_message:
    then:
    - logger.log: "Message from CP Plus."
    - if:
        condition:
          lambda: return message->operating_status == truma_inetbox::OperatingStatus::OPERATING_STATUS_OFF;
        then:
          - logger.log: "Heater is off."

binary_sensor:
  - platform: truma_inetbox
    name: "CP Plus alive"
    type: CP_PLUS_CONNECTED

  - platform: truma_inetbox
    name: "Room Heater active"
    type: HEATER_ROOM
    id: HEATER_ROOM
  - platform: truma_inetbox
    name: "Water Heater active"
    type: HEATER_WATER
    id: HEATER_WATER
  - platform: truma_inetbox
    name: "Heater mode Gas"
    type: HEATER_GAS
  - platform: truma_inetbox
    name: "Heater mode Mix 1"
    type: HEATER_MIX_1
  - platform: truma_inetbox
    name: "Heater mode Mix 2"
    type: HEATER_MIX_2
  - platform: truma_inetbox
    name: "Heater mode Elec"
    type: HEATER_ELECTRICITY
  - platform: truma_inetbox
    name: "Heater has error"
    type: HEATER_HAS_ERROR

  - platform: truma_inetbox
    name: "Timer active"
    type: TIMER_ACTIVE
    id: TIMER_ACTIVE
  - platform: truma_inetbox
    name: "Timer Room Heater active"
    type: TIMER_ROOM
  - platform: truma_inetbox
    name: "Timer Water Heater active"
    type: TIMER_WATER

climate:
  - platform: truma_inetbox
    name: "Truma Room"
    type: ROOM
  - platform: truma_inetbox
    name: "Truma Water"
    type: WATER

number:
  - platform: truma_inetbox
    name: "Target Room Temperature"
    type: TARGET_ROOM_TEMPERATURE
  - platform: truma_inetbox
    name: "Target Water Temperature"
    type: TARGET_WATER_TEMPERATURE
  - platform: truma_inetbox
    name: "electric power level"
    type: ELECTRIC_POWER_LEVEL
  - platform: truma_inetbox
    name: "Aircon Temperature"
    type: AIRCON_MANUAL_TEMPERATURE

sensor:
  - platform: truma_inetbox
    name: "Current Room Temperature"
    type: CURRENT_ROOM_TEMPERATURE
  - platform: truma_inetbox
    name: "Current Water Temperature"
    type: CURRENT_WATER_TEMPERATURE
  - platform: truma_inetbox
    name: "Target Room Temperature"
    type: TARGET_ROOM_TEMPERATURE
  - platform: truma_inetbox
    name: "Target Water Temperature"
    type: TARGET_WATER_TEMPERATURE
  - platform: truma_inetbox
    name: "Heating mode"
    type: HEATING_MODE
  - platform: truma_inetbox
    name: "electric power level"
    type: ELECTRIC_POWER_LEVEL
  - platform: truma_inetbox
    name: "Energy mix"
    type: ENERGY_MIX
  - platform: truma_inetbox
    name: "Operating status"
    type: OPERATING_STATUS
  - platform: truma_inetbox
    name: "Heater error code"
    type: HEATER_ERROR_CODE

switch:
  - platform: template
    name: "Activate Room Heater"
    lambda: |-
      return id(HEATER_ROOM).state;
    turn_on_action:
      - truma_inetbox.heater.set_target_room_temperature:
          # You can use lambda functions
          temperature: !lambda |-
            return 16;
          # Optional set heating mode: `"OFF"`, `ECO`, `HIGH`, `BOOST`
          heating_mode: ECO
    turn_off_action:
      - truma_inetbox.heater.set_target_room_temperature:
          # Disable heater by setting temperature to `0`.
          temperature: 0
  - platform: template
    name: "Activate Water Heater"
    lambda: |-
      return id(HEATER_WATER).state;
    turn_on_action:
      - truma_inetbox.heater.set_target_water_temperature:
          # Set water temp as number: `0`, `40`, `60`, `80`
          temperature: 40
    turn_off_action:
      - truma_inetbox.heater.set_target_water_temperature:
          # Disable heater by setting temperature to `0`.
          temperature: 0
  - platform: template
    name: "Activate Water Heater (enum)"
    lambda: |-
      return id(HEATER_WATER).state;
    turn_on_action:
      - truma_inetbox.heater.set_target_water_temperature_enum:
          # Set water temp as text: `"OFF"`, `ECO`, `HIGH`, `BOOST`
          temperature: ECO
    turn_off_action:
      # You can also use the simplified syntax.
      - truma_inetbox.heater.set_target_water_temperature_enum: "OFF"
  - platform: template
    name: "Active Timer"
    lambda: |-
      return id(TIMER_ACTIVE).state;
    turn_on_action:
      - truma_inetbox.timer.activate:
          start: 7:00
          stop: 9:30
          # Required: Set room temp to a number between 5 and 30
          room_temperature: 13
          # Optional: Set heating mode: `"OFF"`, `ECO`, `HIGH`, `BOOST`
          heating_mode: ECO
          # Optional: Set water temp as number: `0`, `40`, `60`, `80`
          water_temperature: 0
          # Optional: Set energy mix to: `GAS`, `MIX`, `ELECTRICITY`
          energy_mix: GAS
          # Optional: Set electricity level to `0`, `900`, `1800`
          watt: 0

    turn_off_action:
      # You can also use the simplified syntax.
      - truma_inetbox.timer.disable

button:
  - platform: template
    name: "Energy mix GAS only"
    on_press:
      - truma_inetbox.heater.set_energy_mix:
          # Set energy mix to: `GAS`, `MIX`, `ELECTRICITY`
          energy_mix: GAS
  - platform: template
    name: "Energy mix MIX 1"
    on_press:
      - truma_inetbox.heater.set_energy_mix:
          energy_mix: MIX
          # Set electricity level to `0`, `900`, `1800`
          watt: 900W
  - platform: template
    name: "Energy mix MIX 2"
    on_press:
      - truma_inetbox.heater.set_energy_mix:
          energy_mix: MIX
          watt: 1800
  - platform: template
    name: "Energy mix ELECTRICITY only"
    on_press:
      - truma_inetbox.heater.set_energy_mix:
          energy_mix: ELECTRICITY
          watt: 1800W
  - platform: template
    name: "Set electric power level to 0 Watt"
    on_press:
      - truma_inetbox.heater.set_electric_power_level: 0
  - platform: template
    name: "Set electric power level to 900 Watt"
    on_press:
      - truma_inetbox.heater.set_electric_power_level: 900
  - platform: template
    name: "Set electric power level to 1800 Watt"
    on_press:
      - truma_inetbox.heater.set_electric_power_level: 1800

wifi:
  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Fallback Hotspot"
    password: "Sw9g4XJtoyrn"

web_server:
  port: 80
  local: true
  version: 2
  include_internal: true