kubernetesinstallation.txt

installing kubernetes cluster



# Kubeadm Installation Guide

This guide outlines the steps needed to set up a Kubernetes cluster using kubeadm.

## Pre-requisites

- Ubuntu OS 

- t2.medium instance type or higher

---

## AWS Setup

- Make sure all traffic is allowed on all instance

---

## Execute on Both "Master" & "Worker Node"

Run the following commands on both the master and worker nodes to prepare them for kubeadm.
=============================================================================================================

# disable swap
sudo swapoff -a

# Create the .conf file to load the modules at bootup
cat <<EOF | sudo tee /etc/modules-load.d/k8s.conf
overlay
br_netfilter
EOF

sudo modprobe overlay
sudo modprobe br_netfilter

# sysctl params required by setup, params persist across reboots
cat <<EOF | sudo tee /etc/sysctl.d/k8s.conf
net.bridge.bridge-nf-call-iptables  = 1
net.bridge.bridge-nf-call-ip6tables = 1
net.ipv4.ip_forward                 = 1
EOF

# Apply sysctl params without reboot
sudo sysctl --system

## Install CRIO Runtime
sudo apt-get update -y
sudo apt-get install -y software-properties-common curl apt-transport-https ca-certificates gpg

sudo curl -fsSL https://pkgs.k8s.io/addons:/cri-o:/prerelease:/main/deb/Release.key | sudo gpg --dearmor -o /etc/apt/keyrings/cri-o-apt-keyring.gpg
echo "deb [signed-by=/etc/apt/keyrings/cri-o-apt-keyring.gpg] https://pkgs.k8s.io/addons:/cri-o:/prerelease:/main/deb/ /" | sudo tee /etc/apt/sources.list.d/cri-o.list

sudo apt-get update -y
sudo apt-get install -y cri-o

sudo systemctl daemon-reload
sudo systemctl enable crio --now
sudo systemctl start crio.service

echo "CRI runtime installed successfully"

# Add Kubernetes APT repository and install required packages
curl -fsSL https://pkgs.k8s.io/core:/stable:/v1.29/deb/Release.key | sudo gpg --dearmor -o /etc/apt/keyrings/kubernetes-apt-keyring.gpg
echo 'deb [signed-by=/etc/apt/keyrings/kubernetes-apt-keyring.gpg] https://pkgs.k8s.io/core:/stable:/v1.29/deb/ /' | sudo tee /etc/apt/sources.list.d/kubernetes.list

sudo apt-get update -y
sudo apt-get install -y kubelet="1.29.0-*" kubectl="1.29.0-*" kubeadm="1.29.0-*"
sudo apt-get update -y
sudo apt-get install -y jq

sudo systemctl enable --now kubelet
sudo systemctl start kubelet

---------------------------------------------------
## Execute ONLY on "Master Node"


sudo kubeadm config images pull

sudo kubeadm init

mkdir -p "$HOME"/.kube
sudo cp -i /etc/kubernetes/admin.conf "$HOME"/.kube/config
sudo chown "$(id -u)":"$(id -g)" "$HOME"/.kube/config


# Network Plugin = calico

kubectl apply -f https://raw.githubusercontent.com/projectcalico/calico/v3.26.0/manifests/calico.yaml

--------------------------------------------------------

## Execute on ALL of your Worker Node's

1. Perform pre-flight checks


   sudo kubeadm reset pre-flight checks


2. Paste the join command you got from the master node and append `--v=5` at the end but first use sudo su command to become root (avoid using sudo your-token).

   sudo su
   <your-token --v=5>


## Verify Cluster Connection

**On Master Node:**


kubectl get nodes